Panasonic ES6003: инструкция
Раздел: Бытовая, кухонная техника, электроника и оборудование
Тип: Прочие персональные приборы
Инструкция к Прочим персональным приборам Panasonic ES6003
P00-05ES6003/6002EU 06.03.09 14:17 ページ1
Wet/Dry Rechargeable Shaver
Operating Instructions
Model No. ES6003/ES6002
Panasonic Electric Works Wanbao (Guangzhou) Co., Ltd.
Wanbao Base Shiguang Road, Panyu District, Guangzhou,
Guangdong, 511495 CHINA
B
Before operating this unit, please read these instructions completely.
No.1 EN, GE, FR, IT, DU, SP, DA, PT, NW, SW, FI, PL, CZ, HU, RO, RU, TK, UA (
欧州
)
Printed in China
32
A
B
C
D
E
F
H
G
I
J
K
L
MN
1
2
3
4
(b)
(a)
charge
P00-05ES6003/6002EU 06.03.09 14:17 ページ2
5
7
6
8
READ ALL INSTRUCTIONS BE-
Before use
FORE USE.
This Wet/Dry shaver can be used for
wet shaving with shaving lather or for
Charging
dry shaving. You can use this water-
(see fig. 2)
tight shaver in the shower and clean
When charging the shaver for the first
it in water. The following is the sym-
time or when it has not been in use
bol of Wet shaver. The symbol means
for more than 6 months, charge it for
that hand-held part may be used in
at least 16 hours before use.
a bath or shower.
Connect the power cord to the
shaver, and plug the adaptor to an
AC outlet.
In some areas, a special plug adaptor
may be required.
Treat yourself to wet lather shaves
The charge indicator lamp will glow
for at least three weeks and notice
red when the shaver is being
the difference. Your Panasonic Wet/
charged. It will stay on until the
Dry shaver requires a little time to get
power cord is disconnected from the
used to because your skin and beard
AC outlet.
need about a month to adjust to any
You can fully charge the shaver in 12
new shaving method.
hours if it seems to be losing speed.
A full charge will supply enough
Parts identification
power for approx. 14 shaves
(see fig. 1)
(3 minutes per shave for a normal
A Protective cap
beard).
B System outer foil
Even if not fully charged, an 8-hour
C System outer foil release but-
charge will supply enough power for
tons
about 10 shaves.
D Foil frame
Using your shaver
E Inner blades
F Foil frame release buttons
Caution – The system outer foil is
very thin and can be damaged if
G Charge indicator lamp
handled improperly. Before each
H On/Off switch
use, always check the foil for dam-
I Trimmer
age. To avoid personal injury, do not
J Trimmer handle
use if the foil or other parts of the
shaving head is damaged.
K Adaptor
L Power cord
Depress the switch lock button and
M Cleaning brush
slide the On/Off switch upward to turn
the shaver on.
N Soft case
9 10
11
54
c
b
e
d
f
a
g
h
d
P00-05ES6003/6002EU 06.03.09 14:17 ページ4
(A) (B)
Index
ENGLISH Page 05
SVENSKA Sid 51
DEUTSCH Seite 10
SUOMI Sivu 56
FRANÇAIS Page 16
POLSKI Strona 61
ITALIANO Pagina 21
ČESKY Strona 67
NEDERLANDS Pagina 26
MAGYAR Oldal 72
ESPAÑOL Pagina 31
ROMANA Pagina 78
DANSK Side 36
êìëëäàâ
ëÚ‡Ìˈ‡
83
PORTUGÊS Pagina 41
TÜRKÇE Sayfa 89
NORSK Side 46
ì͇ªÌҸ͇
ëÚÓ¥Ì͇
94
Hold the shaver at a right angle (90°)
Cleaning your shaver
to your skin (see fig. 3). Start out
(see fig. 6)
shaving by applying gentle pressure
to your face. Stretch your skin with
Warning – To prevent electric
your free hand and move the shaver
shock or personal injury, discon-
back and forth in the direction of your
nect the power cord from the
beard. You may gently increase the
shaver before cleaning with water.
