Pioneer GM-D9601: Connecting the units Connections when using Solderless terminal the speaker input wire connections
Connecting the units Connections when using Solderless terminal the speaker input wire connections: Pioneer GM-D9601
Section
03
Connecting the units
Connections when using
Solderless terminal
the speaker input wire
connections
Connect the car stereo speaker output wires
! Since the wire will become loose over time,
to the amplifier using the supplied speaker
it must be periodically inspected and tigh-
input wire with RCA pin cord.
tened as necessary.
! Do not solder or bind the ends of the
twisted wires.
! Fasten while making sure to not to clamp
the insulating sheath of the wire.
! Use the supplied hexagonal wrench to
tighten and loosen the terminal screw of
the amplifier and use it to securely fasten
the wire. Be careful to avoid excessive tigh-
tening of this screw, which may damage
1 Car Stereo
the wire.
2 Speaker output
3 Red: Right +
Connecting the power terminal
4 Black: Right *
5 Black: Left *
WARNING
6 White: Left +
If the battery wire is not securely fixed to the term-
7 Speaker input wire with RCA pin cord
inal using the terminal screws, there is a risk of
To the RCA input jack of this unit
overheating, malfunction and injury, including
minor burns.
Notes
! If speaker wires with an RCA pin cord from a
! Always use the recommended battery and
headunit are connected to this amplifier, the
ground wire, which is sold separately. Con-
amplifier will automatically turn on when the
nect the battery wire directly to the car bat-
headunit is turned on. When the headunit is
tery positive (+) terminal and the ground
turned off, the amplifier turns off automati-
wire to the car body.
cally. This function may not work with some
! Recommended wires size (AWG: American
headunits. In such cases, please use a sys-
Wire Gauge) is as follows. The battery wire,
tem remote control wire (sold separately). If
the ground wire and the optional direct
multiple amplifiers are to be connected to-
ground wire must be same size.
gether synchronously, connect the head unit
! Use a wire of 8 AWG to 16 AWG wire for the
and all amplifiers via the system remote con-
speaker wire.
trol wire.
! Connect the system remote control wire when
Battery wire and ground wire size
you wish to only turn on the car stereo, not the
amplifier.
Wire length Wire size
! This amplifier automatically selects an input
less than 3.6 m 6 AWG
signal mode between the RCA level and the
less than 6.4 m 4 AWG
speaker level by detecting an input signal.
8
En
Оглавление
- Before you start
- Setting the unit
- Connecting the units
- Connecting the units Connections when using Solderless terminal the speaker input wire connections
- Connecting the units
- Installation Before installing the amplifier Attaching the Bass boost remote control
- Installation
- Additional information
- Avant de commencer
- Réglage de l’appareil
- Connexion des appareils
- Installation
- Informations complémentaires
- Prima di iniziare
- Impostazione dell’unità
- Collegamento delle unità
- Installazione
- Informazioni supplementari
- Antes de comenzar
- Configuración de la unidad
- Conexión de las unidades
- Instalación
- Información adicional
- Bevor Sie beginnen
- Einstellen des Geräts
- Anschließen der Geräte
- Installation
- Zusätzliche Informationen
- Vóór u begint
- Het toestel installeren
- De toestellen aansluiten
- De toestellen aansluiten Aansluiting via de luidspre- Aansluitingen niet solderen keringangskabel
- De toestellen aansluiten
- Installatie
- Aanvullende informatie
- Перед началом эксплуатации
- Настройка усилителя
- Подключение устройств
- Установка
- Установка Пример установки усилителя на напольном коврике или шасси
- Дополнительная информация