Pioneer DEH-2300UB: инструкция

Thank you for purchasing this PIONEER

product.

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible

place for future reference.

Section

01

Before You Start

Middle East, Africa and Oceania. Use in other

areas may result in poor reception. The RDS

(radio data system) function only operates in

areas with broadcasting RDS signals for FM

stations.

CAUTION

This product is a class 1 laser product classi-

fied under the Safety of laser products, IEC

60825-1:2007, and contains a class 1M laser

module. To ensure continued safety, do not re-

move any covers or attempt to gain access to

the inside of the product. Refer all servicing to

qualified personnel.

If you want to dispose this product, do not mix

it with general household waste. There is a se-

parate collection system for used electronic

products in accordance with legislation that re-

quires proper treatment, recovery and recy-

CAUTION—CLASS 1M INVISIBLE LASER

cling.

RADIATION WHEN OPEN, DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

Private households in the member states of

the EU, in Switzerland and Norway may return

their used electronic products free of charge

to designated collection facilities or to a retai-

CAUTION

ler (if you purchase a similar new one).

! Do not allow this unit to come into contact

For countries not mentioned above, please

with liquids. Electrical shock could result.

contact your local authorities for the correct

Also, damage to this unit, smoke, and over-

method of disposal.

heating could result from contact with liquids.

By doing so you will ensure that your disposed

! The Pioneer CarStereo-Pass is for use only in

product undergoes the necessary treatment,

Germany.

recovery and recycling and thus prevent po-

! Always keep the volume low enough to hear

tential negative effects on the environment

outside sounds.

and human health.

! Avoid exposure to moisture.

! If the battery is disconnected or discharged,

any preset memory will be erased.

In case of trouble

Note

Should this unit fail to operate properly, please

Function setting operations are completed even if

contact your dealer or nearest authorized

the menu is cancelled before the operations are

PIONEER Service Station.

confirmed.

About this unit

The tuner frequencies on this unit are allo-

cated for use in Western Europe, Asia, the

2

En

Demo mode

Section

Before You Start

01

English

Important

! Failure to connect the red lead (ACC) of this

unit to a terminal coupled with ignition switch

on/off operations may lead to batter y drain.

! Remember that if the feature demo continues

operating when the car engine is turned off, it

may drain battery power.

The demo automatically starts when the igni-

tion switch is set to ACC or ON while the unit

is turned off. Turning off the unit does not can-

cel demo mode. To cancel the demo mode, op-

erate the function in the initial setting menu.

Operating the demo while the ignition switch

is set to ACC may drain battery power.

En

3

Head unit

1

24 5 63

Part Part

(Back/display/

1 S (SRC/OFF) 8

scroll)

2 h (eject) 9 a/b/c/d

3

(list) a TA/NEWS

MULTI-CONTROL

4

b 1 to 6

(M.C.)

AUX input jack (3.5

5 Disc loading slot c

mm stereo jack)

6 USB port d Detach button

7 B (BAND/ESC)

CAUTION

! Use an optional Pioneer USB cable (CD-U50E)

to connect the USB audio player/USB mem-

ory as any device connected directly to the

unit will protrude out from the unit and may

be dangerous.

! Do not use unauthorized products.

Display indication

63

8 a

c

Section

02

Operating this unit

Indicator State

! Tuner: band and frequency

! RDS: program service name,

Main dis-

PTY information and other lit-

1

play sec-

eral information

tion

! Built-in CD player and USB:

elapsed playback time and

text information

An upper tier of folder or menu

2 c

exists.

A lower tier of folder or menu ex-

3 d

ists.

4

(list) The list function is operated.

The disc (track) artist name is dis-

5

(artist)

played.

The disc (album) name is dis-

6

(disc)

played.

The track (song) name is dis-

played.

7

(song)

A playable audio file has been se-

lected while operating the list.

8 LOC Local seek tuning is on.

9

(TA) TA function is on.

a

(TP) A TP station is tuned in.

b

(repeat) Track or folder repeat is on.

