Sony DSC-TX10 Silver: инструкция

4-265-636-44(1)

Digital Still Camera / Instruction Manual GB

Цифровой фотоаппарат / Инструкция по эксплуатации

RU

Цифровий фотоапарат / Посібник з експлуатації UA

DSC-TX10

English

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call your Sony dealer

regarding this product.

Model No. DSC-TX10

Serial No. ______________________________

Model No. AC-UB10/UB10B

Serial No. ______________________________

WARNING

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

IMPORTANT SAFETY INSTRUCTIONS

-SAVE THESE INSTRUCTIONS

DANGER

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, CAREFULLY FOLLOW THESE

INSTRUCTIONS

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

CAUTION

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

GB

• Do not incinerate or dispose of in fire.

2

• Do not handle damaged or leaking lithium ion batteries.

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ AC Adaptor

Connect the AC Adaptor to the nearest wall outlet (wall socket).

GB

If some trouble occurs while using the AC Adaptor, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

The power cord (mains lead), if supplied, is designed specifically for use with this camera

only, and should not be used with other electrical equipment.

For Customers in the U.S.A. and Canada

[ RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment by returning your used

rechargeable batteries to the collection and recycling location nearest

you.

For more information regarding recycling of rechargeable batteries,

call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Battery pack

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

For Customers in the U.S.A.

UL is an internationally recognized safety organization.

The UL Mark on the product means it has been UL Listed.

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669).

GB

The number below is for the FCC related matters only.

3

[ Regulatory Information

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-TX10

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The supplied interface cable must be used with the equipment in order to comply with the

limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

GB

4

For Customers in Europe

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

GB

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

GB

5

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

Notice for customers in the United Kingdom

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

GB

6

About water-proof, dust-proof, and shock-proof

performance of the camera

This camera is equipped to be water-proof, dust-proof and shock-proof.

Damage caused from misuse, abuse or failure to properly maintain the camera

is not covered by the limited warranty.

• This camera is water-proof/dust-proof equivalent to IEC60529 IP58. The

camera is operable up to a water depth of 5 m for 60 minutes.

• Do not subject the camera to pressurized water, such as from a tap.

GB

• Do not use in hot springs.

• Use the camera in the recommended operating water temperature range of

–10°C to +40°C (14°F to 104°F).

• Conforming to MIL-STD 810F Method 516.5-Shock standards, this product

has passed testing when dropped from a height of 1.5 m above a 5-cm thick

*

plywood board

.

*Depending on use conditions and circumstances, no guarantee is made regarding

damage to, malfunction of, or the water-proof performance of this camera.

• As for dust-proof/shock-proof performance, there is no guarantee that the

camera will not become scratched or dented.

• Sometimes water-proof performance is lost if the camera is subjected to a

strong shock such as from being dropped. We recommend the camera be

inspected at an authorized repair shop for a fee.

• Accessories supplied do not meet water-proof, dust-proof, and shock-proof

specifications.

Notes before using the camera under/near water

• Make sure that no foreign matter such as

sand, hair, or dirt gets inside the battery/

memory card cover or multi-connector

cover. Even a small amount of foreign

matter may lead to water entering the

camera.

GB

7

• Confirm that the sealing gasket and its

mating surfaces have not become scratched.

Even a small scratch may lead to water

entering the camera. If the sealing gasket or

its mating surfaces become scratched, take

the camera to an authorized repair shop to

1 Sealing gasket

have the sealing gasket replaced for a fee.

2 Surface contacting the

• If dirt or sand gets on the sealing gasket or

sealing gasket

its mating surfaces, wipe the area clean with

a soft cloth that will not leave behind any

fibers. Prevent the sealing gasket from becoming scratched by touching it

while charging a battery or using a cable.

• Do not open/close the battery/memory card cover or multi-connector cover

with wet or sandy hands or near water. There is a risk this will lead to sand or

water getting inside. Before opening the cover, perform the procedure

described in “Cleaning after using the camera under/near water”.

• Open the battery/memory card cover and multi-connector cover with the

camera completely dry.

• Always confirm that the battery/memory card cover and multi-connector

cover have been securely locked.

Notes on using the camera under/near water

• The touch panel may be activated by water splashes on the screen icons.

When using the camera under/near water, it is recommended that you hide

the icons by touching on the right side of the screen. Touch for a few

seconds to display the icons again.

