Sony KV-SW252: инструкция
Раздел: Бытовая, кухонная техника, электроника и оборудование
Тип: Телевизор
Инструкция к Телевизору Sony KV-SW252
2-655-047-11 (1)
Trinitron Color TV
GB
Operating Instructions
• Before operating the unit, please read this manual thoroughly and retain
it for future reference.
RU
Инструкция по эксплуатации
• Перед работой с устройством внимательно прочтайте инструкцию
и сохраните её для дальнейшего использования.
KV-SW292
KV-SW252
M91
© 2005 Sony Corporation
WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 220 – 240 V AC.
• Do not plug in the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
• To avoid battery leakage and damage to the remote, remove the batteries from the
remote if you are not going to use it for several days. If any liquid leaks from the
batteries and touches your skin, immediately wash it away with water.
For your own safety, do not touch
For children’s safety, do not leave
To prevent fire or shock hazard, do
any part of the TV, the power cord
children alone with the TV. Do not
not expose the TV to rain or
and the antenna cable during
allow children to climb onto it.
moisture.
lightning storms.
Do not place any objects on the TV.
Do not operate the TV if any liquid
Install the TV on a stable TV stand
The apparatus shall not be
or solid object falls into it. Have it
and floor which can support the
exposed to dripping or splashing
checked immediately by qualified
TV set weight. Ensure that the TV
and that no objects filled with
personnel only.
stand surface is flat and its area is
liquids, such as vases, shall be
larger than the bottom area of the
placed on the apparatus.
TV.
Do not block the ventilation
Your TV is recommended for
Do not plug in too many
openings of the TV. Do not install
home use only. Do not use the TV
appliances to the same power
the TV in a confined space, such
in any vehicle or where it may be
socket. Do not damage the power
as a bookcase or built-in cabinet.
subject to excessive dust, heat,
cord.
moisture or vibrations.
Do not open the cabinet and the
Clean the TV with a dry and soft
Pull the power cord out by the
rear cover of the TV as high
cloth. Do not use benzine, thinner,
plug. Do not pull the power cord
voltages and other hazards are
or any other chemicals to clean the
itself. Even if your TV is turned
present inside the TV. Refer
TV. Do not attach anything (e.g.,
off, it is still connected to the AC
servicing and disposal of the TV
adhesive tape, cellophane tape,
power source (mains) as long as
to qualified personnel.
glue) on the painted cabinet of the
the power cord is plugged in.
TV. Do not scratch the picture
Unplug the TV before moving it
tube.
or if you are not going to use it for
several days.
2
Table of Contents
Installation
Menu Adjustment
Securing the TV .................................... 4
Introducing the WEGA GATE
Getting Started ..................................... 5
navigator ............................................. 15
Setting up your TV
“Settings” Adjustment ...................... 16
(“Initial Setup”) .................................... 6
Changing the “Picture” setting ........ 17
Changing the “Sound” setting ......... 18
Overview of Controls
Changing the “Channel Setup”
setting .................................................. 19
TV front and rear panels ..................... 8
Changing the “Setup” setting .......... 21
Using the remote control and
basic functions ...................................... 9
GB
Additional Information
Advanced Operations
Connecting optional components ... 22
Selecting the picture and sound
Troubleshooting ................................. 24
modes .................................................. 11
Specifications ...................................... 26
Listening to the FM Radio ................ 12
Enjoying stereo or bilingual
programs ............................................. 13
Viewing Teletext ................................. 14
Made in Malaysia.
Sony Corporation
6-7-35 Kitashinagawa,
Shinagawa-ku, Tokyo, 141-0001 Japan.
3
Installation
x Securing the TV
To prevent the TV from falling, use the supplied screws, clamps and band to
secure the TV.
20 mm
3.8 mm
screws clamps band
Screw the band to the TV stand and to the
provided hole at the rear of your TV.
or
(1) Put a cord or chain through the clamps.
