Panasonic DMWMCFT5E: 6 Inspect the O-ring one last time.
6 Inspect the O-ring one last time.: Panasonic DMWMCFT5E
6 Inspect the O-ring one last time.
Check the following one more time:
• There is no dirt sticking to the O-ring.
• The O-ring has not come out.
• The O-ring is not twisted.
• There are no scratches or squashed parts on the O-ring.
Thoroughly wipe any grease off your hands with a dry cloth.
Afterwards wash thoroughly with fresh water.
7 Close the buckle.
•
Check that no foreign materials are sticking to the outer surface of the O-
ring or the buckle on the front case and then close the Case.
Notes
• To keep the Case completely airtight, do not scratch the surface of the O-ring that
comes into contact with the sides of the Case.
• Never use an O-ring that has been scratched or damaged by dirt etc. This will
cause water leakage.
• Each time you use the Case, remove the O-ring and check that there is no dirt,
sand, hair or other foreign materials in the O-ring groove and then apply a thin coat
of grease (supplied). If you apply too much grease, dirt and the dust may stick to
the O-ring causing water leakage.
• Be sure to bring a spare O-ring in case the O-ring that you are using becomes
damaged or scratched.
(ENG) VQT4V83
11
DMW-MCFT5_PP&E-VQT4V83.book 11 ページ ２０１３年１月１６日 水曜日 午前１１時３５分
DMW-MCFT5_PP&E-VQT4V83.book 12 ページ ２０１３年１月１６日 水曜日 午前１１時３５分
Checking the Case is Waterproof
After setting the O-ring, check that no water leaks into the Case by
submerging it in a water tank, bath tub etc. for about 3 minutes before
attaching a digital camera.
• Do not use the Case in water over 40 °C/104 °F. The heat may damage the Case
or cause water leakage.
• Carry out the same test after attaching the digital camera to the Case. (P15)
Notes
• If bubbles rise from the Case when it is submerged in water or there is water inside
the Case when you take it out of the water, there is water leakage. In these cases,
consult your dealer.
• If water leaks into the Case while you are using it and the digital camera is
submerged in water, remove the battery immediately. Hydrogen gas can cause
burning or explosion if there is a fire nearby.
• If you dive quickly while holding the Case or throw the Case from a ship into the
sea, some water leakage may occur because of high pressure. This is not a
malfunction of the Case. Always dive slowly into the water.
• The Case is designed to be used at a depth of up to 45 m/148 feet. If you dive
deeper than 45 m/148 feet, part of the Case may be damaged beyond repair.
• When closing the Case, be careful that no foreign materials get caught between
the O-ring and the O-ring groove. Even one strand of hair or one grain of sand can
cause water leakage.
12
VQT4V83 (ENG)
Оглавление
- DMW-MCFT5
- 1 Loosen the O-ring with your fingers to remove it.
- 2 Check the O-ring.
- 4 Apply the grease (supplied).
- 6 Inspect the O-ring one last time.
- 1 Push 2 up with your finger while sliding 1 to open the
- 3 Insert the silica gel (supplied).
- 5 After you have attached the digital camera, check one
- 1 Turn the camera on. 2 Set to the [Advanced Underwater Mode]. 3 Aim the AF area on the LCD monitor at the subject you
- 1 Submerge the Case in fresh water for about 30 minutes or
- 3 Open the rear of the case to remove the digital camera.
- 1 Wash the outside of the Case with water.
- 1 Desserrez le joint torique avec vos doigts pour l’enlever.
- 2 Vérifiez le joint torique.
- 4 Appliquez la graisse (fournie).
- 6 Vérifiez le joint torique une dernière fois.
- 1 Appuyez sur 2 avec votre doigt tout en faisant glisser 1
- 3 Insérez le gel de silice (fourni).