(ran-

c

Random play is on.

dom)

The sound retriever function is

d

(sound re-

on.

triever)

1

Basic Operations

Important

! Handle gently when removing or attaching

the front panel.

2

9

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight and

high temperatures.

4

En

! To avoid damaging the device or vehicle inter-

ior, remove any cables and devices attached

to the front panel before detaching it.

Removing the front panel to protect your unit from

theft

1 Press the detach button to release the front

panel.

2 Push the front panel upward and pull it toward

you.

Section

Operating this unit

02

English

CAUTION

For safety reasons, park your vehicle when remov-

ing the front panel.

Note

When this unit’s blue/white lead is connected to

the vehicle’s auto-antenna relay control terminal,

the vehicle’s antenna extends when this unit’s

source is turned on. To retract the antenna, turn

the source off.

Menu operations identical

for function settings/audio

3 Always keep the detached front panel in a protec-

adjustments/initial

tion device such as a protection case.

settings/lists

Re-attaching the front panel

1 Slide the front panel to the left.

Make sure to insert the tabs on the left side of the

Returning to the previous display

head unit into the slots on the front panel.

Returning to the previous list (the folder one level

higher)

1 Press

.

Returning to the main menu

Returning to the top tier of list

1 Press and hold

.

Returning to the ordinary display

Canceling the initial setting menu

1 Press B (BAND/ESC).

2 Press the right side of the front panel until it is

firmly seated.

Returning to the ordinary display from the list

If you cannot attach the front panel to the head

1 Press B (BAND/ESC).

unit successfully, make sure that you are placing

the front panel onto the head unit correctly. For-

cing the front panel into place may result in da-

mage to the front panel or head unit.

Turning the unit on

1 Press S (SRC/OFF) to turn the unit on.

Turning the unit off

1 Press and hold S (SRC/OFF) until the unit turns

off.

Selecting a source

1 Press S (SRC/OFF) to cycle between:

TUNER (tuner)—CD (built-in CD player)—USB

(USB)—AUX (AUX)

Adjusting the volume

1 Turn M.C. to adjust the volume.

En

5

Tuner

Basic Operations

Selecting a band

1 Press B (BAND/ESC) until the desired band (F1,

F2, F3 for FM or MW/LW) is displayed.

Manual tuning (step by step)

1 Press c or d.

Seeking

1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing c

or d.

While pressing and holding c or d, you can skip

stations. Seek tuning starts as soon as you re-

lease c or d.

Note

This unit’s AF (alternative frequencies search)

function can be turned on and off. AF should be

off for normal tuning operation (refer to page 10).

Storing and recalling stations

for each band

Using preset tuning buttons

1 When you find a station that you want

to store in memory, press one of the preset

tuning buttons (1 to 6) and hold until the

preset number stops flashing.

2 Press one of the preset tuning buttons

(1 to 6) to select the desired station.

# You can also recall stored radio stations by

pressing a or b during the frequency display.

Switching the RDS display

RDS (radio data system) contains digital infor-

mation that helps search for the radio sta-

tions.

% Press

Section

02

Operating this unit

PTY list

NEWS/INFO

NEWS (News), AFFAIRS (Current affairs), INFO (Infor-

mation), SPORT (Sports), WEATHER (Weather), FI-

NANCE (Finance)

POPULAR

POP MUS (Popular music), ROCK MUS (Rock

music), EASY MUS (Easy listening), OTH MUS

(Other music), JAZZ (Jazz), COUNTRY (Country

music), NAT MU S (National music), OLDIES (Oldies

music), FOLK MUS (Folk music)

CLASSICS

L. CLASS (Light classical), CLASSIC (Classical)

OTHERS

EDUCATE (Education), DRAMA (Drama), CULTURE

(Culture), SCIENCE (Science), VARIED (Varied), CHIL-

DREN (Children’s), SOCIAL (Social affairs), RELIGION

(Religion), PHONE IN (Phone in), TOURING (Travel),

LEISURE (Leisure), DOCUMENT (Documentaries)

.

