Pioneer A-10-K: инструкция

A30_SYXE8_cover_anki.fm 1 ページ ２０１２年２月２１日　火曜日　午後１時４２分

Operating Instructions | Mode d’emploi | Bedienungsanleitung |

Istruzioni per I’uso | Handleiding | Manual de instrucciones |

Инструкции по эксплуатации

A-

30-K/-S

ME06

A-20-K/-S

Integrated Amplifier | Amplificateur Intégré |

Eingebauter Verstärker | Amplificatore Integrato |

Geïntegreerde versterker | Amplificador integrado |

A-

10 -K/-S

A30_SYXE8.book 2 ページ ２０１２年２月１６日　木曜日　午前８時５８分

WARNING

IMPORTANT

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

CAUTION

liquid near this equipment (such as a vase or flower

RISK OF ELECTRIC SHOCK

pot) or expose it to dripping, splashing, rain or

DO NOT OPEN

moisture.

D3-4-2-1-3_A1_En

The lightning flash with arrowhead symbol,

CAUTION:

The exclamation point within an equilateral

within an equilateral triangle, is intended to

TO PREVENT THE RISK OF ELECTRIC

triangle is intended to alert the user to the

alert the user to the presence of uninsulated

SHOCK, DO NOT REMOVE COVER (OR

presence of important operating and

WARNING

“dangerous voltage” within the product’s

BACK). NO USER-SERVICEABLE PARTS

maintenance (servicing) instructions in the

Before plugging in for the first time, read the following

enclosure that may be of sufficient

INSIDE. REFER SERVICING TO QUALIFIED

literature accompanying the appliance.

magnitude to constitute a risk of electric

SERVICE PERSONNEL.

section carefully.

shock to persons.

D3-4-2-1-1_A1_En

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

European model only

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

Information for users on collection and disposal of old equipment and used batteries

D3-4-2-1-4*_A1_En

Symbol for

These symbols on the products, packaging, and/or accompanying documents mean

equipment

that used electrical and electronic products and batteries should not be mixed with

WARNING

general household waste.

To prevent a fire hazard, do not place any naked flame

For proper treatment, recovery and recycling of old products and used batteries,

sources (such as a lighted candle) on the equipment.

please take them to applicable collection points in accordance with your national

D3-4-2-1-7a_A1_En

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

VENTILATION CAUTION

Symbol examples

resources and prevent any potential negative effects on human health and the

When installing this unit, make sure to leave space

for batteries

environment which could otherwise arise from inappropriate waste handling.

around the unit for ventilation to improve heat radiation

For more information about collection and recycling of old products and batteries,

(at least 30 cm at top, 10 cm at rear, and 10 cm at each

please contact your local municipality, your waste disposal service or the point of sale

side).

where you purchased the items.

WARNING

These symbols are only valid in the European Union.

Slots and openings in the cabinet are provided for

For countries outside the European Union:

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

If you wish to discard these items, please contact your local authorities or dealer and

hazard, the openings should never be blocked or

ask for the correct method of disposal.

covered with items (such as newspapers, table-cloths,

Pb

K058a_A1_En

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

A30_SYXE8.book 3 ページ ２０１２年２月１６日　木曜日　午前８時５８分

Operating Environment

Thank you for buying this Pioneer

This product is for general household purposes. Any

Operating environment temperature and humidity:

product.

failure due to use for other than household purposes

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

Please read through these operating instructions so that

(such as long-term use for business purposes in a

you will know how to operate your model properly. After

(cooling vents not blocked)

restaurant or use in a car or ship) and which requires

you have finished reading the instructions, put them in a

Do not install this unit in a poorly ventilated area, or in

repair will be charged for even during the warranty

safe place for future reference.

locations exposed to high humidity or direct sunlight (or

period.

strong artificial light)

K041_A1_En

D3-4-2-1-7c*_A1_En

Contents

If the AC plug of this unit does not match the AC

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

01 Before you start

outlet you want to use, the plug must be removed

What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . .4

and appropriate one fitted. Replacement and

plug by tugging the cord and never touch the power

mounting of an AC plug on the power supply cord of

cord when your hands are wet as this could cause a

Loading the batteries in the remote control

(Except A-10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

this unit should be performed only by qualified

short circuit or electric shock. Do not place the unit, a

Using the remote control. . . . . . . . . . . . . . . . . . . . .4

service personnel. If connected to an AC outlet, the

piece of furniture, etc., on the power cord, or pinch the

Installing the amplifier. . . . . . . . . . . . . . . . . . . . . . 4

cut-off plug can cause severe electrical shock. Make

cord. Never make a knot in the cord or tie it with other

02 Connecting up

sure it is properly disposed of after removal.

