Vitek VT-1260: ENGLISH
ENGLISH: Vitek VT-1260
ENGLISH
Note:
time, depending on the position of the tem-
• Do not fill it with water above the MAX.
perature control (7).
mark.
• If you need to refill the water tank during
IRONING TEMPERATURE
ironing, turn off the iron and unplug the
• Always check the recommended iron temper-
power cord from the outlet.
ature indicated on the tag before ironing.
• After you finish ironing, switch off the iron,
• If the tag does not list the recommended iron-
wait until it cools down completely, open
ing temperature, but you know the type of fab-
the filling opening lid (9) hold the unit in its
ric, then use the following table to determine
upright position and drain the remaining
the proper temperature.
water.
Signs Fabric type (temperature)
BEFORE FIRST USAGE
Synthetics, nylon, acryl, polyester
• Unpack the iron; remove the protection (if any)
•
(low temperature)
from the iron soleplate (5).
•• Silk/wool (medium temperature)
• Make sure that the electrical supply voltage
corresponds to the iron’s operating voltage.
••• Cotton/flax (high temperature)
• Fill the water tank with water (10).
• Insert the plug into the socket.
• This table is only for smooth materials. Fabrics
• Set the temperature control (7) to the “МАХ”
of other types (crimped, raised etc.) are best
position, the indicator in the temperature con-
ironed at low temperature.
trol (7) will light up.
• Firstly sort items by ironing temperature: wool
• When the soleplate temperature (5) reaches
with wool, cotton with cotton etc.
the desired temperature value, the indicator
• The iron heats up faster than is cools down.
will go out.
For this reason it is recommended to begin
• Set the steam supply control (3) to the “
”
ironing at low temperature (for instance syn-
position (steam supply is on), steam will start
thetic fabrics).
going out of the openings on the iron soleplate
• After that, move to higher temperature iron-
(5).
ing (silk/wool). Cotton and linens should be
• Before operating test the heated iron on the
ironed last.
old cloth to be sure that the iron soleplate (5)
• If an item is made from a mix of fabrics, then
and the water tank (10) are clean.
the iron should be set for the fabric with the
• The unit is ready to operate.
lowest ironing (for instance if an item is made
from 60% polyester and 40% cotton, it should
Note:
be ironed at the temperature used for ironing
When using the unit for the first time, the
polyester “•”).
heating element of the unit burns that is why
• If you cannot define the fabric the item is
some smoke or foreign odor can appear. It
made from, find a place on it that is hidden
is normal.
while wearing and, on practice select the iron-
ing temperature (always start at the lowest
“AUTOMATIC OFF” FUNCTION
and gradually raise it until you get the desired
If the iron is motionless during 30 seconds in
result.)
horizontal position or about 8 minutes in verti-
• Corduroy and other fabrics that start glossy
cal position, it will switch off automatically. The
quickly should be ironed strictly in one direc-
indicator in the temperature control (7) will be
tion (along the lines) with slight pressure.
flashing.
• To avoid appearance of glossy spots on the
To switch on the unit, just start ironing, the iron
synthetic and silk fabrics, iron them back-
will switch on and the indicator will stop flashing.
side.
Note:
SETTING THE IRONING TEMPERATURE
After the iron is switched on, the previously
• Place the iron on the base (8).
set soleplate temperature will be set in some
• Insert the power plug into the socket.
5
1260.indd 51260.indd 5 24.08.2010 10:02:3124.08.2010 10:02:31
Оглавление
- ENGLISH
- ENGLISH
- ENGLISH
- ENGLISH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ROMÂNĂ
- ROMÂNĂ
- ROMÂNĂ
- ROMÂNĂ
- ROMÂNĂ
- ČESKÝ
- ČESKÝ
- ČESKÝ
- ČESKÝ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК