Vitek VT-1260: ENGLISH

ENGLISH

• Set the temperature control (7) to the re-

• Insert the power plug into the socket.

quired ironing temperature: “•”, “••”, “•••”

• Set the temperature control (7) to the required

or “MAX”, depending on the type of fabric,

ironing temperature: to steam using zone

the indicator in the temperature control (7) will

“•••” or “MAX”, the indicator in the tempera-

light up.

ture control (7) will light up.

• When the soleplate temperature (5) reaches

• When the soleplate temperature (5) reaches

the desired temperature value, the indicator

the desired temperature value, the indicator

will go out.

will go out, you can start ironing.

• Turn the constant steam supply regulator (3)

Note: While steam ironing set the tempera-

to set the intensity of steaming, steam will

ture to steam using zone, “•••” or “MAX”,

start outgoing from the openings of the sole-

plate (5). (pic.5.2.)

WATER SPRAYER

• After you finish ironing set the (7) temperature

• You can dampen the fabric by pressing the

control to the “MIN” position and the constant

spray button (2) several times (pic. 4).

steam supply control (3) to the “ ” position

• Make sure that there is enough water in the

(steam supply is off).

water tank.

• Pull the plug out of the socket and let the iron

cool down completely.

DRY IRONING

• Open the filling opening lid (9), turn over the

• Place the iron on the base (8).

unit and drain the remaining water (10). Close

• Set the constant steam supply control (3)

the lid (9) (pic.9).

to the “

” position (steam supply is off).

(pic.5.1)

ATTENTION!

• Set the temperature control (7) to the re-

If during the operation steam is not constantly

quired ironing temperature: “•”, “••”, “•••”

supplied, check whether the temperature con-

or “MAX”, depending on the type of fabric,

trol (7) is set properly and whether there is water

the indicator in the temperature control (7) will

in the water tank.

light up.

• When the soleplate temperature (5) reaches

ADDITIONAL steam supply

the desired temperature value, the indicator

Additional steam supply function is useful when

will go out, you can start ironing.

ironing folds and can only be used at high ironing

• After you finish ironing set the temperature

temperatures (when the iron temperature control

control (7) to the “MIN” position.

(7) is set to “•••” or “MAX”).

• Pull the plug out of the socket and let the iron

When the additional steam supply button (1) is

cool down completely.

pressed, steam will be vigorously released from

the openings in the iron soleplate (pic.6).

STEAM IRONING (pic.5)

For steam ironing set the temperature control to

Note:

steam using zone “•••” or “MAX”.

In order to avoid leakage of water from steam

The iron has an anti-drip valve, which stops wa-

openings, press the additional steam supply

ter supply, when the sole temperature is too low

button (1) with a 4-5 sec. interval.

it prevents the appearance of drops out of the

soleplate openings (5). While heating or cooling

VERTICAL STEAMING

down of the sole (5), you will hear clicks of open-

For vertical steaming can be used only when the

ing/closing of the anti-drip valve; it means that

high temperature mode is used (set the temper-

the valve works normally.

ature control (7) to the “•••” or “MAX” position.

• Make sure that there is enough water in the

Hold the iron vertically at the distance 15-30 cm

water tank.

from the clothes press the additional steam sup-

• Place the iron on the base (8).

ply button (1) with a 4-5 seconds interval, steam

• Set the constant steam supply control (3)

will be released from the openings in the iron

to the “ ” position (steam supply is off).

soleplate (5) (pic. 7).

(pic.5.1)

6

1260.indd 61260.indd 6 24.08.2010 10:02:3124.08.2010 10:02:31