Pioneer A-50-K: инструкция

A70_SYXE8.book 1 ページ ２０１２年７月２７日　金曜日　午後６時５３分

Operating Instructions | Mode d’emploi | Bedienungsanleitung |

Istruzioni per I’uso | Handleiding | Manual de instrucciones |

Инструкции по эксплуатации

ME06

A-70-K/-S

Integrated Amplifier | Amplificateur Intégré |

Eingebauter Verstärker | Amplificatore Integrato |

Geïntegreerde versterker | Amplificador integrado |

Интегральный усилитель

A-

50-K/-S

A70_SYXE8.book 2 ページ ２０１２年７月２７日　金曜日　午後６時５３分

WARNING

IMPORTANT

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

CAUTION

liquid near this equipment (such as a vase or flower

RISK OF ELECTRIC SHOCK

pot) or expose it to dripping, splashing, rain or

DO NOT OPEN

moisture.

D3-4-2-1-3_A1_En

The lightning flash with arrowhead symbol,

CAUTION:

The exclamation point within an equilateral

within an equilateral triangle, is intended to

TO PREVENT THE RISK OF ELECTRIC

triangle is intended to alert the user to the

alert the user to the presence of uninsulated

SHOCK, DO NOT REMOVE COVER (OR

presence of important operating and

WARNING

“dangerous voltage” within the product’s

BACK). NO USER-SERVICEABLE PARTS

maintenance (servicing) instructions in the

Before plugging in for the first time, read the following

enclosure that may be of sufficient

INSIDE. REFER SERVICING TO QUALIFIED

literature accompanying the appliance.

magnitude to constitute a risk of electric

SERVICE PERSONNEL.

section carefully.

shock to persons.

D3-4-2-1-1_A1_En

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

Information for users on collection and disposal of old equipment and used batteries

D3-4-2-1-4*_A1_En

Symbol for

These symbols on the products, packaging, and/or accompanying documents mean

equipment

that used electrical and electronic products and batteries should not be mixed with

WARNING

general household waste.

To prevent a fire hazard, do not place any naked flame

For proper treatment, recovery and recycling of old products and used batteries,

sources (such as a lighted candle) on the equipment.

please take them to applicable collection points in accordance with your national

D3-4-2-1-7a_A1_En

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

VENTILATION CAUTION

Symbol examples

resources and prevent any potential negative effects on human health and the

When installing this unit, make sure to leave space

for batteries

environment which could otherwise arise from inappropriate waste handling.

around the unit for ventilation to improve heat radiation

For more information about collection and recycling of old products and batteries,

(at least 30 cm at top, 10 cm at rear, and 10 cm at each

please contact your local municipality, your waste disposal service or the point of sale

side).

where you purchased the items.

WARNING

These symbols are only valid in the European Union.

Slots and openings in the cabinet are provided for

For countries outside the European Union:

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

If you wish to discard these items, please contact your local authorities or dealer and

hazard, the openings should never be blocked or

ask for the correct method of disposal.

covered with items (such as newspapers, table-cloths,

Pb

K058a_A1_En

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

A70_SYXE8.book 3 ページ ２０１２年７月２７日　金曜日　午後６時５３分

Operating Environment

Thank you for buying this Pioneer

This product is for general household purposes. Any

Operating environment temperature and humidity:

product.

failure due to use for other than household purposes

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

Please read through these operating instructions so that

(such as long-term use for business purposes in a

you will know how to operate your model properly. After

(cooling vents not blocked)

restaurant or use in a car or ship) and which requires

you have finished reading the instructions, put them in a

Do not install this unit in a poorly ventilated area, or in

repair will be charged for even during the warranty

safe place for future reference.

locations exposed to high humidity or direct sunlight (or

period.

strong artificial light)

