AEG MFE1500 4935413605: 20 21 ENGLISH
20 21 ENGLISH: AEG MFE1500 4935413605
Protect cutting discs against shock, impact and harmful
If needed, an exploded view of the tool can be ordered.
environmental factors.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
MAINS CONNECTION
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
SYMBOLS
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
CAUTION! WARNING! DANGER!
SPECIFIED CONDITIONS OF USE
The wall-chaser machine cuts slots for cables and pipes
(masonry grooves) in any kind of brickwork with two
diamond cutting discs running parallel to each other.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Do not use this product in any other way as stated for
normal use.
Appliances used at many different locations including wet
Please read the instructions carefully before
room and open air must be connected via a residual current
starting the machine.
device (FI, RCD, PRCD) of 30mA or less.
EC-DECLARATION OF CONFORMITY
Always wear goggles when using the
We declare under our sole responsibility that the product
machine.
described under “Technical Data” fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs),
2006/42/EC, 2004/108/EC and the following harmonized
standards have been used:
Wear ear protectors!
EN 60745-1:2009 + A11:2010
EN 60745-2-22:2011 + A11:2013
EN 55014-1:2006 + A 1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
Use an FFP2 particulate respirator as the
EN 61000-3-2:2006 + A1:2009 + A2:2009
minimum amount of protection.
EN 61000-3-3:2008
EN 50581:2012
Wear gloves!
Winnenden, 2014-08-11
Accessory - Not included in standard
Alexander Krug
equipment, available as an accessory.
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Do not dispose of electric tools together with
Max-Eyth-Straße 10
household waste material.
71364 Winnenden
Electric tools and electronic equipment that
Germany
have reached the end of their life must be
collected separately and returned to an
ADVICE FOR OPERATION
environmentally compatible recycling facility.
The speed of rotation is adjusted electronically when the
Check with your local authority or retailer for
load increases.
recycling advice and collection point.
In case of a longer overload period the speed is decreased
Class II tool, tool in which protection against
electronically. The machine continues to run slowly to cool
electric shock does not rely on basic
down the motor coil. After switching off and on the machine
insulation only, but in which additional safety
can be used at rated load.
precautions, such as double insulation or
Under the effect of extreme electromagnetic interferences
reinforced insulation, are provided.
from the outside, temporary variations in the speed of
There being no provision for protective
rotation could arise in particular cases.
earthing or reliance upon installation
conditions.
Sharpen blunt diamond cutting blades (can be recognised
by sparks fl ying while cutting) by making several cuts into
European Conformity Mark
calcareous sandstone or a special sharpening stone.
The cutting discs get very hot when in use. Do not touch
them before they have cooled down.
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
EurAsian Conformity Mark.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
20 21
ENGLISH
Оглавление
- 2 3
- 4 5
- 6 7
- 8 9
- 10 11
- 12 13
- 14 15
- 16 17
- 18 19ENGLISH ENGLISH
- 20 21 ENGLISH
- 22 23 DEUTSCH DEUTSCH
- 24 25 DEUTSCH DEUTSCH
- 26 27 FRANÇAIS FRANÇAIS
- 28 29 FRANÇAIS FRANÇAIS
- 30 31 ITALIANO ITALIANO
- 32 33 ITALIANO ITALIANO
- 34 35 ESPAÑOL ESPAÑOL
- 36 37 ESPAÑOL ESPAÑOL
- 38 39 PORTUGUES PORTUGUES
- 40 41 PORTUGUES PORTUGUES
- 42 43 NEDERLANDS NEDERLANDS
- 44 45 NEDERLANDS NEDERLANDS
- 46 47 DANSK DANSK
- 48 49 DANSK DANSK
- 50 51 NORSK NORSK
- 52 53 NORSK NORSK
- 54 55 SVENSKA SVENSKA
- 56 57 SVENSKA SVENSKA
- 58 59 SUOMI SUOMI
- 60 61 SUOMI SUOMI
- 62 63 ΕΛΛΗΝΙΚΑΕΛΛΗΝΙΚΑ
- 64 65 ΕΛΛΗΝΙΚΑΕΛΛΗΝΙΚΑ
- 66 67 TÜRKÇE TÜRKÇE
- 68 69 TÜRKÇE TÜRKÇE
- 70 71 ČESKY ČESKY
- 72 73 ČESKY ČESKY
- 74 75
- 76 77
- 78 79 POLSKI POLSKI
- 80 81 POLSKI POLSKI
- 82 83 MAGYAR MAGYAR
- 84 85 MAGYAR MAGYAR
- 86 87 SLOVENSKO SLOVENSKO
- 88 89 SLOVENSKO SLOVENSKO
- 90 91 HRVATSKIHRVATSKI HRVATSKI
- 92 93 HRVATSKI HRVATSKI
- 94 95 LATVISKI LATVISKI
- 96 97 LATVISKI LATVISKI
- 98 99
- 100 101
- 102 103 EESTI EESTI
- 104 105 EESTI EESTI
- 106 107 РУССКИЙРУССКИЙ
- 108 109 РУССКИЙРУССКИЙ
- 110 111 БЪЛГАРСКИ БЪЛГАРСКИ
- 112 113 БЪЛГАРСКИ БЪЛГАРСКИ
- 114 115 ROMÂNIA ROMÂNIA
- 116 117 ROMÂNIA ROMÂNIA
- 118 119 МАКЕДОНСКИ МАКЕДОНСКИ
- 120 121 МАКЕДОНСКИ МАКЕДОНСКИ
- 122 123 中文 中文
- 124 125
- 126 127 한국어 한국어