cords. The power cords should be routed such that they

Making cable connections. . . . . . . . . . . . . . . . . . .5

The equipment should be disconnected by removing

are not likely to be stepped on. A damaged power cord

About “Bi-wiring” . . . . . . . . . . . . . . . . . . . . . . . . . .5

the mains plug from the wall socket when left unused

can cause a fire or give you an electrical shock. Check

Connecting speaker cables . . . . . . . . . . . . . . . . . .6

for a long period of time (for example, when on

the power cord once in a while. When you find it

Connecting audio cables . . . . . . . . . . . . . . . . . . . .6

vacation).

damaged, ask your nearest PIONEER authorized

Using centralized control with other Pioneer

D3-4-2-2-1a_A1_En

service center or your dealer for a replacement.

components (Except A-10) . . . . . . . . . . . . . . . . . . . 6

S002*_A1_En

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

03 Controls and displays

CAUTION

(A-30 only)

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

The /I STANDBY/ON switch on this unit will not

CAUTION:

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

completely shut off all power from the AC outlet.

HOT SURFACE. DO NOT TOUCH.

Remote control (Except A-10) . . . . . . . . . . . . . . . .9

Since the power cord serves as the main disconnect

The top surface over the internal

04 Operation

device for the unit, you will need to unplug it from the

heatsink may become hot when

AC outlet to shut down all power. Therefore, make

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

operating this product continuously.

Set the power to Standby. . . . . . . . . . . . . . . . . . . .10

sure the unit has been installed so that the power

When using the unit as a power amplifier

cord can be easily unplugged from the AC outlet in

(A-30 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

case of an accident. To avoid fire hazard, the power

Making an audio recording . . . . . . . . . . . . . . . . .11

cord should also be unplugged from the AC outlet

To set for automatic standby status

when left unused for a long period of time (for

(Auto Power Down) . . . . . . . . . . . . . . . . . . . . . . .11

Restoring all the settings to the factory default

example, when on vacation).

D3-4-2-2-2a*_A1_En

settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

05 Additional information

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .12

Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . .12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3

01 Before you start

Chapter 1:

• Do not use any batteries other than the ones

specified. Also, do not use a new battery together

with an old one.

Installing the amplifier

Before you start

• When loading the batteries into the remote control,

When installing this unit, make sure to put it on a level

set them in the proper direction, as indicated by the

and stable surface.

polarity marks ( and ).

• Don’t install it on the following places:

• Do not heat batteries, disassemble them, or throw

2 Insert the new batteries, matching the

– on a color TV (the screen may distort)

them into flames or water.

– near a cassette deck (or close to a device that

What’s in the box

polarities as indicated inside the case.

• Batteries may have different voltages, even if they

gives off a magnetic field). This may interfere with

Please confirm that the following accessories are in the

are the same size and shape. Do not use different

the sound.

box when you open it.

A-30

A-20

types of batteries together.

– in direct sunlight

• To prevent leakage of battery fluid, remove the

• Remote control (Except A-10)

batteries if you do not plan to use the remote

– in damp or wet areas

• AAA/IEC R03 dry cell batteries x2 (Except A-10)

control for a long period of time (1 month or more).

– in extremely hot or cold areas

•Power cord

If the fluid should leak, wipe it carefully off the

– in places where there is vibration or other

• Warranty card

inside of the case, then insert new batteries. If a

movement

battery should leak and the fluid should get on your

– in places that are very dusty

• Operating instructions (This document)

skin, flush it off with large quantities of water.

– in places that have hot fumes or oils (such as a

• When disposing of used batteries, please comply

kitchen)

Note

with governmental regulations or environmental

• Do not mount the unit on a sofa or other object or

public institution’s rules that apply in your country/

material with absorbent qualities, since sound

• Illustrations featured in the Operating Instructions

area.

quality may be adversely affected.

may have been modified or simplified for ease of

explanation, and may therefore differ from the

3 Close the rear lid.

Using the remote control

actual product appearance.

A-30

A-20

The remote has a range of about 7 m at an angle of about

• The illustrations used here are mainly of the A-30.

30º from the remote sensor.

Loading the batteries in the remote

control (Except A-10)

1 Open the rear lid.

A-30

A-20

The batteries included with the unit have been provided

to allow you check product operation and may not last

long. We recommend using alkaline batteries that have

a longer life.