K041_A1_En

D3-4-2-1-7c*_A1_En

Contents

If the AC plug of this unit does not match the AC

POWER-CORD CAUTION

outlet you want to use, the plug must be removed

Handle the power cord by the plug. Do not pull out the

01 Before you start

and appropriate one fitted. Replacement and

plug by tugging the cord and never touch the power

What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . .4

cord when your hands are wet as this could cause a

Loading the batteries in the remote control . . . . . .4

mounting of an AC plug on the power supply cord of

Using the remote control. . . . . . . . . . . . . . . . . . . . .4

this unit should be performed only by qualified

short circuit or electric shock. Do not place the unit, a

Installing the amplifier. . . . . . . . . . . . . . . . . . . . . .4

service personnel. If connected to an AC outlet, the

piece of furniture, etc., on the power cord, or pinch the

cut-off plug can cause severe electrical shock. Make

cord. Never make a knot in the cord or tie it with other

02 Connecting up

cords. The power cords should be routed such that they

Making cable connections. . . . . . . . . . . . . . . . . . .5

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

are not likely to be stepped on. A damaged power cord

About “Bi-wiring” . . . . . . . . . . . . . . . . . . . . . . . . . . 5

can cause a fire or give you an electrical shock. Check

Connecting speaker cables . . . . . . . . . . . . . . . . . . 6

the mains plug from the wall socket when left unused

Connecting audio cables . . . . . . . . . . . . . . . . . . . .6

for a long period of time (for example, when on

the power cord once in a while. When you find it

Using centralized control with other Pioneer

vacation).

damaged, ask your nearest PIONEER authorized

components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

D3-4-2-2-1a_A1_En

service center or your dealer for a replacement.

Digital audio input connections (A-70 only) . . . . . .6

S002*_A1_En

Using a USB cable to connect to a computer

(A-70 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

CAUTION

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

The /I STANDBY/ON switch on this unit will not

03 Controls and displays

completely shut off all power from the AC outlet.

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Since the power cord serves as the main disconnect

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

device for the unit, you will need to unplug it from the

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . .10

AC outlet to shut down all power. Therefore, make

04 Operation

sure the unit has been installed so that the power

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

cord can be easily unplugged from the AC outlet in

Set the power to Standby. . . . . . . . . . . . . . . . . . . .11

case of an accident. To avoid fire hazard, the power

When using the unit as a power amplifier . . . . . . .11

cord should also be unplugged from the AC outlet

Playing music from a digital audio component

when left unused for a long period of time (for

(A-70 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Playing music from a computer (A-70 only) . . . . . .12

example, when on vacation).

D3-4-2-2-2a*_A1_En

Making an audio recording . . . . . . . . . . . . . . . . .12

To set for automatic standby status

(Auto Power Down) . . . . . . . . . . . . . . . . . . . . . . . 13

Restoring all the settings to the factory default

settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

05 Additional information

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .14

Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3

01 Before you start

Chapter 1:

Using the remote control

The remote has a range of about 7 m at an angle of about

30º from the remote sensor.

Before you start

The batteries included with the unit have been provided

to allow you check product operation and may not last

What’s in the box

long. We recommend using alkaline batteries that have

Please confirm that the following accessories are in the

a longer life.

box when you open it.

•Remote control

WARNING

• AAA/IEC R03 dry cell batteries x2

• Short pin plug x 2

• Do not use or store batteries in direct sunlight or

(At time of purchase, these plugs have been factory

other excessively hot place, such as inside a car or

installed in the rear panel’s PHONO IN terminals.)

near a heater. This can cause batteries to leak,

• Power cord (Length: 1.8 m)

overheat, explode or catch fire. It can also reduce

• Warranty card

the life or performance of batteries.

Keep in mind the following when using the remote

• Caution sheet (To first-time users)

Caution

control:

• Operating instructions (This document)

• Make sure that there are no obstacles between the

Incorrect use of batteries may result in such hazards as

remote and the remote sensor on the unit.

Note

leakage and bursting. Observe the following

• Remote operation may become unreliable if strong

precautions:

• Illustrations featured in the Operating Instructions

sunlight or fluorescent light is shining on the unit’s

may have been modified or simplified for ease of

• When inserting the batteries, make sure not to

remote sensor.

explanation, and may therefore differ from the

damage the springs on the battery’s  terminals.

• Remote controllers for different devices can

interfere with each other. Avoid using remotes for

actual product appearance.

This can cause batteries to leak or overheat.

• The illustrations used here are mainly of the A-70.

• Do not use any batteries other than the ones

other equipment located close to this unit.

specified. Also, do not use a new battery together

• Replace the batteries when you notice a fall off in

with an old one.

the operating range of the remote.

• When loading the batteries into the remote control,

Loading the batteries in the remote

set them in the proper direction, as indicated by the

polarity marks ( and ).

control

• Do not heat batteries, disassemble them, or throw

Installing the amplifier

them into flames or water.

When installing this unit, make sure to put it on a level

• Batteries may have different voltages, even if they

and stable surface.

are the same size and shape. Do not use different

• Don’t install it on the following places:

types of batteries together.

