Pioneer S-21W: Troubleshooting
Troubleshooting: Pioneer S-21W
01_S-21W&S-11.book 13 ページ 2010年3月16日 火曜日 午前11時28分
Troubleshooting
English Français Deutsch
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie
in another component. Investigate the other components and electrical appliances being used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest
PIONEER authorized service center or your dealer to carry out repair work.
S-21W
Symptom Cause Remedy
No power is being supplied
• Power supply plug is not
• Insert plug securely.
(Indicator does not light up
correctly inserted.
when POWER switch is
turned on) .
No sound
• Connection of accessory
• Check again and connect
(Indicator is lit blue) .
RCA plug cord is wrong or
correctly.
disconnected.
Italiano Español
• Volume knob is set to MIN.
• Turn clockwise slowly.
• Input level is too low.
• Raise the receiver’s output
level.
Sound is distorted. • Level is too high.
• Turn the volume knob
counter-clockwise to lower
Nederlands
the level.
• Input level is too high.
•Turn the
receiver’s output
level (volume, bass control,
bass boost) counter-
clockwise to lower the level.
Howling noise occurs. • No power supplied to the
• Connect an
receiver and
receiver.
supply power.
• Subwoofer level is set too
• Place the subwoofer a good
high.
distance from speakers.
Turn the volume knob
counter-clockwise to lower
the volume.
Pyccкий
Much noise when listening
• The AM loop antenna or
• Increase the distance
to AM or FM broadcasts.
the FM indoor antenna is
between the AM or FM
close to this unit.
antenna (for indoor use)
and this unit.
13
En
01_S-21W&S-11.book 14 ページ 2010年3月16日 火曜日 午前11時28分
Symptom Cause Remedy
No sound is produced
• Unit has entered standby
• Turn the Auto Standby
(power indicator lights red)
mode.
function OFF.
– When the Auto Standby
Initial sounds of a track
• The audio signal was input
function is turned ON, if
can’t be heard.
when the unit was in the
no signal (or only a very
standby mode.
weak signal) is input for
a period of about ten
minutes, the power
mode will automatically
change to standby.
– Note that when listening
with the volume set to a
very low level, the Auto
Standby function may
operate, switching the
unit to the standby
mode.
S-11
Symptom Cause Remedy
No sound. • Incorrect connection of
• Connect correctly.
speaker wire.
•Turn on receiver.
• Receiver is off.
• Slowly turn up volume.
• Volume control is at zero.
Sound is distorted. • Extreme signal condition. • Turn down the receiver’s
output level (volume, bass
control, bass boost) to
lower the level.
Speakers stop producing
• An excessively large signal
• Turn the volume down to
sound suddenly.
was input, resulting in the
resume normal speaker
operation of the automatic
output.
protection circuit.
Published by Pioneer Corporation.
Copyright © 2010 Pioneer Corporation.
All rights reserved.
14
En
01_S-21W&S-11.book 15 ページ 2010年3月16日 火曜日 午前11時28分
English Français Deutsch
Italiano Español
Nederlands
Pyccкий
15
En
Оглавление
- IMPORTANT
- Contents Installation
- Connections and Use
- Connections and Use
- Specifications
- Troubleshooting
- IMPORTANT
- Sommaire Installation
- Branchements et
- Branchements et
- Fiche technique
- Guide de dépannage
- WICHTIG
- Inhaltsverzeichnis Aufstellung
- Anschlüsse und
- Anschlüsse und
- Technische Daten
- Störungsbeseitigung
- IMPORTANTE
- Indice Installazione
- Collegamenti ed uso
- Collegamenti ed uso
- Dati tecnici
- Diagnostica
- BELANGRIJK
- Inhoudsopgave Installatie
- Aansluitingen en
- Aansluitingen en
- Technische gegevens
- Oplossen van problemen
- IMPORTANTE
- Índice Instalación
- Conexiones y
- Conexiones y
- Especificaciones
- Solución de problemas
- BAЖHO
- Содержание Установка
- Подключение и
- Подключение и
- Технические характеристики
- Поиск и устранение неполадок
- 目錄 安裝
- 連接及使用 (S-21W)
- 連接及使用 (S-11)
- 規格
- 故障排除