Keep in mind the following when using the remote

WARNING

control:

• Do not use or store batteries in direct sunlight or

• Make sure that there are no obstacles between the

other excessively hot place, such as inside a car or

remote and the remote sensor on the unit.

near a heater. This can cause batteries to leak,

• Remote operation may become unreliable if strong

overheat, explode or catch fire. It can also reduce

sunlight or fluorescent light is shining on the unit’s

the life or performance of batteries.

remote sensor.

• Remote controllers for different devices can

interfere with each other. Avoid using remotes for

Caution

other equipment located close to this unit.

Incorrect use of batteries may result in such hazards as

• Replace the batteries when you notice a fall off in

leakage and bursting. Observe the following

the operating range of the remote.

precautions:

• When inserting the batteries, make sure not to

damage the springs on the battery’s  terminals.

4

En

A30_SYXE8.book 4 ページ ２０１２年２月１６日　木曜日　午前８時５８分

Connecting up 02

English

Chapter 2:

Connecting up

Making cable connections

Caution

• Before making or changing the connections, switch off the power and disconnect the power cord from the AC

outlet.

• Connect the power cord after all the connections between devices have been completed.

DeutschFrançais

Italiano Español Русский

Nederlands

5

En

• During playback, be sure that both the SPEAKERS

Caution

A button and SPEAKERS B button are set to ON

•The SIGNAL GND terminal is provided to reduce

(page 7).

noise when connecting the unit to components

such as an analog turntable.

• Do not connect the PHONO (MM) terminals to any

component other than a turntable; also, do not

connect to a turntable equipped with built-in

equalizer. An excessively high sound output may be

produced, resulting in damage to your speakers or

other devices.

• The unit’s PHONO (MM) terminals are designed to

be used with turntables equipped with MM

(moving-magnet) type cartridges. Turntables

equipped with MC (moving-coil) cartridges cannot

be used.

• Make sure not to bend the cables over the top of

this unit (as shown in the illustration). If this

happens, the magnetic field produced by the

transformers in this unit may cause a humming

noise from the speakers.

• The unit’s POWER AMP DIRECT terminals should

never be connected to any other component’s

connectors except PRE-AMP OUT.

• If your turntable has a grounding wire, secure it to

the ground terminal on this amplifier.

Caution

Note

• When using bi-wiring to connect speakers, avoid

• When connecting a tape cassette deck, playback

adverse affects on the amplifier by being sure to

noise may be heard, depending on the installation

remove the HIGH and LOW short bars provided

location. This noise is caused by leakage flux from

with the speakers. For detailed information, consult

the amplifier’s transformer. In this event, change

the instructions provided with the speakers.

the installation location, or move the deck farther

• When using speakers with removable network

from the amplifier.

circuits, note that if the network is removed, no

• iPod is a trademark of Apple Inc., registered in the

effect will be produced and damage may be caused

U.S. and other countries.

to the speaker.

• Another method of connection is to connect the

SPEAKERS A terminals to HIGH and the

SPEAKERS B terminals to LOW (reverse that shown

About “Bi-wiring”

in the illustration).

This unit can be used with speakers that support bi-

wiring. Be sure to connect the high-frequency and

low-frequency connections correctly.

A30_SYXE8.book 5 ページ ２０１２年２月１６日　木曜日　午前８時５８分

02 Connecting up

Connecting speaker cables

Connecting audio cables

Connect the white plug to the left (L) jack, and the red

1 Twist the cable cores.

plug to the right (R) jack. Be sure to insert the plugs fully

into the jacks.

2 Loosen the nut on the

SPEAKERS

terminal, and insert the speaker cable into

the exposed hole in the terminal shaft.

3 Retighten the terminal nut.

123

Caution

• When using only one set of speaker terminals

(SPEAKERS A or SPEAKERS B), or when utilizing

bi-wiring connections, the speaker used should

have a nominal impedance between 4 Ω and

16 Ω. When using both sets of terminals, the

connected speakers should have nominal

impedance between 8 Ω and 32 Ω. Consult the

instructions accompanying your speakers for

details regarding the impedance value.

• Make sure the positive and negative (+/–) terminals

on the amplifier match those on the speakers.

• These speaker terminals carry HAZARDOUS live

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker

terminal. If any of the bare speaker wire touches the

back panel it may cause the power to cut off as a

safety measure.

