Vitek VT-1671: ENGLISH

Vt-1671.qxd 10.01.05 11:28 Page 9

ENGLISH

HOW TO USE OF YOUR MEAT MINCER

 Wash all the parts in hot soapy water and allow to

 This meat mincer is intended to mince boneless

dry. Never put the parts in the dishwasher.

meat for household use only. After assembling the

 Wipe the base unit (5) with a damp cloth.

appliance, place it on a flat dry surface.

 Wipe the mincer screen plate and blade with salad

 Please ensure that the ventilation openings on the

oil before storing to prevent air corrosion.

base unit are not blocked.

 Kebbe attachments (18, 19) and sausage attach-

 Make sure that local mains voltage corresponds to

ments (16, 17) shall be stores inside the pusher (1).

the operational voltage of the appliance.

Fig. 18.

 Connect the plug to the mains outlet.

 The power cord shall be stored in a special com-

 Place the food tray carefully. Put a bowl or another

partment at the bottom of the base unit. Fig. 16.

container under the screen plate through which the

mincemeat flows out.

ATTENTION

 Before mincing make sure that the meat has thawed

 Always ensure that the bones and excess fat are

completely.

removed from the meat before mincing.

 Remove bones and excess far. Rinse the meat and

 Always use only the pusher provided. Never use

cut it into cubes or stripes to fit the food funnel.

Your fingers or kitchen utensils

 Switch on the mincer by pressing the ON/OFF but-

 Never immerse the base unit in water or other liq-

ton (5).

uids.

 Slowly food the meat pieces into the food funnel

 Never fix screen plates (10, 11, 14) and the blade

using the pusher (1).

(13) when using sausage or kebbe attachments.

 Do not apply excess force to push the food through

 Do not try to mince food with hard fiber like ginger

- you may damage the appliance. Never use fingers

or horseradish.

or kitchen utensils to push the food through.

 To avoid blocks and jams inside the feeder screw,

 There are chances that the meat will get stuck in the

never apply excessive force.

feeder screw during operation. In such case, use

 If the unit gets blocked due to hard foods lodged

the reverse speed. To do so switch off the appliance

onto the feeder screw or cutting blade, immediate-

by pressing the ON/OFF button (5), let the motor

ly switch off the appliance and remove the ingredi-

stop completely and press the REV button (7) (Fig.

ent before starting again.

17), then resume operation after 6-10 seconds.

 When the circuit breaker activates, do not switch on

 Do not run the appliance for more than 15 minutes

the appliance immediately. Wait for about 60 sec-

continuously. After 15 minutes of continuous use,

onds and start again using smaller force to push the

let the appliance cool down to room temperature

food through.

before further use.

 When switching to the Reverse mode or vice versa,

 Once the task is over, switch off the mincer, and

wait for about 6 seconds to assure that the motor

unplug before disassembling.

has stopped completely.

SCREEN PLATES (10, 11,14)

SPECIFICATIONS:

The appliance is completed with three screen plates -

Power requirement: 220Â-230 V ~ 50-60 Hz

for coarse, medium and fine cutting.

Maximum power: 1600 W.

Screen plates with big and medium openings are ideal

for processing of raw meat, vegetables, nuts and dry

Manufacturer has the right to modify the specifications

fruit, cheese, fish etc.

without prior notice.

Screen plates with small openings are ideal for pro-

cessing of both raw and cooked meat, fish etc.

Service life of the appliance not less than 5 years

VEGETABLE CUTTER (22, 23, 24)

GUARANTEE

The appliance is completed with three attachments:

Details regarding guarantee conditions can be

two graters(23, 24) and shredder (22).

obtained from the dealer from whom the appliance was

purchased. The bill of sale or receipt must be produced

HOW TO TAKE CARE OF YOUR MEAT MINCER

when making any claim under the terms of this guaran-

 Always switch off and unplug the appliance after

tee.

use, make sure that the motor has stopped com-

pletely before disassembling the appliance.

This product conforms to the EMC-

 Turn off the nut (15), use the key (9), if necessary,

Requirements as laid down by the

and remove the screen plate and blade (13) from

Council Directive 89/336/EEC and to

the feeder screw. Remove the feeder screw (12)

the Law Voltage Regulation (73/23 EEC)

from the mincer head (3).

Press the mincer button (4), turn the head anti-

clockwise and withdraw.

 Remove the food residues, if any, from the feeder

screw.

9