Panasonic ES7036: инструкция
Раздел: Бытовая, кухонная техника, электроника и оборудование
Тип: Прочие персональные приборы
Инструкция к Прочим персональным приборам Panasonic ES7036
Wet/Dry Rechargeable Shaver
Operating Instructions
Model No. ES7038/ES7036
Matsushita Electric Works Wanbao (Guangzhou) Ltd.
Wanbao Base, Zhong Cun Pan Yu, GuangDong 511495, China
B
Before operating this unit, please read these instructions completely.
No.1 EN, GE, FR, IT, DU, SP, DA, PT, NW, SW, FI, PL, CZ, HU, RO, RU, TK, UA (
欧州
)
Printed in China
P000-005ES703836EU 05.07.26 3:05 ページ1
32
high
mid
recharge
low
charge
status
A
B
C
L
D
M
E
F
K
G
[ES7038] [ES7036]
H
a
J
H
b
H
H
c
charge
I
status
N
O
PQ
1
2
3
4
(b)
(a)
high
high
mid
mid
low
low
charge
charge
status
status
recharge
recharge
charge
charge
status
status
[ES7038]
(A) (B)
[ES7036]
(C) (D)
5
7
6
8
P000-005ES703836EU 05.07.26 3:05 ページ2
K On/Off switch
Before use
This Wet/Dry shaver can be used for
L Trimmer
wet shaving with shaving lather or for
M Trimmer handle
dry shaving. You can use this water-
N Adaptor
tight shaver in the shower and clean
O Power cord
it in water. The following is the sym-
bol of Wet shaver. The symbol means
P Cleaning brush
that hand-held part may be used in
Q Soft case
a bath or shower.
READ ALL INSTRUCTIONS BE-
FORE USE.
Charging
When charging the shaver for the first
Treat yourself to wet lather shaves
time or when it has not been in use
for at least three weeks and notice
for more than 6 months, charge it for
the difference. Your Panasonic Wet/
at least 8 hours before use.
Dry shaver requires a little time to get
Connect the power cord to the
used to because your skin and beard
shaver, and plug the adaptor to an
need about a month to adjust to any
AC outlet.
new shaving method.
The shaver will be adjusted automati-
cally to voltages between 100-240V
Parts identification
AC.
(see fig. 1)
In some areas, a special plug adap-
A Protective cap
tor may be required.
B System outer foil
[for ES7038]
C System outer foil release but-
The charge status lamp will glow
tons
when the shaver is being charged.
D Foil frame
The battery capacity monitor will all
illuminate and the charge status lamp
E Inner blades
will blink after charging is completed
F Foil frame release buttons
(see fig. 2 (A)).
G LED display
10 minutes after charging is
H Battery capacity monitor
completed, the battery capacity
monitor will extinguish and the
H-a high
charge status lamp will continue to
H-b mid
blink (see fig. 2 (B)).
H-c low
You can fully charge the shaver in
I Charge status lamp
1 hour if the LED display shows “low”
(low).
J Low battery indicator
5
9 10
11
54
e
b
c
f
a
d
g
e
(A) (B)
Index
ENGLISH Page 5
SVENSKA Sid 57
DEUTSCH Seite 10
SUOMI Sivu 62
FRANÇAIS Page 16
POLSKI Strona 67
ITALIANO Pagina 22
ČESKY Strona 73
NEDERLANDS Pagina 28
MAGYAR Oldal 79
ESPAÑOL Pagina 34
ROMANA Pagina 85
DANSK Side 40
êìëëäàâ
ëÚ‡Ìˈ‡
91
PORTUGÊS Pagina 46
TÜRKÇE Sayfa 97
NORSK Side 52
ì͇ªÌÒ¸ÍËÈ
ëÚÓ¥Ì͇
103
P000-005ES703836EU 05.07.26 3:05 ページ4
The battery capacity monitor indi-
Hold the shaver at a right angle (90°)
cates the charge remaining in the
to your skin (see fig. 3). Start out
battery in 3 levels “high/mid/low”
shaving by applying gentle pressure
(high/mid/low). The unit can be used
to your face. Stretch your skin with
once or twice more after the “low”
your free hand and move the shaver
(low) starts to blink. (Differs depend-
back and forth in the direction of your
ing on the use situation.)
beard. You may gently increase the
amount of pressure as your skin be-
[for ES7036]
comes accustomed to this shaver.