• The touch panel cannot be operated underwater. Use the buttons of the

camera to perform shooting or playback operations.

• Do not subject the camera to shock such as from jumping into water.

• Do not open and close the battery/memory card cover or multi-connector

cover while under/near water.

• Use a separately available housing (Marine Pack) if going more than

5 meters under water.

• This camera sinks in water. Place your hand through the wrist strap to

prevent the camera from sinking.

• Faint, white, circular spots may appear in under-water flash photos due to

reflections off of floating objects. This is not a malfunction.

• Select (Underwater) in Scene Selection to shoot underwater with less

distortion.

GB

• If water drops or other foreign matter is present on the lens, you will be

unable to record clear images.

8

• Do not open the lens cover where the sand is whirling.

Cleaning after using the camera under/near

water

• Always clean the camera with water after use

within 60 minutes, and do not open the battery/

memory card cover before cleaning is finished.

Sand or water may get inside places where it

cannot be seen. If not rinsed, water-proof

GB

performance will be degraded.

• Allow the camera to sit in pure water poured into a cleaning bowl for about 5

minutes. Then, gently shake the camera, press each button, slide the zoom

lever or the lens cover inside the water, to clean away any salt, sand or other

matter lodged around the buttons or the lens cover.

• After rinsing, wipe away water drops with a soft cloth. Allow the camera to

dry completely in a shady location with good ventilation. Do not blow dry

with a hair dryer as there is a risk of deformation and/or degraded water-

proof performance.

• Wipe away water drops or dust on the memory card/battery cover or terminal

cover with a soft dry cloth.

• This camera is constructed to drain water. Water will drain from openings

around the ON/OFF (Power) button, zoom lever, and other controls. After

removing from water, place the camera on a dry cloth for a while to allow

water to drain.

• Bubbles may appear when the camera is placed under water. This is not a

malfunction.

• The camera body may become discolored if it comes in contact with

sunscreen or suntan oil. If the camera does come in contact with sunscreen or

suntan oil, quickly wipe it clean.

• Do not allow the camera to sit with salt water inside or on the surface. This

may lead to corrosion or discoloration, and degradation of water-proof

performance.

• To maintain the water-proof performance, we recommend that once a year

you take the camera to your dealer, or to an authorized repair shop, to have

the sealing gasket of the battery/memory card cover, or of the multi-

connector cover replaced for a fee.

GB

9

Inserting a memory card (sold separately)

Ensure the notched corner faces

correctly.

Open the cover.

1

Insert the memory card (sold separately).

2

• With the notched corner facing as illustrated, insert the memory card

until it clicks into place.

Close the cover securely, so that the yellow mark under

3

the slide lock is hidden.

• Closing the cover with the battery inserted incorrectly may damage the

camera.

x

Memory cards that you can use

Memory card For still images For movies

Memory Stick PRO Duo aa (Mark2 only)

A

Memory Stick PRO-HG Duo aa

Memory Stick Duo a —

SD memory card aa (Class 4 or faster)

B

SDHC memory card aa (Class 4 or faster)

SDXC memory card aa (Class 4 or faster)

• In this manual, products in A are collectively referred to as “Memory Stick Duo”

media, and products in B are collectively referred to as SD card.

GB

16

x

To remove the memory card/battery pack

Memory card: Push the memory card in once.

Battery pack: Slide the battery eject lever. Be sure not to drop the battery pack.

Note

• Never remove the memory card/battery pack when the access lamp (page 11) is lit.

This may cause damage to data in the memory card/internal memory.

GB

Setting the clock

Lens coverON/OFF (Power)

Lower the lens cover.

1

The camera is turned on. The power lamp lights up only when the camera

starts up.

• You can also turn on the camera by pressing the ON/OFF (Power)

button.

• It may take time for the power to turn on and allow operation.

Select a desired language.

2

Select the desired area following the instructions on the

3

screen, then touch [Next].

Set [Daylight Savings] or [Summer Time], [Date & Time

4

Format] and [Date & Time], then touch [Next].

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

Touch [OK].

5

GB

17

Select the desired display color, following the

6

instructions on the screen, then touch [OK].

When an [In-Camera Guide] introductory message is

7

appeared on the screen, touch [OK].

Read the waterproof precautions, then touch [OK].

8

Shooting still images/movies

Shutter button

MOVIE (Movie) button

Shooting still images

Press the shutter button halfway down to focus.