– on a color TV (the screen may distort)

1

2

• To prevent leakage of battery fluid, remove the

batteries if you do not plan to use the remote

– near a cassette deck (or close to a device that

control for a long period of time (1 month or more).

gives off a magnetic field). This may interfere with

If the fluid should leak, wipe it carefully off the

the sound.

inside of the case, then insert new batteries. If a

– in direct sunlight

battery should leak and the fluid should get on your

– in damp or wet areas

3

skin, flush it off with large quantities of water.

– in extremely hot or cold areas

• When disposing of used batteries, please comply

– in places where there is vibration or other

with governmental regulations or environmental

1 Open the rear lid.

movement

public institution’s rules that apply in your country/

– in places that are very dusty

area.

2 Insert the new batteries, matching the

– in places that have hot fumes or oils (such as a

kitchen)

polarities as indicated inside the case.

• Do not mount the unit on a sofa or other object or

3 Close the rear lid.

material with absorbent qualities, since sound

quality may be adversely affected.

4

En

A70_SYXE8.book 4 ページ ２０１２年７月２７日　金曜日　午後６時５３分

Connecting up 02

English

Chapter 2:

Connecting up

Making cable connections

Caution

• Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

• Connect the power cord after all the connections between devices have been completed.

DeutschFrançais

RL

OUTPUT

AUDIO

PLAY

REC

L

R

Italiano Español Русский

AUX IN

Nederlands

PRE OUT

L

R

OUTPUT

L

L

R

R

5

En

R

L

R

L

L

L

R

R

L

R

L

R

R

L

R

L

R

L

R

L

L

R

Settings>

Music>

Backlight

Shuffle Songs

Extras>

iPod

MENU





R

L

R

L

R

L

ADVANCED

MCACC

FL OFF

iPod iPhone iPadHDMI

INPUT

SELECTOR

STANDBY/ON

MASTER

VOLUME

• iPod is a trademark of Apple Inc., registered in the

Caution

U.S. and other countries.

•The SIGNAL GND terminal is provided to reduce

noise when connecting the unit to components

such as an analog turntable.

About “Bi-wiring”

•The PHONO IN terminals are factory equipped with

short pin plugs. These should not be removed

This unit can be used with speakers that support bi-

except when connecting a turntable. Be sure to

wiring. Be sure to connect the high-frequency and

save the short pin plugs in a safe place.

low-frequency connections correctly.

• Do not insert the short pin plugs in any connectors

• During playback, be sure that both the SPEAKERS

other than the PHONO IN terminals. Connecting

A button and SPEAKERS B button are set to ON

them to any other terminals may cause

(page 8).

malfunctions.

• Do not connect the PHONO IN terminals to any

component other than a turntable; also, do not

connect to a turntable equipped with built-in

equalizer. An excessively high sound output may be

produced, resulting in damage to your speakers or

other devices.

• The A-50’s PHONO IN terminals are designed to be

used only with turntables equipped with MM

(moving-magnet) type cartridges. Turntables

equipped with MC (moving-coil) cartridges cannot

be used.

• Make sure not to bend the cables over the top of

this unit (as shown in the illustration). If this

happens, the magnetic field produced by the

transformers in this unit may cause a humming

noise from the speakers.

• The unit’s POWER AMP DIRECT terminals should

never be connected to any other component’s

connectors except PRE-AMP OUT.

• If your turntable has a grounding wire, secure it to

the ground terminal on this amplifier.

Note

Caution

• When connecting a tape cassette deck, playback

noise may be heard, depending on the installation

• When using bi-wiring to connect speakers, avoid

location. This noise is caused by leakage flux from

adverse affects on the amplifier by being sure to

the amplifier’s transformer. In this event, change

remove the HIGH and LOW short bars provided

the installation location, or move the deck farther

with the speakers. For detailed information, consult

from the amplifier.

the instructions provided with the speakers.

A70_SYXE8.book 5 ページ ２０１２年７月２７日　金曜日　午後６時５３分

02 Connecting up

• When using speakers with removable network

circuits, note that if the network is removed, no

Connecting audio cables

effect will be produced and damage may be caused

to the speaker.

Connect the white plug to the left (L) jack, and the red

• Another method of connection is to connect the

plug to the right (R) jack. Be sure to insert the plugs fully

SPEAKERS A terminals to HIGH and the SPEAKERS

into the jacks.

B terminals to LOW (reverse that shown in the

illustration).

Connecting speaker cables

1 Twist the cable cores.

2 Loosen the nut on the

SPEAKERS

terminal, and insert the speaker cable into

the exposed hole in the terminal shaft.

