Vitek VT-1262 PK: ENGLISH
ENGLISH: Vitek VT-1262 PK
6
ENGLISH
experimentally (always start with the lowest
STEAM IRONING
temperature and raise it gradually until you get
While steam ironing it is necessary to set the iron-
the desired result).
ing temperature “•••” or “MAX”.
•
Corduroy and other fabrics that become glossy
The iron is provided with an anti-drip valve that
quickly should be ironed strictly in one direc-
stops water supply if the iron soleplate tempera-
tion (in the direction of the pile) with slight
ture is too low; it prevents dripping from the iron
pressure.
soleplate openings (14). During heating and cool-
•
To avoid appearance of glossy spots on syn-
ing of the iron soleplate, you will hear character-
thetic and silk fabrics, iron them backside.
istic clicks of the anti-drip valve opening/closing,
which indicates its normal operation.
SETTING THE IRONING TEMPERATURE
•
Place the iron on its base (9).
•
Place the iron on its base (9).
•
Set the continuous steam supply knob (3) to
•
Insert the power plug into the mains socket.
the position
(the steam supply is off).
•
Turn the knob (11) to set the required iron-
•
Insert the power plug into the mains socket.
ing temperature: “•”, “••”, “•••” or “MAX”
•
Make sure that there is enough water in the
(depending on the type of fabric), the pilot
water tank (10).
lamp (8) will light up.
•
Turn the knob (11) to set the required ironing
•
Once the temperature of the soleplate (14)
temperature: “•••” or “MAX”, the pilot lamp
reaches the set point, the pilot lamp (8) will go
(8) will light up.
out and you can start ironing.
•
Once the soleplate (14) reaches the set tem-
Note:
perature, the pilot lamp (8) will go out and you
If you are ironing at high temperature but you
can start ironing.
need to switch to low temperature, wait until the
•
Turn the continuous steam supply knob (3)
soleplate temperature decreases and the pilot
to set the steam generation rate, steam will
lamp(8) lights up, and only then you may start
start going out from the soleplate (14) open-
ironing. While steam ironing it is necessary to
ings.
set the ironing temperature “•••” or “MAX”.
•
After you finish ironing, set the temperature
The steam ironing sector is marked with corre-
control knob (11) to the “MIN” position, and the
sponding symbols on the temperature control
continuous steam supply knob (3) to the posi-
knob (11).
tion
(steam supply is off).
•
Pull the power plug out of the mains socket and
WATER SPRAY
let the iron cool down completely.
•
You can dampen the fabric by pressing the
•
Open the water inlet lid (2), turn over the iron
water spray button (5) several times.
and drain any remaining water.
•
Make sure that there is enough water in the
ATTENTION!
water tank (10).
If steam is not supplied constantly during the
operation, check whether the temperature control
DRY IRONING
knob (11) and the continuous steam supply knob
•
Place the iron on its base (9).
(3) are set properly and whether there is water in
•
Insert the power plug into the mains socket.
the water tank (10).
•
Set the continuous steam supply knob (3) to
the position
(the steam supply is off).
BURST OF STEAM
•
Turn the knob (11) to set the required iron-
The burst of steam function is useful for ironing
ing temperature: “•”, “••”, “•••” or “MAX”
folds and can only be used at high ironing tem-
(depending on the type of fabric), the pilot
peratures (when the iron temperature control knob
lamp (8) will light up.
(11) is set to the position “•••” or “MAX”).
•
Once the soleplate (14) reaches the set tem-
•
When pressing the burst of steam button (4)
perature, the pilot lamp (8) will go out and you
steam will go out of the iron soleplate more
can start ironing.
intensively.
•
After you finish ironing, set the temperature
Note:
control knob (11) to the “MIN” position.
To avoid water leakage from steam openings,
•
Pull the power plug out of the mains socket and
press the burst of steam button (4) with a 4-5 sec.
let the iron cool down completely.
interval.
IM VT-1262.indd 6 10.06.2016 11:47:56