6

En

Using centralized control with other

Plugging in

Pioneer components (Except A-10)

Multiple Pioneer components equipped with CONTROL

Important

IN/OUT jacks can be connected to the A-30/A-20 unit,

• When going on a trip or otherwise not using the

allowing centralized control of the components via the

unit for an extended period, always disconnect the

remote sensor on the A-30/A-20. This also allows remote

power cord from its outlet. Note that various

control of components not equipped with a remote

internal settings will not be lost even if the power

sensor, or installed in places where the component’s

cord is disconnected from its outlet for an extended

remote sensor cannot be accessed.

time.

• If it is necessary to detach the power cord, first be

sure to press the 

/I

STANDBY/ON button on the

IN

front panel of the unit so the A-30/A-20 is turned

OFF or the A-10 is in standby mode before

OUT

detaching the cord.

CONTROL

Caution

• The use of a power cord other than the one provided

will invalidate the warranty, since Pioneer will not

be responsible for any damage incurred. (The

power cord provided with the model A-30 has a

rated current capacity of 10 A, while the cord

provided with the A-20/A-10 has a rated current

capacity of 2.5 A.)

• Do not use any power cord other than the one

supplied with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

After you’ve finished making all connections, plug the

unit into an AC outlet.

Note

• For connections use a commercially available

monaural miniplug cord (without resistor).

• When connecting the CONTROL IN/OUT jacks,

commercially available audio cords must also be

used to make analog connections. Merely

connecting the CONTROL IN/OUT jacks alone will

not allow proper system control.

1 Plug the supplied power cord into the

• When a control cord is connected to the A-30/A-

AC IN

socket on the rear panel of the unit.

20’s CONTROL IN jack, the unit cannot be

controlled by pointing the remote control at the A-

2 Plug the other end into an AC outlet.

30/A-20 (the remote sensor is automatically

disabled).

02_connecting_up.fm 6 ページ ２０１２年６月２１日　木曜日　午後２時１分

A30_SYXE8.book 7 ページ ２０１２年２月１６日　木曜日　午前８時５８分

Controls and displays 03

English

Chapter 3:

6 Remote sensor (Except A-10)

13

INPUT SELECTOR

knob/indicators

Receives the signals from the remote control (page 4).

Turn the knob clockwise or counterclockwise so that the

indicator lights for your desired input source. Turning

Controls and displays

7

PHONES

jack

the knob clockwise causes the lit indicator to right.

Use to connect headphones. No sound is produced

Turning counterclockwise causes it to left. When the

when the POWER AMP DIRECT button is ON.

remote control’s MUTE button is pressed to mute the

sound, the indicator for the input source selected with

Front panel

8 DIRECT button/indicator

the INPUT SELECTOR knob flashes.

On : The indicator lights: When this button is set to ON,

1

2 54

3

sound signals are output directly, without being passed

14

POWER AMP DIRECT

button/indicator

A-30

through the various adjustment circuits (BASS, TREBLE,

(A-30 only)

BALANCE, LOUDNESS). This allows reproduction of the

Press this button when the A-30 is to be used as a power

signals with greater fidelity, but it disables any settings

amplifier (page 10).

made with the BASS, TREBLE, BALANCE or LOUDNESS

controls.

Off : The indicator goes off: The signal passes through

DeutschFrançais

the various frequency adjusting circuits. When the

indicator is OFF, adjustments can be made with the

BASS, TREBLE, BALANCE, and LOUDNESS controls.

9

BASS

tone control

Use to adjust the low-frequency tone. The center position

is the flat (normal) position. When turned to the right,

6

7

8

9

10 11 12

13 14

low-frequency tones are emphasized; when turned to the

left, low-frequency tones are de-emphasized.

Italiano Español Русский

1



/I

STANDBY/ON

4

SPEAKERS B

button/indicator

• This button does not operate when the DIRECT

Switches the amplifier between off and on.

Use this button to listen to the speaker system

button is in the on position.

When power is turned on, the power indicator in the

connected to SPEAKERS B terminals.

center of the button will light.

On : The indicator lights. Sound is heard from the

10

TREBLE

tone control

• On the A-10 model, this switches the amplifier

speaker system. (Sound will also be produced from the

Use to adjust the high-frequency tone. The center

between standby and on.

PHONES jack.)

position is the flat (normal) position. When turned to the

Off : The indicator goes off. No sound is heard from the

right, high-frequency tones are emphasized; when

Nederlands

2

STANDBY/APD

indicator

speaker system. Set to this position when listening with

turned to the left, high-frequency tones are de-

When power is set to standby, the indicator lights red.

headphones.

emphasized.