(2) Screw one clamp to a wall or pillar and
the other clamp to the provided hole at
the rear of your TV.
or
(1) Attach each end of a cord or chain to
the provided holders at the rear of your
TV.
(2) Securely fix the attached cord or chain
to a wall or pillar using an attachment
which can support the TV set weight.
Note
• Use only the supplied screws. Use of other screws may damage the TV.
4 Installation
x Getting Started
Step 1
Insert the batteries (supplied) into the remote.
b
Note
• Do not use old or different types of batteries together.
Installation
Step 2
Connect the antenna cable (not supplied) to 8
(antenna input) at the rear of the TV.
Tips
• Your TV can receive both TV and FM radio signal from the
appropriate connections through the 8 (antenna input)
terminal (see page 22).
• You can also connect your TV to other optional components
(see page 22).
Step 3
Plug in the power cord, then press ! on the TV to
b
turn it on.
Note
• The 1 (standby) indicator flashes green for a few seconds
when turning on the TV. This does not indicate a
malfunction.
Step 4
Set up the TV by following the instructions of the
“Начальная настройкa” (“Initial Setup”) menu (see
page 6).
Installation
5
x
Setting up your TV
(“Initial Setup”)
When you turn on your TV for the first time, the “Initial Setup” menu will
appear. You may change the menu language, preset the TV channels
automatically, sort or edit the channels and adjust the picture position using the
buttons on the remote control or TV front panel.
Press V or v to select the desired menu
1
language, then press
.
The selected menu language appears.
Press V or v to select “Yes”, then press
2
to preset the channels automatically.
The screen will indicate automatic
presetting is in progress.
After all available channels have been tuned
and stored, the “Program Sorting/Edit”
menu appears automatically on the screen.
To skip automatic channel presetting, select
“No”, then press
.
If the message “No channel found. Please
connect cable/antenna” appears, check your
TV connections, then press
.
The “Program Sorting/Edit” menu enables
3
you to sort and edit the channels.
a) If you wish to keep the channels in the current
condition, press WEGA GATE to exit.
b) Press V or v to select the program
number with the channel you wish to
change. The selected channel will appear
on the screen.
c) If you wish to store the channels in a
different order:
1) Press b to enter sorting mode.
2) Press V or v to select the new program
number position for your selected channel,
then press B.
6 Installation
Select
Confirm
End
Select
Confirm
End
Program:
01
TV System: Auto
VHF Low
End
Program Sorting/Edit
PROG
SkipLabel
01
Off
02
Off
03
Off01
04
Off
Sorting mode
Select
Confirm
Exit
Program Sorting/Edit
PROG
SkipLabel
01
Off
02
Off
03
Off
04
Off
Sorting:
Edit:
Select
Confirm
Exit
d) If you wish to edit the channels, press
to change to edit mode.
Press b until the mode that you wish to edit
is highlighted: Label, Skip,
(block symbol).
Then press
.
1) To label, press V or v to select the
Select
Confirm
Exit
alphanumeric characters for the label.
Then press
.
Installation
2) To skip the program number, press V or v to
select “On”. Then press
.
You can skip this program number when
Select
Confirm
Exit
using PROG +/-.
3) To block unwanted program number,
press V or v to select
. Then press .
e) Repeat step b) to d) if you wish to change other
Select
Confirm
Exit
channels.
Press WEGA GATE to go to the next menu.
Press B or b to adjust the bars on the top
4
and bottom of the menu if they are
slanted, then press
.
Select
Confirm
End
“Picture V-Position” menu appears.
If the upper and lower bars are not
5
equally positioned to the top and
bottom of the screen, press V or v to
adjust them, then press
.
Select
Confirm
End
If no adjustment is necessary, then press
.
To prevent this “Initial Setup” menu from
6
appearing again when you turn on the TV
by pressing !, press V or v to select “No”,
then press
.
To allow this menu to appear again, select
“Yes”, then press
.
Tip
• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.
Installation
7
Select
Confirm