Program service name—PTY information—

Frequency

# PTY information and the frequency appear on

the display for eight seconds.

6

En

Advanced operations using

REGION (regional)

special buttons

When AF is used, the regional function limits the se-

lection of stations to those broadcasting regional pro-

Receiving traffic announcements

grams.

Regardless of the source you are listening to, you can

1 Press M.C. to turn the regional function on or off.

receive traffic announcements automatically with TA

(traffic announcement standby).

LOCAL (local seek tuning)

1 Tune in to a TP or en hanced other network’sTP

Local seek tuning lets you tune in to only those radio

station.

stations with sufficiently strong signals for good re-

2 Press TA/NEWS to turn traffic announcement

ception.

standby on or off.

1 Press M.C. to display the setting mode.

3 Use M.C. to adjust the TA volume when a traffic

2 Turn M.C. to select the desired setting.

announcement begins.

FM: OFF—LEVEL 1—LEVEL 2—LEVEL 3—LEVEL

The newly set volume is stored in the memory

4

and will be recalled for subsequent traffic an-

MW/LW: OFF—LEVEL 1—LEVEL 2

nouncements.

The highest level setting allows reception of only

4 Press TA/NEWS while a traffic announcement is

the strongest stations, while lower levels allow the

being received to cancel the announcement.

reception of weaker stations.

The tuner returns to the original source but re-

3 Press M.C. to confirm the selection.

mains in the standby mode until TA/NEWS is

pressed again.

PTY SEARCH (program type selection)

Using news program interruption

You can tune in to a station using PTY (program type)

When a news program is broadcast from a PTY code

information.

news station, the unit automatically switches to the

1 Press M.C. to display the setting mode.

news broadcast station. When the news program

2 Turn M.C. to select the desired setting.

ends, reception of the previous program resumes.

NEWS/INFO—POPULAR—CLASSICS—OTHERS

1 Press and hold TA/NEWS to turn news program

3 Press M.C. to begin the search.

interruption on or off.

The unit searches for a station broadcasting that

A news program can be canceled by pressing TA/

type of program. When a station is found, its pro-

NEWS.

gram service name is displayed.

PTY (program type ID code) information is listed

in the following section. Refer to the previous

page.

Function settings

The program of some stations may differ from

1 Press M.C. to display the main menu.

that indicated by the transmitted PTY.

If no station is broadcasting the type of program

2 Turn M.C. to change the menu option

you searched for, NOT FOUND is displayed for

and press to select FUNCTION.

about two seconds and then the tuner returns to

the original station.

3 Turn M.C. to select the function.

TA (traffic announcement standby)

After selecting, perform the following proce-

dures to set the function.

1 Press M.C. to turn traffic announcement standby

# If MW/LW band is selected, only BSM or

on or off.

LOCAL is available.

AF (alternative frequencies search)

BSM (best stations memory)

1 Press M.C. to turn AF on or off.

BSM (best stations memory) automatically stores the

NEWS (news program interruption)

six strongest stations in the order of their signal

strength.

1 Press M.C. to turn the NEWS function on or off.

1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

Section

Operating this unit

02

English

En

7

CD/CD-R/CD-RW and USB

storage devices

Basic Operations

Playing a CD/CD-R/CD-RW

1 Insert the disc into the disc loading slot with the

label side up.

Ejecting a CD/CD-R/CD-RW

1 Press h.

Playing songs on a USB storage device

1 Open the USB connector cover and plug in the

USB storage device using a USB cable.

Stopping playback of files on a USB storage device

1 You may disconnect the USB storage device at

anytime.

Selecting a folder

1 Press a or b.

Selecting a track

1 Press c or d.

Fast forwarding or reversing

1 Press and hold c or d.

! When playing compressed audio, there is no

sound during fast forward or reverse.

