Pioneer GM-D9601: инструкция
Характеристики, спецификации
Инструкция к Усилителю автомобильному Pioneer GM-D9601
English Nederlands
CLASS D MONO AMPLIFIER
AMPLIFICATEUR MONO DE CLASSE D
AMPLIFICATORE MONOFONICO DI CLASSE D
Français Italiano Español Deutsch
AMPLIFICADOR MONO DE LA CLASE D
MONOVERSTÄRKER DER KLASSE D
MONOVERSTERKER KLASSE D
МОНОФОНИЧЕСКИЙ УСИЛИТЕЛЬ КЛАССА D
GM-D8601
GM-D9601
Owner’s Manual
Mode d’emploi
Manuale d’istruzioni
Manual de instrucciones
Bedienungsanleitung
Русский
Handleiding
Руководство пользователя
Section
01
Before you start
Thank you for purchasing this PIONEER
! We offer the latest information about
product
PIONEER CORPORATION on our
website.
To ensure proper use, please read through this
manual before using this product. It is espe-
If you experience problems
cially important that you read and observe
WARNINGs and CAUTIONs in this manual.
Should this product fail to operate properly,
Please keep the manual in a safe and accessible
please contact your dealer or nearest author-
place for future reference.
ized Pioneer Service Station.
About This Product
This product is a mono amplifier for subwoofer. If
both L (left) and R (right) channels are connected
to the RCA input of this product, output is mixed
because this product is a mono amplifier.
If you want to dispose this product, do not mix
it with general household waste. There is a se-
parate collection system for used electronic
Before connecting/
products in accordance with legislation that re-
quires proper treatment, recovery and recy-
installing the amplifier
cling.
WARNING
! This unit is for vehicles with a 12 V battery and
Private households in the member states of
negative grounding. Before installing in re-
the EU, in Switzerland and Norway may return
creational vehicles, trucks or buses, check the
their used electronic products free of charge
battery voltage.
to designated collection facilities or to a retai-
! When installing this unit, make sure to con-
ler (if you purchase a similar new one).
nect the ground wire first. Ensure that the
For countries not mentioned above, please
ground wire is properly connected to metal
contact your local authorities for the correct
parts of the car’s body. The ground wire of the
method of disposal.
one of this unit must be connected to the car
By doing so you will ensure that your disposed
separately with different screws. If the screw
product undergoes the necessary treatment,
for the ground wire loosens or falls out, it
recovery and recycling and thus prevent po-
could result in fire, generation of smoke or
tential negative effects on the environment
malfunction.
and human health.
! Be sure to install the fuse to the battery wire.
! Always use a fuse of the rating prescribed.
The use of an improper fuse could result in
Visit our website
overheating and smoke, damage to the pro-
Visit us at the following site:
duct and injury, including burns.
http://www.pioneer.co.uk
! Check the connections of the power supply
! Register your product. We will keep the de-
and speakers if the fuse of the separately sold
tails of your purchase on file to help you
battery wire or the amplifier fuse blows. Deter-
refer to this information in the event of an
mine and resolve the cause, then replace the
insurance claim such as loss or theft.
fuse with and identical equivalent.
2
En
Section
Before you start
01
English
! Always install the amplifier on a flat surface.
If the nominal input and impedance are out of
Do not install the amplifier on a surface that
the above ranges, the subwoofer may catch
is not flat or on a surface with a protrusion.
fire, emit smoke or become damaged.
Doing so could result in malfunction.
About the protection function
! When installing the amplifier, do not allow
This product has protection function. When this
parts such as extra screws to get caught be-
product detects something abnormal, the follow-
tween the amplifier and the automobile.
ing functions will operate to protect the product
Doing so could cause malfunction.
and speaker output.
! Do not allow this unit to come into contact
! The POWER/PROTECT indicator will turn red
with liquids. Electrical shock could result.
and the amplifier will shut down in the situa-
Also, damage to this unit, smoke, and over-
tions outlined below.
heating could result from contact with liquids.
— If the temperature inside the amplifier gets
The surfaces of the amplifier and any attached
too high.
speakers may also heat up and cause minor
— If a DC voltage is applied to the speaker
burns.
output terminal.
! In the event of any abnormality, the power
! The POWER/PROTECT indicator will turn red
supply to the amplifier is cut off to prevent
and the output will be muted in the situations
equipment malfunction. If this occurs, switch
outlined below.
the system power off and check the power
— If the speaker output terminal and speaker
supply and speaker connections. If you are un-
wire are short-circuited.
able to determine the cause, please contact
your dealer.