3 Retighten the terminal nut.

123

Caution

• When using only one set of speaker terminals

(SPEAKERS A or SPEAKERS B), or when utilizing

bi-wiring connections, the speaker used should

have a nominal impedance between 4 Ω and

16 Ω. When using both sets of terminals, the

connected speakers should have nominal

impedance between 8 Ω and 32 Ω. Consult the

instructions accompanying your speakers for

details regarding the impedance value.

• Make sure the positive and negative (+/–) terminals

on the amplifier match those on the speakers.

• These speaker terminals carry HAZARDOUS live

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker

terminal. If any of the bare speaker wire touches the

back panel it may cause the power to cut off as a

safety measure.

6

En

Using centralized control with other

Digital audio input connections (A-70

Pioneer components

only)

Multiple Pioneer components equipped with CONTROL

If a coaxial digital cable (sold separately) is used to

IN/OUT jacks can be connected to the unit, allowing

connect this unit’s DIGITAL IN COAXIAL terminal to the

centralized control of the components via the remote

digital audio output connector of a digital audio playback

sensor on the unit. This also allows remote control of

component, the playback component can be used to

components not equipped with a remote sensor, or

play music through this unit.

installed in places where the component’s remote

For more information regarding the output of audio

sensor cannot be accessed.

signals input to the DIGITAL IN COAXIAL terminal,

consult page 12.

IN

OUT

CONTROL

Note

• For connections use a commercially available

Note

monaural miniplug cord (without resistor).

• When connecting the CONTROL IN/OUT jacks,

• Digital signal formats that can be input to this unit

commercially available audio cords must also be

include linear PCM signals with sampling rate and

used to make analog connections. Merely

quantitative bits up to 192 kHz/32 bits. (Depending

connecting the CONTROL IN/OUT jacks alone will

on the connected device and environment,

not allow proper system control.

operation may not be successful).

• When a control cord is connected to the unit’s

CONTROL IN jack, the unit cannot be controlled by

pointing the remote control at the unit (the remote

sensor is automatically disabled).

A70_SYXE8.book 6 ページ ２０１２年７月２７日　金曜日　午後６時５３分

Connecting up 02

English

Using a USB cable to connect to a

Plugging in

computer (A-70 only)

If a USB cable (sold separately) is used to connect this

unit’s DIGITAL IN USB terminal to a computer’s USB

Important

port, music files located on the computer can be played

• When going on a trip or otherwise not using the

through this unit.

unit for an extended period, always disconnect the

For more information regarding the output of audio

power cord from its outlet. Note that various

signals input to the DIGITAL IN USB terminal, consult

internal settings will not be lost even if the power

page 12.

cord is disconnected from its outlet for an extended

time.

Important

• If it is necessary to detach the power cord, first be

sure to press the 

/I

STANDBY/ON button on the

• When using this connection to input audio files

front panel of the unit so the unit is turned OFF

from a computer to this unit, it may be necessary to

before detaching the cord.

DeutschFrançais

install a special driver on the computer. For details,

see the website of Pioneer.

Caution

• The use of a power cord other than the one provided

USB

will invalidate the warranty, since Pioneer will not

be responsible for any damage incurred. (The

power cord provided with the unit has a rated

current capacity of 10 A.)

Italiano Español Русский

• Do not use any power cord other than the one

supplied with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

After you’ve finished making all connections, plug the

unit into an AC outlet.

Nederlands

1 Plug the supplied power cord into the

Note

AC IN

socket on the rear panel of the unit.

• This unit cannot be used to play audio files from a

2 Plug the other end into an AC outlet.

computer unless Media Player is installed on the

connected computer.

7

En

A70_SYXE8.book 7 ページ ２０１２年７月２７日　金曜日　午後６時５３分

A70_SYXE8.book 8 ページ ２０１２年７月２７日　金曜日　午後６時５３分

03 Controls and displays

Chapter 3:

6 Remote sensor

14

CARTRIDGE

select switch (A-70 only)

Receives the signals from the remote control (page 4).

Select the type of cartridge used with your turntable.

Controls and displays

7

PHONES

jack

15

POWER AMP DIRECT

button/indicator

Use to connect headphones. No sound is produced

Press this button when the unit is to be used as a power

when the POWER AMP DIRECT button is ON.

amplifier (page 11).