- 5 Après avoir installé l’appareil photo, vérifiez une fois de
- 1 Mettez l’appareil photo en marche. 2 Réglez à [Mode sous-marin avancé]. 3 Dirigez la zone MPA de l’écran ACL sur le sujet que vous
- 1 Immergez le boîtier dans de l’eau douce pendant environ
- 3 Ouvrez le couvercle arrière pour retirer l’appareil photo
- 1 Lavez l’extérieur du boîtier avec de l’eau.
- 1 Den O-Ring zum Entfernen mit den Fingern lösen.
- 2 Prüfen des O-Rings.
- 4 Tragen Sie das Fett auf (beiliegend).
- 6 Letzte Überprüfung des O-Rings.
- 1 Drücken Sie 2 mit dem Finger nach oben, während 1
- 3 Legen Sie das Kieselgel ein (beiliegend).
- 1 Schalten Sie die Kamera ein. 2 Richten Sie den [Erweit. Unterwassermodus] ein. 3 Den AF-Bereich auf dem LCD-Monitor auf das
- 1 Das Gehäuse ca. 30 Minuten oder mehr in Süßwasser
- 3 Die Geräterückseite öffnen, um die Digitalkamera zu
- 1 Die Außenseite des Gehäuses mit Wasser abwaschen.
- 1 Afloje el anillo tórico con sus dedos para quitarlo.
- 2 Controle el anillo tórico.
- 4 Aplique la grasa (suministrada).
- 6 Controle el anillo tórico una última vez.
- 1 Empuje hacia arriba 2 con su dedo, mientras hace
- 3 Inserte el silicagel (suministrado).
- 5 Después de unir la cámara digital, compruebe una vez
- 1 Encienda la cámara. 2 Fije en [Modo submarino avanzado]. 3 Dirija el área AF en el monitor LCD hacia el sujeto que
- 1 Sumerja el estuche en agua fresca durante 30 minutos o
- 3 Abra la parte trasera del estuche para quitar la cámara
- 1 Lave la parte externa del estuche con agua.
- 1 Allentare l’O-ring con le dita per rimuoverlo.
- 2 Controllare l’O-ring.
- 4 Applicare il grasso (in dotazione).
- 6 Controllare un’ultima volta l’O-ring.
- 1 Spingere 2 verso l’alto con un dito, e
- 3 Inserire il silica gel (in dotazione).
- 1 Accendere la fotocamera. 2 Impostare [Modalità subacquea avanzata]. 3 Inquadrare il soggetto che si desidera mettere a fuoco
- 1 Immergere la custodia in acqua dolce per circa 30 minuti
- 3 Aprire la copertura posteriore per rimuovere la
- 1 Lavare l’esterno della custodia con acqua.
- 1 用手指將 O 形環鬆開，然後取下。
- 2 檢查 O 形環。
- 4 塗抹潤滑油（提供）。
- 6 最後檢查 O 形環。
- 1 在滑動 1 的同時，用手指上推 2 打開盒扣。 2 將數位相機裝入盒子。
- 3 插入硅膠（提供）。
- 5 裝入數位相機後，請再次檢查盒子是否漏水。 (P122)
- 1 打開相機。 2 設定為 [進階潛水模式 ]。 3 瞄準想對焦的目標，將其置於 LCD 顯示屏上的 AF 區域中。 4 固定焦點進行拍攝。
- 1 不要取出數位相機，將盒子浸沒在清水中約 30 分鐘或更長時間
- 3 打開後封蓋取出數位相機。
- 1 用水沖洗盒子的外部。
- 1 Для снятия уплотнительного кольца ослабьте его
- 2 Проверка уплотнительного кольца.
- 4 Нанесите смазку (входит в комплект поставки).
- 6 Проверьте уплотнительное кольцо еще раз.
- 1 Для открытия защелки поднимите деталь 2 пальцем,
- 3 Вставьте силикагель (входит в комплект поставки).
- 5 После установки цифровой камеры еще раз
- 1 Включите камеру.
- 1 Погрузите футляр в пресную воду не менее чем на
- 3 Чтобы вынуть цифровую камеру, откройте заднюю
- 1 Промойте наружную поверхность футляра водой.