When the Auto Power Down (APD) function is on, the

• This button does not operate when the DIRECT

indicator lights green (page 11).

5

LOUDNESS

button/indicator

button is in the on position.

Use when listening at low volume levels.

3

SPEAKERS A

button/indicator

On : The indicator lights: Boosts low and high

11

BALANCE

control

Use this button to listen to the speaker system

frequencies to give added punch to playback even at a

Should normally be left in the center position. Adjust

connected to SPEAKERS A terminals.

low volume level.

balance if the sound is louder from one of the speakers.

On : The indicator lights. Sound is heard from the

If the right side is louder, turn toward the L (left) position

Off : The indicator goes off: Should normally be left in

speaker system. (Sound will also be produced from the

and if the left side is louder, turn toward the R (right)

this position.

PHONES jack.)

position.

• This button does not operate when the DIRECT

Off : The indicator goes off. No sound is heard from the

• This button does not operate when the DIRECT

button is in the on position.

speaker system. Set to this position when listening with

button is in the on position.

headphones.

• When sound volume is raised, the amount of

change produced by the LOUDNESS circuit is

12 VOLUME control

reduced.

Use to adjust the volume level. (Also allows adjustment

of the headphone sound volume.)

7

En

03 Controls and displays

Rear panel

See pages 5-6 for details regarding connections.

1 GND (Turntable ground) terminal

10

AUX

IN

terminals

This ground terminal is designed to help reduce noise

when a turntable is connected. It is not a safety ground.

11

NETWORK

IN

terminals

2

SPEAKERS A

terminals (Right channel)

12

RECORDER IN/OUT

terminals

3

SPEAKERS B

terminals (Right channel)

13

POWER AMP DIRECT

IN

terminals (A-30

only)

4

SPEAKERS B

terminals (Left channel)

When using the A-30 as a power amplifier, connect the

pre-amplifier here (page 10).

5

SPEAKERS A

terminals (Left channel)

14

CONTROL IN/OUT

jack (Except A-10)

6

AC IN

jack

Connect power cord to here and an AC wall socket.

7

PHONO (MM)

IN

terminals

8

TUNER

IN

terminals

9

SACD/CD

IN

terminals

8

En

A30_SYXE8.book 8 ページ ２０１２年２月１６日　木曜日　午前８時５８分

A30_SYXE8.book 9 ページ ２０１２年３月６日　火曜日　午前１１時１３分

Controls and displays 03

English

1

 STANDBY/ON

Remote control (Except A-10)

Switches the amplifier between standby and on.

2 Input selector buttons

A-30

A-20

Press to select an input source. These select the

component connected to the corresponding input on the

STANDBY/ON DIMMER

rear panel.

1

8

• When the A-30 is connected, the OPTION button is

SACD/CD NETWORK PHONO

1

8

disabled.

TUNER

AUX RECORDER

3 SACD PLAYER control buttons

2

Use to control Pioneer SACD player.

OPTION

5

(Cannot be used to perform playback/pause on the

INPUT

9

2

PD-D6/PD-D6MK2/PD-D9/PD-D9MK2 models.)

SACD PLAYER

FUNC

7

4 NETWORK AUDIO PLAYER control

3

DeutschFrançais

34

10

buttons

NETWORK AUDIO PLAYER

FUNC

Use to control Pioneer network audio player.

3

11

4

5

LOUDNESS

Use to set the loudness circuit ON/OFF (page 7).

LOUDNESS

VOLUME

6

6

MUTE

5

A

10

MUTE

SPEARKERS

Mutes/unmutes the sound.

6

B

11

Italiano Español Русский

7

DIRECT

34

12

Press to access Direct listening (page 7).

12

8

DIMMER

NETWORK AUDIO PLAYER

SOUNDSETUP

This button allows the illumination of the unit's front

panel indicators to be set in three levels (does not affect

4

ENTER

the STANDBY indicator).

34

3

Nederlands

HOME MENU

RETURN

9

INPUT +/–

Use to change the input source. The source changes as

below.

7

DIRECT

APD

13

SACD/CD  NETWORK  PHONO  TUNER 

AUX  RECORDER  Return to the beginning.

10

SPEAKERS A

button/indicator

Use this button to listen to the speaker system

connected to SPEAKERS A terminals.

11

SPEAKERS B

button/indicator

Use this button to listen to the speaker system

connected to SPEAKERS B terminals.

12

VOLUME +/–

Use to set the listening volume.

13

APD

Use to set the Auto Power Down function to ON/OFF

(page 11).

9

En