1

When the image is in focus, a beep sounds and the z indicator lights.

Press the shutter button fully down.

2

Shooting movies

Press the MOVIE (Movie) button to start recording.

1

• Use the W/T (zoom) lever to change the zoom scale.

Press the MOVIE button again to stop recording.

2

GB

18

Notes

• The sound of the lens and lever operating will be recorded when the zoom function

operates while shooting a movie. The sound of the MOVIE button operating may

also be recorded when movie recording is finished.

• Continuous shooting is possible for approximately 29 minutes at one time at the

camera’s default settings and when the temperature is approximately 25°C (77°F).

When movie recording is finished, you can restart recording by pressing the

MOVIE button again. Recording may stop to protect the camera depending on the

GB

ambient temperature.

Viewing images

(Playback)

Press the (Playback) button.

1

• When images on a memory card recorded with other cameras are played

back on this camera, the registration screen for the data file appears.

x

Selecting next/previous image

Touch (Next)/ (Previous) on the screen.

• To play back movies, touch (Playback) in the center of the screen.

• To zoom in, touch the still image being played back.

x

Deleting an image

1 Touch (Delete) t [This Image].

x

Returning to shooting images

Touch on the screen.

• You can also return to shooting mode by pressing the shutter button halfwaydown.

GB

19

In-Camera Guide

This camera contains an internal function guide. This allows you to search the

camera’s functions according to your needs.

Touch (In-Camera Guide).

1

• The mark will appear on the bottom right of the screen while viewing.

Select a search method from [In-Camera Guide].

2

Shoot/playback guide: Search for various operation functions in

shooting/viewing mode.

Icon guide: Search the function and meaning of displayed icons.

Troubleshooting: Search common problems and their solution.

Objective guide: Search functions according to your needs.

Keyword: Search functions by key words.

History: Display the last 10 items displayed in [In-Camera Guide].

GB

20

Introduction of other functions

Other functions used when shooting or playing back can be operated touching

the MENU on the screen. This camera is equipped with a Function Guide that

allows you to easily select from the functions. While displaying the guide, try

the other functions.

GB

x

Menu Items

Shooting

Movie shooting

Select movie recording mode.

scene

Easy Mode Shoot still images using minimal functions.

Flash Sets the flash settings.

Self-Timer Sets the self-timer settings.

Set the level of background defocus effect when

Defocus Effect

shooting in Background Defocus mode.

Still Image Size/

Select the image size and the quality for still images,

Panorama Image

panoramic images or movie files.

Size/Movie Size/

Movie Quality

Burst Settings Sets the burst shooting settings.

Macro Shoots beautiful close-up images of small subjects.

EV Adjust the exposure manually.

ISO Adjust the luminous sensitivity.

White Balance Adjust color tones of an image.

Underwater White

Adjusts the colors when shooting underwater.

Balance

GB

Focus Select the focus method.

21

Select the metering mode that sets which part of the

Metering Mode

subject to measure to determine the exposure.

Scene Recognition Set to automatically detect shooting conditions.

Soft Skin Effect Set the Soft Skin Effect and the effect level.

Set to automatically release the shutter when a smile is

Smile Shutter

detected.

Smile Detection

Set the Smile Shutter function sensitivity for detecting

Sensitivity

smiles.

Select to detect faces and adjust various settings

Face Detection

automatically.

Set to automatically shoot two images and select image

Anti Blink

in which the eyes are not blinking.

In-Camera Guide Search the camera’s functions according to your needs.

Viewing

Easy Mode Increase the text size on the screen for ease of use.

Date Select Selects the desired image to view by date.

Calendar Selects the date to be played back on Calendar.

Image Index Displays multiple images at the same time.

Slideshow Select a method of continuous playback.

Delete Delete an image.

Send by

Transfer data by closely aligning two products equipped

TransferJet

with TransferJet.

Paint Paints on a still image and saves it as a new file.

Retouch Retouch an image using various effects.

3D Viewing Set to play back images shot in 3D mode on a 3D TV.

View Mode Select the display format for images.

Display Burst

Select to display burst images in groups or display all

Group

images during playback.

Protect Protect the images.

Print (DPOF) Add a print order mark to a still image.

GB

Rotate Rotate a still image to the left or right.

22

Volume Adjusts the volume.