Returning to root folder

1 Press and hold B (BAND/ESC).

Switching between compressed audio and CD-DA

1 Press B (BAND/ESC).

Note

Disconnect USB storage devices from the unit

when not in use.

Displaying text information

Selecting the desired text information

1 Press

Section

02

Operating this unit

Selecting and playing files/

tracks from the name list

1 Press to switch to the file/track

name list mode.

2 Use M.C. to select the desired file name

(or folder name).

Changing the file or folder name

1 Turn M.C.

Playing

1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the selected

folder

1 When a folder is selected, press M.C.

Playing a song in the selected folder

1 When a folder is selected, press and hold M.C.

Advanced operations using

special buttons

Selecting a repeat play range

1 Press 6/

to cycle between the following:

CD/CD-R/CD-RW

! DISC – Repeat all tracks

! TRACK – Repeat the current track

! FOLDER – Repeat the current folder

USB audio player/USB memory

! ALL – Repeat all files

! TRACK – Repeat the current file

! FOLDER – Repeat the current folder

Playing tracks in random order

1 Press 5/

to turn random play on or off.

Tracks in a selected repeat range are played in

random order.

Pausing playback

.

1 Press 2/ PAUSE to pause or resume.

Scrolling the text information to the left

Enhancing compressed audio and restoring rich

sound (sound retriever)

1 Press and hold

.

1 Press 1/ S.Rtrv to cycle between:

Notes

OFF (off)—1—2

1 is effective for low compression rates, and 2 is

! Depending on the version of iTunes used to

effective for high compression rates.

write MP3 files to a disc or media file types, in-

compatible text stored within an audio file

may be displayed incorrectly.

Function settings

! Text information items that can be changed

depend on the media.

1 Press M.C. to display the main menu.

8

En

2 Turn M.C. to change the menu option

FAD/BAL (fader/balance adjustment)

and press to select FUNCTION.

1 Press M.C. to display the setting mode.

3 Turn M.C. to select the function.

2 Press M.C. to cycle between fader (front/rear) and

After selecting, perform the following proce-

balance (lef t/right).

dures to set the function.

3 Turn M.C. to adjust speaker ba lance.

! When the rear output and RCA output setting are

REPEAT (repeat play)

SW, you cannot adjust front/rear speaker balance.

Refer to SW CONTROL (rear output and subwoofer

1 Press M.C. to display the setting mode.

setting) on page 11.

2 Turn M.C. to select a repeat play range.

EQUALIZER (equalizer recall)

For details, refer to Selecting a repeat play range on

the previous page.

1 Press M.C. to display the setting mode.

3 Press M.C. to confirm the selection.

2 Turn M.C. to select the equalizer.

RANDOM (random play)

DYNAMIC—VOCAL—NATURAL—CUSTOM—

FLAT—POWERFUL

1 Press M.C. to turn random play on or off.

3 Press M.C. to confirm the selection.

PAUSE (pause)

TONE CTRL (equalizer adjustment)

1 Press M.C. to pause or resume.

! Adjusted equalizer curve settings are stored in

CUSTOM.

S.RTRV (sound retriever)

1 Press M.C. to display the setting mode.

Automatically enhances compressed audio and re-

2 Press M.C. to select BASS (bass)/MID (mid)/TRE-

stores rich sound.

BLE (treble).

1 Press M.C. to display the setting mode.

3 Turn M.C. to adjust the level.

2 Turn M.C. to select the desired setting.

Adjustment range: +6 to -6

For details, refer to Enhancing compressed audio

LOUDNESS (loudne ss)

and restoring rich sound (sound retriever) on the

previous page.

Loudness compensates for deficiencies in the low-

3 Press M.C. to confirm the selection.

and high-frequency ranges at low volume.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

OFF (off)—LOW(low)—HIGH (high)

3 Press M.C. to confirm the selection.

Audio Adjustments

SUBWOOFER1 (subwoofer on/off setting)

1 Press M.C. to display the main menu.

This unit is equipped with a subwoofer output which

can be turned on or off.