! Always disconnect the negative * terminal of
the battery beforehand to avoid the risk of
electric shock or short circuit during installa-
tion.
! Do not attempt to disassemble or modify this
unit. Doing so may result in fire, electric
shock or other malfunction.
CAUTION
! Always keep the volume low enough to hear
outside sounds.
! Extended use of the car stereo while the en-
gine is at rest or idling may exhaust the bat-
tery.
! Connect either of three subwoofers to the am-
plifier; 1: a subwoofer with a 300 W (GM-
D8601) / 500 W (GM-D9601) or larger nominal
input and an impedance 4 W, 2: a subwoofer
with a 500 W (GM-D8601) / 800 W (GM-D9601)
or larger nominal input and an impedance 2 W
or 3: a subwoofer with a 800 W (GM-D8601) /
1 200 W (GM-D9601) or larger nominal input
and an impedance 1 W.
3
En
Section
02
Setting the unit
stereo volume is turned up, turn these con-
What’s what
trols to higher level.
GM-D8601
! For use with an RCA equipped car stereo
Front side
(standard output of 500 mV), set to the
21 3 4
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with maxi-
mum output of 4 V or more, adjust level
to match that of the car stereo output.
! For use with an RCA equipped car stereo
with output of 4 V, set to the H position.
! If you hear too much noise when using
the speaker input terminals, turn the
Rear side
gain control to higher level.
3 LPF (low-pass filter) cut off frequency
control
You can select a cut off frequency from
40 Hz to 240 Hz.
GM-D9601
Front side
4 BASS BOOST REMOTE (bass boost level
remote control) jack
21 3 4
By connecting the Bass boost level remote
control to the jack on the main unit, you will
be able to select a bass boost level from
0 dB to 18 dB.
For instruction of connecting the bass boost
remote control to the amplifier, see the Con-
nection diagram on page 6.
Rear side
Setting gain properly
! Protective function included to prevent
malfunction of the unit and/or speakers
To adjust the switch, use a flathead screwdri-
due to excessive output, improper use or
ver if needed.
improper connection.
! When outputting high volume sound etc.,
1 POWER/PROTECT indicator
this function cuts off the output for a few
The power indicator lights up to indicate
seconds as a normal function, but output
power ON.
is restored when the volume of the head
! If something is not normal, the indicator
unit is turned down.
turns red.
2 GAIN (gain) control
If output remains low, even when the car
stereo volume is turned up, turn controls to
lower level. If distortion occurs when the car
4
En
Section
Setting the unit
02
English
! A cut in sound output may indicate impro-
Signal waveform when outputting at
per setting of the gain control. To ensure
high volume using amplifier gain
continuous sound output with the head
control
unit at a high volume, set amplifier gain
control to a level appropriate for the preout
maximum output level of the head unit, so
that volume can remain unchanged and to
control excess output.
! Despite correct volume and gain settings,
the unit sound still cuts out periodically. In
such cases, please contact the nearest
Signal waveform distorted with high output, if
authorized Pioneer Service Station.
you raise the gain of the amplifier the power
changes only slightly.
Gain control of this unit
Preout level: 2 V (Standard: 500 mV)
Preout level: 4 V
Above illustration shows NORMAL gain set-
ting.
Relationship between amplifier gain
and head unit output power
If amplifier gain is raised improperly, this will
simply increase distortion, with little increase
in power.
5
En
Оглавление
- Before you start
- Setting the unit
- Connecting the units
- Connecting the units Connections when using Solderless terminal the speaker input wire connections
- Connecting the units
- Installation Before installing the amplifier Attaching the Bass boost remote control
- Installation
- Additional information
- Avant de commencer
- Réglage de l’appareil
- Connexion des appareils
- Installation
- Informations complémentaires
- Prima di iniziare
- Impostazione dell’unità
- Collegamento delle unità
- Installazione
- Informazioni supplementari
- Antes de comenzar
- Configuración de la unidad
- Conexión de las unidades
- Instalación
- Información adicional
- Bevor Sie beginnen
- Einstellen des Geräts
- Anschließen der Geräte
- Installation
- Zusätzliche Informationen
- Vóór u begint
- Het toestel installeren
- De toestellen aansluiten
- De toestellen aansluiten Aansluiting via de luidspre- Aansluitingen niet solderen keringangskabel
- De toestellen aansluiten
- Installatie
- Aanvullende informatie
- Перед началом эксплуатации
- Настройка усилителя
- Подключение устройств
- Установка
- Установка Пример установки усилителя на напольном коврике или шасси
- Дополнительная информация