Sets whether or not to display the shooting data (Exif

Exposure data

data) of the currently displayed file on the screen.

Number of images

Sets the number of images displayed in the index screen.

in index

In-Camera Guide Search the camera’s functions according to your needs.

GB

x

Setting items

If you touch the MENU while shooting or during playback, (Settings) is

provided as a final selection. You can change the default settings on the

(Settings) screen.

Movie format/AF Illuminator/Grid Line/Digital Zoom/

Wind Noise Reduct./Scene Recog. Guide/Red Eye

Shooting Settings

Reduction/Blink Alert/Write Date

Beep/Panel Brightness/Language Setting/Display color/

Demo Mode/Initialize/CTRL FOR HDMI/Housing/USB

Connect Setting/USB Power Supply/LUN Setting/

Main Settings

Download Music/Empty Music/TransferJet/Eye-Fi/

Power Save

Format/Create REC.Folder/Change REC.Folder/Delete

Memory Card

REC.Folder/Copy/File Number

Tool

*

Area Setting/Date & Time Setting

Clock Settings

* If a memory card is not inserted, (Internal Memory Tool) will be displayed and

only [Format] can be selected.

GB

23

Number of still images and recordable time of

movies

The number of still images and recordable time may vary depending on the

shooting conditions and the memory card.

x

Still images

(Units: Images)

Capacity

Internal memory Memory card

Size

Approx. 19 MB 2 GB

16M 3 335

VGA 98 9600

16:9(12M) 3 355

x

Movies

The table below shows the approximate maximum recording times. These are

the total times for all movie files. Continuous shooting is possible for

approximately 29 minutes. The maximum size of an MP4-format movie file is

up to approximately 2 GB.

(h (hour), m (minute))

Capacity

Internal memory Memory card

Size

Approx. 19 MB 2 GB

AVC HD 24M (FX) — 10 m

(10 m)

AVC HD 9M (HQ) — 25 m

(15 m)

MP4 12M — 15 m

MP4 3M — 1 h 10 m

The number in ( ) is the minimum recordable time.

• The recordable time of movies varies because the camera is equipped with VBR

(Variable Bit Rate), which automatically adjusts image quality depending on the

shooting scene. When you record a fast-moving subject, the image is clearer but

the recordable time is shorter because more memory is required for recording.

The recordable time also varies depending on the shooting conditions, the subject

or the image quality/size settings.

GB

24

Notes on using the camera

Functions built into this camera

• This manual describes each of the functions of TransferJet compatible/

incompatible devices, 1080 60i-compatible devices and 1080 50i-compatible

devices.

To check if your camera supports the TransferJet function, and whether it is a

1080 60i-compatible device or 1080 50i-compatible device, check for the

GB

following marks on the bottom of the camera.

TransferJet-compatible device:

(TransferJet)

1080 60i-compatible device: 60i

1080 50i-compatible device: 50i

• Do not watch 3D images shot with this camera for extended periods of time on

3D-compliant monitors.

• When you view 3D images shot with this camera on a 3D-compliant monitors, you

may experience discomfort in the form of eye strain, fatigue, or nausea. To prevent

these symptoms, we recommend that you take regular breaks. However, you need

to determine for yourself the length and frequency of breaks you require, as they

vary according to the individual. If you experience any type of discomfort, stop

viewing the 3D images until you feel better, and consult a physician as necessary.

Also refer to the operating instructions supplied with the device or software you

have connected or are using with this camera. Note that a child's eyesight is still at

the development stage (particularly children below the age of 6).

Consult a pediatrician or ophthalmologist before letting your child view 3D

images, and make sure he/she observes the above precautions when viewing such

images.

On use and care

Avoid rough handling, disassembling, modifying, physical shock, or impact such as

hammering, dropping, or stepping on the product. Be particularly careful of the lens.

Notes on recording/playback

• Before you start recording, make a trial recording to make sure that the camera is

working correctly.

• Do not aim the camera at the sun or other bright light. It may cause the

malfunction of the camera.

• If moisture condensation occurs, remove it before using the camera.

• Do not shake or strike the camera. It may cause a malfunction and you may not be

able to record images. Furthermore, the recording media may become unusable or

image data may be damaged.

Do not use/store the camera in the following places

• In an extremely hot, cold or humid place

In places such as in a car parked in the sun, the camera body may become

GB

deformed and this may cause a malfunction.

25