2 Turn M.C. to change the menu option

1 Press M.C. to display the setting mode.

and press to select AUDIO.

2 Turn M.C. to select the desired setting.

NORMAL (normal phase)—REVERSE (reverse

3 Turn M.C. to select the audio function.

phase)—OFF (subwoofer off)

After selecting, perform the following proce-

3 Press M.C. to confirm the selection.

dures to set the audio function.

SUBWOOFER2 (subwoofer adjustment)

Section

Operating this unit

02

English

En

9

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off frequency

and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.)—Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—100HZ

—125HZ

Output level: -24 to +6

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! Settings are based on the FM volume level, which

remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial Settings

Section

02

Operating this unit

# (DEH-2310UB)

Press M.C. and hold until function name ap-

pears in the display.

3 Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

Only for DEH-2310UB.

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock dis-

play you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

CLOCK (clock display)

Only for DEH-2310UB.

You can turn the clock display on or off.

The clock display disappears temporarily when you

per form other operations, but the clock display ap-

pears again after 25 seconds.

1 Press M.C. to turn the clock display on or off.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek tun-

ing is 50 kHz. When AF or TA is on, the tuning step

automatically changes to 100 kHz. It may be prefer-

able to set the tuning step to 50 kHz when AF is on.

! The tuning step remains at 50 kHz during manual

tuning.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the FM tuning step.

50 KHZ (50 kHz)—100 KHZ (100 kHz)

Important

3 Press M.C. to confirm the selection.

PW SAVE (power saving) is cancelled if the vehi-

AUTO-PI (auto PI seek)

cle batter y is disconnected and will need to be

The unit can automatically search for a different sta-

turned back on once the battery is reconnected.

tion with the same programming, even during preset

When PW SAVE (power saving) is off, depending

recall.

on connection methods, the unit may continue to

1 Press M.C. to turn Auto PI seek on or off.

draw power from the battery if your vehicle's igni-

AUX (auxiliary input)

tion switch doesn't have an ACC (accessory posi-

tion).

Activate this setting when using an auxiliary device

connected to this unit.

1 Press and hold S (SRC/OFF) until the

1 Press M.C. to turn AUX on or off.

unit turns off.

USB (plug and play)

2 Display the function name.

# (DEH-2300UB, DEH-2300UBB and DEH-

2320UB)

Press S (SRC/OFF) and hold until function

name appears in the display.

10

En

This setting allows you to switch your source to USB

This unit can display the text information of a com-

automatically.

pressed audio file even if they are embedded in a

1 Press M.C. to turn the plug and play functio n on

Western European or Russian language.

or off.

! If the embedded language and the selected lan-

ON – When USB storage device is connected, de-

guage setting are not the same, text information

pending on the type of device, the source is auto-

may not be displayed properly.

matically switched to USB when you turn on the

! Some characters may not be displayed properly.

engine. If you disconnect your USB storage de-

1 Press M.C. to display the setting mode.

vice, this unit’s source is turned off.

2 Turn M.C. to select the desired setting.

OFF – When USB storage device is connected,

EUROPEAN (European)—RUSSIAN (Russian)

the source is not switched to USB automatically.

3 Press M.C. to confirm the selection.

Please change the source to USB manually.

PW SAVE (power saving)

ILLUMI (illumination color select)

Only for DEH-2300UB, DEH-2300UBB and DEH-

Only for DEH-2310UB.

2320UB.

1 Press M.C. to display the setting mode.

Switching this function on enables you to reduce the

2 Turn M.C. to select the desired setting.

consumption of batter y power.

RED (red)—GREEN (green)

! Turning on the source is the only operation al-

3 Press M.C. to confirm the selection.

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

SW CONTROL (rear output and subwoofer setting)

The rear speaker leads output and RCA output can be

used for full-range speaker or subwoofer connection.

