Karcher Balayeuse KM 90-60 R Bp Pack Adv: F 1 F 2

     - 

10



Park the sweeper on an even surface.



Set programme switch to step 1 (driv-

ing). Roller brush is raised.



Turn main key to "0" and remove it.



Press emergency-stop button.



Secure the machine with wheel 

chock(s) to prevent it from rolling away.



Raise slightly the waste containers on 

both sides and pull them out.



Open the fastening screws of the side 

panels on both sides.



Remove side panels.



Front sealing strip



Loosen retaining nuts for the front seal-

ing strip (1) slightly (to replace, un-

screw).



Screw on new sealing strip without fully 

tightening the nuts.



Adjust sealing strip.



Set the distance between the sealing 

strip and the floor so that the bottom 

edge trails behind at a distance of be-

tween 10-15 mm.



Tighten nuts.



Rubber strip



If worn, replace.



Unscrew retaining nuts for the rubber 

strip (2).



Screw on new rubber strip.



Rear sealing strip



Set the distance between the sealing 

strip and the floor so that the bottom 

edge trails behind at a distance of be-

tween 5 and 10 mm.



If worn, replace.



Unscrew retaining nuts for rear sealing 

strip (3).



Screw on new sealing strip.



Side sealing strips



Slightly loosen retaining nuts for the 

side sealing strip (to replace, unscrew).



Screw on new sealing strip without fully 

tightening the nuts.



To set the floor clearance, insert a 

sheet with a thickness of between 1 and 

3 mm under the sealing strip.



Adjust sealing strip.



Tighten nuts.



Screw on side panels.



Push in the waste containers on both 

the sides and lock them.

몇

Warning

Wear a dust mask when working around 

the dust filter. Observe safety regulations 

on the handling of fine particles.

Note

: Wait at least 1 minute before remov-

ing the dust filter so that the dust can settle.



Open the device hood.

1 Screws (2x)

2 Lid with cleaning device

3 Support

4 Dust filter (flat-fold filter)



Loosen the screws.



Fold the lid up and secure it by means 

of the support.



Take out the dust filter.



Check dust filter, clean or replace



Insert cleaned or new dust filter. 



Close the lid. 



Tighten the screws. 



Check hose at the suction blower for 

tightness.



Turn main key to "0" and remove it.



Press emergency-stop button.



Open the device hood.



Check tension of circular belt of the 

side-brush; also check for wear or dam-

age.



Check tension, wear and damages on 

the V-belt of the sweep roller drive.



Check tension, wear and damages on 

the V-belt of the sweep roller drive.



Tighten the V-belt at the screw if neces-

sary.



Check tension, wear and damages on 

the V-belt of the sweep roller drive.



Replace defective fuse.



Pole fuse

Note

A defective pole fuse may only be replaced 

by a Kärcher service technician or an au-

thorised expert. If this fuse is defective, 

check the usage conditions and the entire 

control system.



Fuse rotating beacon (option)

To replace a fuse, the front panel must be 

removed.



Loosen the front panel screws.



Remove front panel.



Replace defective fuse.

Adjusting and replacing sealing strips

Check/replace dust filter

Check suction blower

Checking drive belt

Replacing the fuse

F 1 Main fuse

Battery pole fuse

150 A

F 2 Automotive flat plug fuse

Vacuum pump

3 A

F 5 Automotive flat plug fuse

Beacon light (optional)

Note

: This fuse is located 

underneath the front panel 

on the left hand side

7,5 A

F 1 F 2

24 EN