Pioneer GM-D9601: Setting the unit
Setting the unit: Pioneer GM-D9601
Section
02
Setting the unit
stereo volume is turned up, turn these con-
What’s what
trols to higher level.
GM-D8601
! For use with an RCA equipped car stereo
Front side
(standard output of 500 mV), set to the
21 3 4
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with maxi-
mum output of 4 V or more, adjust level
to match that of the car stereo output.
! For use with an RCA equipped car stereo
with output of 4 V, set to the H position.
! If you hear too much noise when using
the speaker input terminals, turn the
Rear side
gain control to higher level.
3 LPF (low-pass filter) cut off frequency
control
You can select a cut off frequency from
40 Hz to 240 Hz.
GM-D9601
Front side
4 BASS BOOST REMOTE (bass boost level
remote control) jack
21 3 4
By connecting the Bass boost level remote
control to the jack on the main unit, you will
be able to select a bass boost level from
0 dB to 18 dB.
For instruction of connecting the bass boost
remote control to the amplifier, see the Con-
nection diagram on page 6.
Rear side
Setting gain properly
! Protective function included to prevent
malfunction of the unit and/or speakers
To adjust the switch, use a flathead screwdri-
due to excessive output, improper use or
ver if needed.
improper connection.
! When outputting high volume sound etc.,
1 POWER/PROTECT indicator
this function cuts off the output for a few
The power indicator lights up to indicate
seconds as a normal function, but output
power ON.
is restored when the volume of the head
! If something is not normal, the indicator
unit is turned down.
turns red.
2 GAIN (gain) control
If output remains low, even when the car
stereo volume is turned up, turn controls to
lower level. If distortion occurs when the car
4
En
Section
Setting the unit
02
English
! A cut in sound output may indicate impro-
Signal waveform when outputting at
per setting of the gain control. To ensure
high volume using amplifier gain
continuous sound output with the head
control
unit at a high volume, set amplifier gain
control to a level appropriate for the preout
maximum output level of the head unit, so
that volume can remain unchanged and to
control excess output.
! Despite correct volume and gain settings,
the unit sound still cuts out periodically. In
such cases, please contact the nearest
Signal waveform distorted with high output, if
authorized Pioneer Service Station.
you raise the gain of the amplifier the power
changes only slightly.
Gain control of this unit
Preout level: 2 V (Standard: 500 mV)
Preout level: 4 V
Above illustration shows NORMAL gain set-
ting.
Relationship between amplifier gain
and head unit output power
If amplifier gain is raised improperly, this will
simply increase distortion, with little increase
in power.
5
En
Оглавление
- Before you start
- Setting the unit
- Connecting the units
- Connecting the units Connections when using Solderless terminal the speaker input wire connections
- Connecting the units
- Installation Before installing the amplifier Attaching the Bass boost remote control
- Installation
- Additional information
- Avant de commencer
- Réglage de l’appareil
- Connexion des appareils
- Installation
- Informations complémentaires
- Prima di iniziare
- Impostazione dell’unità
- Collegamento delle unità
- Installazione
- Informazioni supplementari
- Antes de comenzar
- Configuración de la unidad
- Conexión de las unidades
- Instalación
- Información adicional
- Bevor Sie beginnen
- Einstellen des Geräts
- Anschließen der Geräte
- Installation
- Zusätzliche Informationen
- Vóór u begint
- Het toestel installeren
- De toestellen aansluiten
- De toestellen aansluiten Aansluiting via de luidspre- Aansluitingen niet solderen keringangskabel
- De toestellen aansluiten
- Installatie
- Aanvullende informatie
- Перед началом эксплуатации
- Настройка усилителя
- Подключение устройств
- Установка
- Установка Пример установки усилителя на напольном коврике или шасси
- Дополнительная информация