If you switch to REAR-SP:SW, you can connect a rear

speaker lead directly to a subwoofer without using an

Using an AUX source

auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker

1 Insert the stereo mini plug into the

connection (FUL).

AUX input jack.

1 Press M.C. to display the setting mode.

2 Turn M.C. to change the output and press to se-

2 Press S (SRC/OFF) to select AUX as the

lect.

source.

REAR-SP—PREOUT

3 Turn M.C. to change the setting.

Note

REAR-SP: FUL—SW

AUX cannot be selected unless the auxiliary set-

PREOUT: SW—REA

! Even if you change this setting, there is no

ting is turned on. For more details, refer to AUX

output unless you turn the subwoofer output

(auxiliary input) on the previous page.

on (refer to SUBWOOFER1 (subwoofer on/off

setting) on page 9).

! If you change this setting, subwoofer output

in the audio menu will return to the factory

Sound muting

settings.

Only for DEH-2300UB, DEH-2300UBB and

DEMO (demo display setting)

DEH-2320UB.

Sound is muted automatically when:

1 Press M.C. to turn the demo display on or off.

! A call is made or received using a cell

SCROLL (scroll mode setting)

phone connected to this unit.

! Voice guidance is output from a connected

When ever scroll is set to ON, recorded text informa-

Pioneer navigation unit.

tion scrolls continuously in the display. Set to OFF if

you prefer the information to scroll just once.

The sound is turned off, MUTE is displayed

1 Press M.C. to turn the ever scroll on or off.

and no audio adjustments, except volume con-

trol, are possible. Operation returns to normal

TITLE (multi-language)

when the phone connection or the voice gui-

dance is ended.

Section

Operating this unit

02

English

En

11

Connections

— Never band together negative cables of

multiple speakers.

Important

! When this unit is on, control signals are sent

! When installing this unit in a vehicle without

through the blue/white cable. Connect this

an ACC (accessory) position on the ignition

cable to the system remote control of an exter-

switch, failure to connect the red cable to the

nal power amp or the vehicle’s auto-antenna

terminal that detects operation of the ignition

relay control terminal (max. 300 mA 12 V DC).

key may result in battery drain.

If the vehicle is equipped with a glass anten-

na, connect it to the antenna booster power

F

F

O

N

O

supply terminal.

S

A

T

T

R

! Never connect the blue/white cable to the

power terminal of an external power amp.

ACC position No ACC position

Also, never connect it to the power terminal of

the auto antenna. Doing so may result in bat-

! Use of this unit in conditions other than the

tery drain or a malfunction.

following could result in fire or malfunction.

! The black cable is ground. Ground cables for

— Vehicles with a 12-volt battery and negative

this unit and other equipment (especially,

grounding.

high-current products such as power amps)

— Speakers with 50 W (output value) and 4

must be wired separately. If they are not, an

ohm to 8 ohm (impedance value).

accidental detachment may result in a fire or

! To prevent a short-circuit, overheating or mal-

malfunction.

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the

This unit

battery before installation.

— Secure the wiring with cable clamps or ad-

1

hesive tape. Wrap adhesive tape around

wiring that comes into contact with metal

parts to protect the wiring.

— Place all cables away from moving parts,

such as the gear shift and seat rails.

— Place all cables away from hot places,

such as near the heater outlet.

— Do not connect the yellow cable to the bat-

tery by passing it through the hole to the

engine compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable

of this unit in order to share the power

with other devices. The current capacity of

the cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable di-

rectly to ground.

Section

03

Installation

2

1 Power cord input

2 Rear output or subwoofer output

3 Antenna input

4 Fuse (10 A)

5 Wired remote input

Only for DEH-2300UB, DEH-2300UBB and

DEH-2320UB.

Hard-wired remote control adaptor can be

connected (sold separately).

12

En

Power cord

3

4

5

1

2

6

3

4

7

5

6

8

a

9

b

e

Section

Installation

03

English

b Blue/white

Connect to auto-antenna relay control term-

inal (max. 300 mA 12 V DC).

c Yellow/black

Only for DEH-2300UB, DEH-2300UBB and

DEH-2320UB.