The charge status lamp will glow
Applying excessive pressure does
when the shaver is being charged. It
not provide a closer shave.
will blink when the charging is com-
System outer foil
pleted (see fig. 2 (D)).
(see fig. 4)
You can fully charge the shaver in 1
System outer foil has a slit blade (a)
hour if the low battery indicator blinks
between 2 foils (b). They move up
(see fig. 2 (C)).
and down independently to follow the
The unit can be used once or twice
contours of your face.
more after the low battery indicator
The slit blade catches and cuts
starts to blink.
longer and lying hairs easily.
A full charge will supply enough
For wet shaving
power for approx. 14 shaves (3 min-
Put a thin layer of shaving foam
utes per shave for a normal beard).
on your face which works as a lu-
Before travelling, charge it fully for 1
bricator. Shaving foam is the most
hour if you will not be taking the adap-
suitable among many other shav-
tor with you.
ing aids (gel, soap, cream, etc.).
In case your shaver is without charge,
Do not put a thick layer of shaving
you may quick charge it for 1 shave
foam as it may affect shaver’s per-
in about 5 minutes.
formance. If the shaving head is
clogged with foam, simply rinse
Using your shaver
it under running water.
Caution – The system outer foil is
very thin and can be damaged if
Using the trimmer
handled improperly. Before each
(see fig. 5)
use, always check the foil for dam-
Slide the trimmer handle up to open
age. To avoid personal injury, do not
the trimmer.
use if the foil or other parts of the
Place the trimmer at a right angle to
shaving head is damaged.
your skin and move it downward to
Depress the switch lock button and
trim sideburns.
slide the On/Off switch upward to turn
the shaver on.
6
Cleaning your shaver
direction in fig. 10 (A). Do not move
the brush in the direction in fig. 10
(see fig. 6)
(B), as it will damage the inner blade,
Warning – To prevent electric
and its cutting performance. Do not
shock or personal injury, discon-
use the short brush to clean the outer
nect the power cord from the
foils.
shaver before cleaning with water.
Replacing shaving head
For cleanliness and convenience, we
components
recommend that you clean your
It is recommended that you replace
shaver with water and a liquid hand
the system outer foil at least once a
soap. Regular cleaning will keep your
year and the inner blade at least once
shaver in good condition while pre-
every 2 years to maintain your shav-
venting odors or bacteria from devel-
er’s cutting performance.
oping, and maintain the cutting per-
formance.
Replacing the system outer foil
With the system outer foil in place,
(see fig. 7)
apply some hand soap onto the outer
Squeeze the system outer foil re-
foil.
lease buttons and lift the system
Turn the shaver on and pour some
outer foil upward to remove it. To in-
water over the outer foil.
sert the new system outer foil, press
After about 10-20 seconds, turn the
down until it snaps into place.
shaver off.
Replacing the inner blades
Remove the foil frame and clean
(see fig. 8)
it with running water.
Squeeze the foil frame release
Wipe off any moisture from the
buttons and lift the foil frame
shaver with a dry cloth and remove
upward to remove it. Remove the
the protective cap to allow the sys-
inner blade one at a time by
tem outer foil to dry completely.
grasping it firmly at both ends
and pulling straight away from
Brush cleaning
the shaver.
Squeeze the foil frame release but-
Do not touch the metal parts of inner
tons and lift the foil frame upward to
blades.
remove it (see fig. 8). Remove the in-
To insert the new inner blade, hold
ner blades one at a time by grasping
the blade one at a time at both ends
it firmly at both ends and pulling it
and press downward until it snaps
straight away from the shaver. Clean
into the shaver.
the outer foils, the shaver body and
the trimmer with the long brush (see
fig. 9). Clean the inner blades with
the short brush by moving it in the
7
76
P006-039ES703836EU 05.07.26 3:09 ページ6
