Panasonic HFS45150E: Supplied Accessories Attaching/Detaching the Lens

Supplied Accessories

Attaching/Detaching the Lens

[Inspection to be performed when you unpack

≥ Refer also to the camera’s operating instructions

the unit]

for attaching and detaching the lens.

When removing the unit from its packing box, check

∫ Attaching the Lens

that the main unit and the supplied accessories are

≥ Check that the camera is turned off.

there and also check their external appearance and

1 Turn the lens rear cap to

functions to verify that they have not sustained any

detach it.

damage during distribution and transportation.

A: Lens Rear Cap

If you discover any trouble, contact your vendor

before using the product.

Product numbers correct as of September 2012.

These may be subject to change.

2 Align the lens fitting

marks B (red marks) on

the camera body and the

lens and then rotate the

lens in the direction of

the arrow until it clicks.

• Do not press the lens release

1 Lens Hood

button C when you attach a lens.

2 Lens Cap

• Do not try to attach the lens when holding it at an

3 Lens Rear Cap

angle to the camera body as the lens mount may

(The lens rear cap and lens cap are attached to

get scratched.

the interchangeable lens at the time of purchase.)

• Check that the lens is attached correctly.

5

VQT4J90

VQT4J90_E.book 5 ページ ２０１２年８月８日　水曜日　午後４時５０分

VQT4J90_E.book 6 ページ ２０１２年８月８日　水曜日　午後４時５０分

∫ Detaching the Lens

∫ Attaching the Lens Hood

≥ Check that the camera is turned off.

(Supplied Accessory)

While pressing on the

1 Align the fitting mark E on the lens

lens release button D,

hood with the mark on the tip of the

rotate the lens toward the

lens.

arrow until it stops and

2 Turn the lens hood in the direction of

then remove.

the arrow until it stops, and align the

• Attach the lens rear cap so

stop mark F on the lens hood with

that the lens contact point does not get

the mark on the tip of the lens.

scratched.

• Attach the body cap to the camera so no dirt or

dust will get inside the main unit.

∫ Attaching and Detaching the Lens Cap

Pinch the lens cap as shown in the figure

to attach or detach.

≥ Be careful not to lose

the lens cap.

6

VQT4J90

VQT4J90_E.book 7 ページ ２０１２年８月８日　水曜日　午後４時５０分

∫ Temporarily Storing the Lens Hood

∫ Attaching Filters

≥ Vignetting may occur if using 2 or more

1 Turn the lens hood in the direction of the

MC protectors (optional: DMW-LMC52),

arrow to detach it.

PL filters (optional: DMW-LPL52) or ND filters

(optional: DMW-LND52), or if using thick

protectors and/or filters.

≥ The filter may become impossible to remove if

excessively tightened, so please refrain from

tightening it too strongly.

≥ It is possible to attach the lens cap with the filter

already attached.

2 Reverse the lens hood and then attach it

≥ You cannot attach a conversion lens or adaptor to

in the same way as shown previously.

this lens. A filter may be used, but attaching any

≥ When taking pictures with

other element may cause damage to the lens.

the flash with the lens hood

attached, the lower portion of

the screen may turn dark

(vignetting effect) and the

control of the flash may be

disabled because the photo

flash may be obscured by the lens hood. We

recommend detaching the lens hood.

≥ When using the AF assist lamp in the dark, detach

the lens hood.

7

VQT4J90