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

d Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear lef t * or subwoofer *

c

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

e ISO connector

In some vehicles, the ISO connector may be

1 To power cord input

divided into two. In this case, be sure to con-

2 Depending on the kind of vehicle, the function

nect to both connectors.

of 3 and 5 may be different. In this case, be

sure to connect 4 to 5 and 6 to 3.

Notes

3 Yellow

! Change the initial setting of this unit. Refer to

Back-up (or accessory)

SW CONTROL (rear output and subwoofer set-

4 Yellow

ting) on page 11.

Connect to the constant 12 V supply terminal.

The subwoofer output of this unit is monaural.

5 Red

! When using a subwoofer of 70 W (2 Ω), be

Accessory (or back-up)

sure to connect the subwoofer to the violet

6 Red

and violet/black leads of this unit. Do not con-

Connect to terminal controlled by ignition

nect anything to the green and green/black

switch (12 V DC).

leads.

7 Connect leads of the same color to each

other.

8 Black (chassis ground)

Power amp (sold separately)

9 Blue/white

Perform these connections when using the

The pin position of the ISO connector will dif-

optional amplifier.

fer depending on the type of vehicle. Connect

1

3

9 and b when Pin 5 is an antenna control

2

type. In another type of vehicle, never connect





4

9 and b.

55

a Blue/white





Connect to system control terminal of the

1 System remote control

power amp (max. 300 mA 12 V DC).

Connect to Blue/white cable.

En

13

2 Power amp (sold separately)

3 Connect with RCA cable (sold separately)

4 To Rear output or subwoofer output

5 Rear speaker or subwoofer

Installation

Section

03

Installation

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°)

into place.

1

Important

! Check all connections and systems before

2

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

1 Dashboard

! Consult your dealer if installation requires dril-

2 Mounting sleeve

ling of holes or other modifications to the vehi-

3 Install the unit as illustrated.

cle.

! Do not install this unit where:

1

— it may interfere with operation of the vehi-

2

cle.

— it may cause injury to a passenger as a re-

sult of a sudden stop.

3

! The semiconductor laser will be damaged if it

4

overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

5

unit is installed at an angle of less than 60°.

1 Nut

60°

2 Firewall or metal support

3 Metal strap

4 Screw

5 Screw (M4 × 8)

# Make sure that the unit is installed securely in

DIN front/rear mount

place. An unstable installation may cause skip-

This unit can be properly installed using either

ping or other malfunctions.

front-mount or rear-mount installation.

Use commercially available parts when instal-

DIN Rear-mount

ling.

1 Determine the appropriate position

where the holes on the bracket and the

DIN Front-mount

side of the unit match.

1 Insert the mounting sleeve into the

dashboard.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough

space, use the mounting sleeve that came

with the vehicle.

14

En

2 Tighten two screws on each side.

1

3

2

1 Tapping screw (5 mm × 8 mm)

2 Mounting bracket

3 Dashboard or console

Removing the unit

1 Remove the trim ring.

Section

Installation

03

English

Press the detach button and push the front

panel upward and pull it toward you.

For details, refer to Removing the front panel to

protect your unit from theft and Re-attaching

the front panel on page 5.

1 Trim ring

2 Notched tab

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2 Insert the supplied extraction keys into

both sides of the unit until they click into

place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the

front panel

You can remove the front panel to protect your

unit from theft.

En

15

Troubleshooting

Symptom Cause Action

The display

You did not per-

Perform operation

automatically

form any opera-

again.

returns to the

tion within about

ordinary dis-

30 seconds.

play.

The repeat play

Depending on

Select the repeat

range changes

the repeat play

play range again.

unexpectedly.

range, the se-

lected range may

change when se-

lecting another

folder or track, or

when fast for-

warding/rever-

sing.

A subfolder is

Subfolders can-

Select another re-

not played

not be played

peat play range.