amount of pressure as your skin be-
For cleanliness and convenience, we
comes accustomed to this shaver.
recommend that you clean your
Applying excessive pressure does
shaver with water and a liquid hand
not provide a closer shave.
soap. Regular cleaning will keep your
System outer foil
shaver in good condition while pre-
(see fig. 4)
venting odors or bacteria from devel-
System outer foil has a slit blade (a)
oping, and maintain the cutting per-
between 2 foils (b). They move up
formance.
and down independently to follow the
With the system outer foil in place,
contours of your face.
apply some hand soap onto the outer
The slit blade catches and cuts
foil.
longer and lying hairs easily.
Turn the shaver on and pour some
water over the outer foil.
For wet shaving
After about 10-20 seconds, turn the
Put a thin layer of shaving foam
shaver off.
on your face which works as a lu-
Remove the foil frame and clean
bricator. Shaving foam is the most
it with running water.
suitable among many other shav-
Wipe off any moisture from the
ing aids (gel, soap, cream, etc.).
shaver with a dry cloth and remove
Do not put a thick layer of shaving
the protective cap to allow the sys-
foam as it may affect shaver’s per-
tem outer foil to dry completely.
formance. If the shaving head is
clogged with foam, simply rinse
Brush cleaning
it under running water.
Squeeze the foil frame release but-
tons and lift the foil frame upward to
Using the trimmer
remove it (see fig. 8). Remove the in-
(see fig. 5)
ner blades one at a time by grasping
Slide the trimmer handle up to open
it firmly at both ends and pulling it
the trimmer.
straight away from the shaver. Clean
Place the trimmer at a right angle to
the outer foils, the shaver body and
your skin and move it downward to
the trimmer with the long brush (see
trim sideburns.
fig. 9). Clean the inner blades with
the short brush by moving it in the
direction in fig. 10 (A). Do not move
the brush in the direction in fig. 10
For environmental protec-
(B), as it will damage the inner blade,
tion and recycling of
and its cutting performance. Do not
use the short brush to clean the outer
materials
foils.
This shaver contains Nickel-Metal
Hydride batteries.
Replacing shaving head
Please make sure that the batteries
components
are disposed of at an officially as-
signed location, if there is one in your
It is recommended that you replace
country.
the system outer foil at least once a
year and the inner blade at least once
How to remove the built-in
every 2 years to maintain your
rechargeable battery before
shaver’s cutting performance.
disposal of the shaver
(see fig. 11)
Replacing the system outer foil
(see fig. 7)
WARNING:
Squeeze the system outer foil re-
Do not attempt to replace the bat-
lease buttons and lift the system
tery for the purpose of reusing the
outer foil upward to remove it. To in-
shaver. This could result in the risk
sert the new system outer foil, press
of fire or electric shock.
down until it snaps into place.
The battery in this shaver is not
Replacing the inner blades
intended to be replaced by con-
(see fig. 8)
sumers. However, the battery
Squeeze the foil frame release
may be replaced at an authorized
buttons and lift the foil frame
service center. The procedure
upward to remove it. Remove the
described below is intended only
inner blade one at a time by
for removal of the rechargeable
grasping it firmly at both ends
battery for the purpose of proper
and pulling straight away from
disposal.
the shaver.
1. Disconnect the power cord from
Do not touch the metal parts of inner
the shaver when removing the
blades.
battery.
To insert the new inner blade, hold
2. Remove the bottom cover screw
the blade one at a time at both ends
(a).
and press downward until it snaps
3. Remove the bottom cover (b).
into the shaver.
4. Slide the side panels (c) and re-
move it.
5. Remove the six housing screws
(d).
6. Remove the trimmer handle (e).
7. Remove the two screws (f).
P06-99ES6003/6002EU 06.03.09 14:18 ページ6
76