Front panel

8 DIRECT button/indicator

16

INPUT SELECTOR

knob/indicators

On : The indicator lights: When this button is set to ON,

Turn the knob clockwise or counterclockwise so that the

2 54

31

sound signals are output directly, without being passed

indicator lights for your desired input source. Turning

A-70

through the various adjustment circuits (BASS, TREBLE,

the knob clockwise causes the lit indicator to right.

BALANCE, LOUDNESS). This allows reproduction of the

Turning counterclockwise causes it to left. When the

signals with greater fidelity, but it disables any settings

remote control’s MUTE button is pressed to mute the

made with the BASS, TREBLE, BALANCE or LOUDNESS

sound, the indicator for the input source selected with

controls.

the INPUT SELECTOR knob flashes.

Off : The indicator goes off: The signal passes through

the various frequency adjusting circuits. When the

indicator is OFF, adjustments can be made with the

BASS, TREBLE, BALANCE, and LOUDNESS controls.

9

BASS

tone control

Use to adjust the low-frequency tone. The center position

is the flat (normal) position. When turned to the right,

6

7

8

9

10 11 13 15

14 1612

low-frequency tones are emphasized; when turned to the

left, low-frequency tones are de-emphasized.

1



/I

STANDBY/ON

4

SPEAKERS B

button/indicator

• This button does not operate when the DIRECT

Switches the amplifier between off and on.

Use this button to listen to the speaker system

button is in the on position.

When power is turned on, the power indicator in the

connected to SPEAKERS B terminals.

10

TREBLE

tone control

center of the button will light.

On : The indicator lights. Sound is heard from the

Use to adjust the high-frequency tone. The center

speaker system. (Sound will also be produced from the

position is the flat (normal) position. When turned to the

2

STANDBY/APD

indicator

PHONES jack.)

right, high-frequency tones are emphasized; when

When power is set to standby, the indicator lights red.

Off : The indicator goes off. No sound is heard from the

turned to the left, high-frequency tones are de-

When the Auto Power Down (APD) function is on, the

speaker system. Set to this position when listening with

emphasized.

indicator lights green (page 13).

headphones.

• This button does not operate when the DIRECT

3

SPEAKERS A

button/indicator

button is in the on position.

5

LOUDNESS

button/indicator

Use this button to listen to the speaker system

Use when listening at low volume levels.

connected to SPEAKERS A terminals.

11

BALANCE

control

On : The indicator lights: Boosts low and high

Should normally be left in the center position. Adjust

On : The indicator lights. Sound is heard from the

frequencies to give added punch to playback even at a

balance if the sound is louder from one of the speakers.

speaker system. (Sound will also be produced from the

low volume level.

If the right side is louder, turn toward the L (left) position

PHONES jack.)

Off : The indicator goes off: Should normally be left in

and if the left side is louder, turn toward the R (right)

Off : The indicator goes off. No sound is heard from the

this position.

position.

speaker system. Set to this position when listening with

• This button does not operate when the DIRECT

• This button does not operate when the DIRECT

headphones.

button is in the on position.

button is in the on position.

• When sound volume is raised, the amount of

12

ATTENUATOR

button (A-70 only)

change produced by the LOUDNESS circuit is

Press when you wish to make fine adjustments to the

reduced.

sound volume when playing at very low sound volume

levels.

13 VOLUME control

Use to adjust the volume level. (Also allows adjustment

of the headphone sound volume.)

8

En

Controls and displays 03

English

Rear panel

See pages 5-7 for details regarding connections.

DeutschFrançais

1

PHONO IN (MM/MC)

terminals (A-70)

9 GND (Turntable ground) terminal

PHONO IN (MM) terminals (A-50)

This ground terminal is designed to help reduce noise

when a turntable is connected. It is not a safety ground.

Italiano Español Русский

2

AUX

IN

terminals (A-50 only)

10

SACD/CD

IN

terminals

3

RECORDER IN/OUT

terminals

11

NETWORK

IN

terminals

4

DIGITAL IN USB

terminal (A-70 only)

12

TUNER

IN

terminals

5

SPEAKERS A

terminals (Right channel)

13

POWER AMP DIRECT

IN

terminals

6

SPEAKERS B

terminals (Right channel)

When using the unit as a power amplifier, connect the

Nederlands

pre-amplifier here (page 11).

7

SPEAKERS B

terminals (Left channel)

14

DIGITAL IN COAXIAL

terminal (A-70

8

SPEAKERS A

terminals (Left channel)

only)

15

CONTROL IN/OUT

jack

16

AC IN

jack

Connect power cord to here and an AC wall socket.

