Sony KV-SW292: инструкция

2-655-047-11 (1)

Trinitron Color TV

GB

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain

it for future reference.

RU

Инструкция по эксплуатации

• Перед работой с устройством внимательно прочтайте инструкцию

и сохраните её для дальнейшего использования.

KV-SW292

KV-SW252

M91

© 2005 Sony Corporation

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 220 – 240 V AC.

• Do not plug in the power cord until you have completed making all other

connections; otherwise a minimum leakage current might flow through the antenna

and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the

remote if you are not going to use it for several days. If any liquid leaks from the

batteries and touches your skin, immediately wash it away with water.

For your own safety, do not touch

For children’s safety, do not leave

To prevent fire or shock hazard, do

any part of the TV, the power cord

children alone with the TV. Do not

not expose the TV to rain or

and the antenna cable during

allow children to climb onto it.

moisture.

lightning storms.

Do not place any objects on the TV.

Do not operate the TV if any liquid

Install the TV on a stable TV stand

The apparatus shall not be

or solid object falls into it. Have it

and floor which can support the

exposed to dripping or splashing

checked immediately by qualified

TV set weight. Ensure that the TV

and that no objects filled with

personnel only.

stand surface is flat and its area is

liquids, such as vases, shall be

larger than the bottom area of the

placed on the apparatus.

TV.

Do not block the ventilation

Your TV is recommended for

Do not plug in too many

openings of the TV. Do not install

home use only. Do not use the TV

appliances to the same power

the TV in a confined space, such

in any vehicle or where it may be

socket. Do not damage the power

as a bookcase or built-in cabinet.

subject to excessive dust, heat,

cord.

moisture or vibrations.

Do not open the cabinet and the

Clean the TV with a dry and soft

Pull the power cord out by the

rear cover of the TV as high

cloth. Do not use benzine, thinner,

plug. Do not pull the power cord

voltages and other hazards are

or any other chemicals to clean the

itself. Even if your TV is turned

present inside the TV. Refer

TV. Do not attach anything (e.g.,

off, it is still connected to the AC

servicing and disposal of the TV

adhesive tape, cellophane tape,

power source (mains) as long as

to qualified personnel.

glue) on the painted cabinet of the

the power cord is plugged in.

TV. Do not scratch the picture

Unplug the TV before moving it

tube.

or if you are not going to use it for

several days.

2

Table of Contents

Installation

Menu Adjustment

Securing the TV .................................... 4

Introducing the WEGA GATE

Getting Started ..................................... 5

navigator ............................................. 15

Setting up your TV

“Settings” Adjustment ...................... 16

(“Initial Setup”) .................................... 6

Changing the “Picture” setting ........ 17

Changing the “Sound” setting ......... 18

Overview of Controls

Changing the “Channel Setup”

setting .................................................. 19

TV front and rear panels ..................... 8

Changing the “Setup” setting .......... 21

Using the remote control and

basic functions ...................................... 9

GB

Additional Information

Advanced Operations

Connecting optional components ... 22

Selecting the picture and sound

Troubleshooting ................................. 24

modes .................................................. 11

Specifications ...................................... 26

Listening to the FM Radio ................ 12

Enjoying stereo or bilingual

programs ............................................. 13

Viewing Teletext ................................. 14

Made in Malaysia.

Sony Corporation

6-7-35 Kitashinagawa,

Shinagawa-ku, Tokyo, 141-0001 Japan.

3

Installation

x Securing the TV

To prevent the TV from falling, use the supplied screws, clamps and band to

secure the TV.

20 mm

3.8 mm

screws clamps band

Screw the band to the TV stand and to the

provided hole at the rear of your TV.

or

(1) Put a cord or chain through the clamps.

(2) Screw one clamp to a wall or pillar and

the other clamp to the provided hole at

the rear of your TV.

or

(1) Attach each end of a cord or chain to

the provided holders at the rear of your

TV.

(2) Securely fix the attached cord or chain

to a wall or pillar using an attachment

which can support the TV set weight.

Note

• Use only the supplied screws. Use of other screws may damage the TV.

4 Installation

x Getting Started

Step 1

Insert the batteries (supplied) into the remote.

b

Note

• Do not use old or different types of batteries together.

Installation

Step 2

Connect the antenna cable (not supplied) to 8

(antenna input) at the rear of the TV.

Tips

• Your TV can receive both TV and FM radio signal from the

appropriate connections through the 8 (antenna input)

terminal (see page 22).

• You can also connect your TV to other optional components

(see page 22).

Step 3

Plug in the power cord, then press ! on the TV to

b

turn it on.

Note

• The 1 (standby) indicator flashes green for a few seconds

when turning on the TV. This does not indicate a

malfunction.

Step 4

Set up the TV by following the instructions of the

“Начальная настройкa” (“Initial Setup”) menu (see

page 6).

Installation

5

x

Setting up your TV

(“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will

appear. You may change the menu language, preset the TV channels

automatically, sort or edit the channels and adjust the picture position using the

buttons on the remote control or TV front panel.

Press V or v to select the desired menu

1

language, then press

.

The selected menu language appears.

Press V or v to select “Yes”, then press

2

to preset the channels automatically.

The screen will indicate automatic

presetting is in progress.

After all available channels have been tuned

and stored, the “Program Sorting/Edit”

menu appears automatically on the screen.

To skip automatic channel presetting, select

“No”, then press

.

If the message “No channel found. Please

connect cable/antenna” appears, check your

TV connections, then press

.

The “Program Sorting/Edit” menu enables

3

you to sort and edit the channels.

a) If you wish to keep the channels in the current

condition, press WEGA GATE to exit.

b) Press V or v to select the program

number with the channel you wish to

change. The selected channel will appear

on the screen.

c) If you wish to store the channels in a

different order:

1) Press b to enter sorting mode.

2) Press V or v to select the new program

number position for your selected channel,

then press B.

6 Installation

Select

Confirm

End

Program Sorting/Edit

PROG

SkipLabel

01

Off

02

Off

03

Off

04

Off

Sorting:

Edit:

Select

Confirm

Exit

d) If you wish to edit the channels, press

to change to edit mode.

Press b until the mode that you wish to edit

is highlighted: Label, Skip,

(block symbol).

Then press

.

1) To label, press V or v to select the

Select

Confirm

Exit

alphanumeric characters for the label.

Then press

.

Installation

2) To skip the program number, press V or v to

select “On”. Then press

.

You can skip this program number when

Select

Confirm

Exit

using PROG +/-.

3) To block unwanted program number,

press V or v to select

. Then press .

e) Repeat step b) to d) if you wish to change other

Select

Confirm

Exit

channels.

Press WEGA GATE to go to the next menu.

Press B or b to adjust the bars on the top

4

and bottom of the menu if they are

slanted, then press

.

Select

Confirm

End

“Picture V-Position” menu appears.

If the upper and lower bars are not

5

equally positioned to the top and

bottom of the screen, press V or v to

adjust them, then press

.

Select

Confirm

End

If no adjustment is necessary, then press

.

To prevent this “Initial Setup” menu from

6

appearing again when you turn on the TV

by pressing !, press V or v to select “No”,

then press

.

To allow this menu to appear again, select

“Yes”, then press

.

Tip

• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.

Installation

7