Sony KV-29FQ85K: Learning functions from other Remote Controls

Learning functions from other Remote Controls: Sony KV-29FQ85K

Learning functions from other Remote Controls

To eliminate the amount of remote controls you need, this remote control has a learning feature. Once set up

as explained below, it can be used in place of your other remote controls.

It is recommended that you make a note of what each button has been taught (you can use the table provided

with the remote control).

Before you start and for accurate learning, please read below instructions:

• Choose the button (a-g) you want to learn. The buttons which can learn a new function, have a blue dot. See

fig. 3 to find out the possible buttons.

• Do not move the remote units during the learning procedure.

• Be sure to keep holding down the learning button until your commander reacts as described.

• Use fresh batteries in both remote units.

• Avoid learning in places subjects to direct sunlight or a strong fluorescent light.

• Noise may interfere during the learning procedure.

• The remote control detector area may differ depending on each remote unit. If learning does not work, try

changing the positions of the two remote controls.

• It is possible that some specific remote control signals may not be learned.

• If you do not perform the learning steps within 20 seconds at any point during the process, the learning mode

ends.

fig. 1

2-3 cm.

1 Position both remote controls as shown (see fig. 1).

fig. 3

2 Press and hold the t button of this TV remote control for

approximately 6 seconds, until the AUX green light starts flashing

a

This TV remote

Other remote

(see fig.2).

control

control

fig. 2

3 Press the button (a-g, see fig. 3) of this TV remote control on which

D

you wish to store a learned function.

T

V

V

D

A

R

U

C

X

V

Once the selected button has been pressed, the VCR, TV, DVD and

MODE

AUX illuminate flash in order (see fig. 4).

b

6 sec.

g

4 Press the button from the other remote control that you wish to teach your

fig. 4

c

TV remote control.

• During the data transfer process, all the four lights illuminate at the

T

V

D

V

D

same time (see fig. 5).

A

R

U

C

X

d

V

• As soon as data transfer is finished, the AUX green light starts

flashing (see fig. 6).

MODE

e

5 If you wish to record other functions repeat steps 2-4 (read before the

fig. 5

warning below), otherwise go to step 6.

V

D

T

V

D

• In case you try to select one button which has been already

A

R

U

f

C

X

V

learned, all the four lights will momentarily flash very shortly and

the remote control automatically return to the same condition as

MODE

in the step 2 with the AUX light flashing

• In case you try to select a not-learnable button, the remote control

fig. 6

stay in to the same condition as in the step 2 with the AUX light

T

V

D

V

D

flashing.

A

R

U

C

X

V

6 Press the t button to finish the learning process.

MODE

7 Check that all the learning functions have been learned correctly.

To use a learned function later, press the T or t buttons to select AUX and next

press the relevant button.

• Always remember to press the

T or t button until the green light iluminates

according to the equipment you want to operate with this remote control: VCR, TV,

DVD or AUX.

continued...

24

Additional Information

Erasing a learned function

fig. 7

1 Press and hold the t button for approximately six seconds until the

a

T

V

D

V

D

AUX green light flashes (see fig. 7).

A

R

U

C

X

V

2 While pressing the % button, press the button (a - g) with the learned

MODE

function that you want to erase.

6 sec.

All the four lights illuminate at the same time (see fig. 8) and as

soon as the learned function is erased, the AUX green light starts

fig. 8

b

flashing (see fig. 9).

T

V

D

V

D

A

R

U

3 If you wish to store a new function, repeat steps 3 and 4 from the

C

X

V

g

c

previous page, otherwise press the t button to return to normal

MODE

operation.

d

Erasing all the learned functions in one time

fig. 9

D

e

T

V

V

D

1 Press and hold the t button for approximately six seconds, until the

A

U

R

C

X

AUX green light flashes (see fig. 7).

V

MODE

2 While pressing the % button, press t to erase all the learned

GB

functions.

f

All the four lights illuminate at the same time (see fig. 8) and as

soon as all the learned function are erased, the remote control

automatically returns to the normal operation.

Additional Information

25

Оглавление