Vitek VT-1259: ENGLISH
ENGLISH: Vitek VT-1259
ENGLISH
BEFORE USAGE
Signs Fabric type (temperature)
• Unpack the iron; remove the protection (if
Synthetics, nylon, acryl, polyester
•
any) from the iron sole (8).
(low temperature)
• Make sure that the electrical supply volt-
•• Silk/wool (medium temperature)
age corresponds to the iron’s operating
max (•••) Cotton/flax (high temperature)
voltage.
• This table is only for smooth materials.
Note:
Fabrics of other types (crimped, raised
- When using the unit for the first time,
etc.) are best ironed at low temperature.
the heating element of the unit burns
• Firstly sort items by ironing temperature:
that is why some smoke or foreign odor
wool with wool, cotton with cotton etc
can appear. It is normal.
• The iron heats up faster than is cools down.
For this reason it is recommended to be-
FILLING THE WATER TANK (pic. 1, 2)
gin ironing at low temperature (for instance
Make sure that the iron is disconnected from
synthetic fabrics).
electrical power before filling it with water.
• After that, move to higher temperature iron-
• Set the constant steam release regula-
ing (silk/wool). Cotton and linens should
tor (3) to the “0” position (steam supply is
be ironed last.
off).
• If an item is made from a mix of fabrics,
• Open the water tank lid (2).
then the iron should be set for the fabric
• Fill the unit with water using the water bowl
with the lowest ironing (for instance if an
(15); firmly close the lid (2).
item is made from 60% polyester and 40%
cotton, it should be ironed at the tempera-
Note:
ture used for ironing polyester “•”).
- Do not fill the unit with water above the
• If you cannot define the fabric the item is
“max” mark.
made from, find a place on it that is hid-
- If you need to refill water during iron-
den while wearing and, on practice select
ing, turn off the iron and unplug the
the ironing temperature (always start at the
power cord from the socket.
lowest and gradually raise it until you get
- After you finish ironing, switch off the
the desired result.)
unit, wait till it cools down completely,
• Corduroy and other fabrics that start glossy
open the water tank lid (2), turn over
quickly should be ironed strictly in one di-
the iron and pour out the remaining wa-
rection (along the lines) with slight pres-
ter.
sure.
• To avoid appearance of glossy spots on the
IRONING TEMPERATURE
synthetic and silk fabrics, iron them back-
Before operating test the heated iron on the
side.
old cloth to be sure that the iron sole (8) and
the water tank (11) are clean.
SETTING THE IRONING TEMPERATURE
• Always check the recommended iron tem-
• Place the iron on the base (14).
perature indicated on the tag before iron-
• Insert the power plug into the socket.
ing.
• Set the temperature regulator (12) to the
• If the tag does not list the recommended
required ironing temperature: “•”, “••”,
ironing temperature, but you know the type
“•••” or “max” (•••) (pic.3), depending
of fabric, then use the following table to
on the type of fabric, the (13) indicator will
determine the proper temperature.
light up.
• When the sole temperature (12) reaches
the desired temperature value, the (13) in-
dicator will go out, you can start ironing.
5
1259.indd 51259.indd 5 16.07.2010 17:15:3816.07.2010 17:15:38
Оглавление
- ENGLISH
- ENGLISH
- ENGLISH
- ENGLISH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ROMÂNĂ
- ROMÂNĂ
- ROMÂNĂ
- ROMÂNĂ
- ROMÂNĂ
- ČESKÝ
- ČESKÝ
- ČESKÝ
- ČESKÝ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК