Panasonic ES8162: инструкция

It shows the remaining battery ca-

[for ES8161]

pacity from 0% to 100%, in 10% in-

The charge status lamp will glow

crements.

when the shaver is being charged. It

When the charging is completed, it

will blink when the charging is com-

will indicate “100%” and the backlight

pleted (see fig. 2 (F)).

of LCD display will flash once in

You can fully charge the shaver in 1

about 1 second. It will flash once in

hour if the low battery indicator blinks

about 2 seconds for 10 minutes af-

(see fig. 2 (E)).

ter charging is completed (see fig. 2

The unit can be used once or twice

(B)).

more after the low battery indicator

You can fully charge the shaver in 1

starts to blink.

hour if the LCD display shows 10%

and lower.

A full charge will supply enough

The plug symbol blinks in the LCD

power for approx. 14 shaves (3 min-

display when the remaining battery

utes per shave for a normal beard).

capacity is 10% and less.

Before travelling, charge it fully for 1

The unit can be used once or twice

hour if you will not be taking the adap-

more after the LCD display starts to

tor with you.

show 10%. (Differs depending on the

In case your shaver is without charge,

use situation.)

you may quick charge it for 1 shave

in about 5 minutes.

[for ES8162]

The charge status lamp will glow

Charge with charging

when the shaver is being charged.

stand

100 to 20 of the battery capacity

(see fig. 1 (B))

monitor will all illuminate and the

To charge with the charging stand,

charge status lamp will blink after

connect the power cord to the charg-

charging is completed (see fig. 2 (C)).

ing stand. Place the shaver into the

10 minutes after charging is com-

stand, and plug the adaptor to the

pleted, the battery capacity monitor

AC outlet.

will extinguish and the charge status

You can always store your shaver in

lamp will continue to blink (see fig. 2

the charging stand to maintain full

(D)).

battery capacity. This shaver cannot

You can fully charge the shaver in 1

be overcharged.

hour if the LED display shows 20%.

The battery capacity monitor indi-

cates the charge remaining in the

battery. The unit can be used once

or twice more after the “20” starts to

blink. (Differs depending on the use

situation.)

8

Cleaning your shaver

out the system outer foil.

It is recommended to clean your

(see fig. 7)

shaver with the “sonic” vibration

Warning – To prevent electric

cleaning when the tap symbol (a)

shock or personal injury, discon-

appears in LCD (ES8163).

nect the power cord from the

shaver before cleaning with water.

Brush cleaning

Squeeze the foil frame release but-

For cleanliness and convenience, we

tons and lift the foil frame upward to

recommend that you clean your

remove it (see fig. 9). Remove the

shaver with water and a liquid hand

inner blades one at a time by grasp-

soap. Regular cleaning will keep your

ing it firmly at both ends and pulling

shaver in good condition while pre-

it straight away from the shaver.

venting odors or bacteria from devel-

Clean the outer foils, the shaver body

oping, and maintain the cutting per-

and the trimmer with the long brush

formance.

(see fig. 10). Clean the inner blades

With the system outer foil in place,

with the short brush by moving it in

apply some hand soap onto the outer

the direction in fig. 11 (A). Do not

foil.

move the brush in the direction in fig.

Push and hold the On/Off switch

11 (B), as it will damage the inner

more than 2 seconds to activate the

blade, and its cutting performance.

turbo mode for “sonic” vibration

Do not use the short brush to clean

cleaning.

the outer foils.

At the same time, the “sonic” clean-

ing symbol appears in the LCD dis-

Replacing shaving head

play (ES8163), or the lamps of the

components

Battery capacity monitor (ES8162),

It is recommended that you replace

or Low battery indicator/Charge sta-

the system outer foil at least once a

tus lamp (ES8161) will flash around

year and the inner blade at least once

randomly.

every 2 years to maintain your shav-

Pour some water over the outer foil.

er’s cutting performance.

After about 20 seconds, it will be

automatically turned off, or you can

Replacing the system outer foil

turn it off by pushing the On/Off

(see fig. 8)

switch.

Squeeze the system outer foil re-

Remove the system outer foil and

lease buttons and lift the system

push the On/Off switch more than 2

outer foil upward to remove it. To in-

seconds to activate the turbo mode

sert the new system outer foil, press

for “sonic” vibration cleaning and

down until it snaps into place.

clean it with running water.

Wipe off any moisture from the

shaver with a dry cloth and dry it with-

10