9

En

A70_SYXE8.book 9 ページ ２０１２年７月２７日　金曜日　午後６時５３分

A70_SYXE8-FR.book Page 2 Monday, July 30, 2012 9:07 AM

AVERTISSEMENT

IMPORTANT

Cet appareil n’est pas étanche. Pour éviter les risques

d’incendie et de décharge électrique, ne placez près de

ATTENTION

lui un récipient rempli d’eau, tel qu’un vase ou un pot

DANGER D´ELECTROCUTION

de fleurs, et ne l’exposez pas à des gouttes d’eau, des

NE PAS OUVRIR

éclaboussures, de la pluie ou de l’humidité.

Ce symbole de l’éclair, placé dans un

ATTENTION :

Ce point d’exclamation, placé dans un

D3-4-2-1-3_A1_Fr

triangle équilatéral, a pour but d’attirer

POUR ÉVITER TOUT RISQUE

triangle équilatéral, a pour but d’attirer

l’attention de l’utilisateur sur la présence, à

D’ÉLECTROCUTION, NE PAS ENLEVER LE

l’attention de l’utilisateur sur la présence,

l’intérieur du coffret de l’appareil, de

COUVERCLE (NI LE PANNEAU ARRIÈRE).

AVERTISSEMENT

dans les documents qui accompagnent

“tensions dangereuses” non isolées d’une

AUCUNE PIÈCE RÉPARABLE PAR

l’appareil, d’explications importantes du

Avant de brancher l’appareil pour la première, lisez

grandeur suffisante pour représenter un

L’UTILISATEUR NE SE TROUVE À

point de vue de l’exploitation ou de

attentivement la section suivante.

risque d’électrocution pour les êtres

L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À

l’entretien.

La tension de l’alimentation électrique disponible

humains.

UN PERSONNEL QUALIFIÉ UNIQUEMENT.

varie selon le pays ou la région. Assurez-vous que

D3-4-2-1-1_A1_Fr

la tension du secteur de la région où l’appareil sera

utilisé correspond à la tension requise (par ex. 230

V ou 120 V), indiquée sur le panneau arrière.

Information à destination des utilisateurs sur la collecte et l’élimination des

D3-4-2-1-4*_A1_Fr

équipements et batteries usagés

Marquage pour les

Ces symboles qui figurent sur les produits, les emballages et/ou les documents

AVERTISSEMENT

équipements

d’accompagnement signifient que les équipements électriques et électroniques et

Pour éviter les risques d’incendie, ne placez aucune

batteries usagés ne doivent pas être jetés avec les déchets ménagers et font l’objet

flamme nue (telle qu’une bougie allumée) sur

d’une collecte sélective.

l’appareil.

Pour assurer l’enlèvement et le traitement appropriés des produits et batteries

D3-4-2-1-7a_A1_Fr

usagés, merci de les retourner dans les points de collecte sélective habilités

conformément à la législation locale en vigueur.

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un

Exemples de marquage

En respectant les circuits de collecte sélective mis en place pour ces produits, vous

espace suffisant autour de ses parois de manière à

pour les batteries

contribuerez à économiser des ressources précieuses et à prévenir les impacts

améliorer la dissipation de chaleur (au moins 30 cm sur

négatifs éventuels sur la santé humaine et l’environnement qui pourraient résulter

le dessus, 10 cm à l’arrière et 10 cm de chaque côté).

d’une mauvaise gestion des déchets.

AVERTISSEMENT

Pour plus d’information sur la collecte et le traitement des produits et batteries

Les fentes et ouvertures du coffret sont prévues pour la

usagés, veuillez contacter votre municipalité, votre service de gestion des déchets

ventilation, pour assurer un fonctionnement stable de

ou le point de vente chez qui vous avez acheté ces produits.

l’appareil et pour éviter sa surchauffe. Pour éviter les

Ces symboles ne sont valables que dans les pays de l’Union Européenne.

risques d’incendie, ne bouchez jamais les ouvertures et

Pour les pays n’appartenant pas à l’Union Européenne :

ne les recouvrez pas d’objets, tels que journaux, nappes

ou rideaux, et n’utilisez pas l’appareil posé sur un tapis

Pb

Si vous souhaitez jeter ces articles, veuillez contacter les autorités ou revendeurs

épais ou un lit.

locaux pour connaître les méthodes d’élimination appropriées.

D3-4-2-1-7b*_A1_Fr

K058a_A1_Fr