AEG 413605 MFE 1500: 20 21 ENGLISH

Protect cutting discs against shock, impact and harmful

If needed, an exploded view of the tool can be ordered.

environmental factors.

Please state the machine type printed as well as the six-digit

No. on the label and order the drawing at your local service

MAINS CONNECTION

agents or directly at: Techtronic Industries GmbH,

Max-Eyth-Straße 10, 71364 Winnenden, Germany.

Connect only to single-phase a.c. current and only to the

system voltage indicated on the rating plate. It is also

SYMBOLS

possible to connect to sockets without an earthing contact

as the design conforms to safety class II.

CAUTION! WARNING! DANGER!

SPECIFIED CONDITIONS OF USE

The wall-chaser machine cuts slots for cables and pipes

(masonry grooves) in any kind of brickwork with two

diamond cutting discs running parallel to each other.

Always disconnect the plug from the socket

before carrying out any work on the machine.

Do not use this product in any other way as stated for

normal use.

Appliances used at many different locations including wet

Please read the instructions carefully before

room and open air must be connected via a residual current

starting the machine.

device (FI, RCD, PRCD) of 30mA or less.

EC-DECLARATION OF CONFORMITY

Always wear goggles when using the

We declare under our sole responsibility that the product

machine.

described under “Technical Data” fulfi lls all the relevant

regulations and the directives 2011/65/EU (RoHs),

2006/42/EC, 2004/108/EC and the following harmonized

standards have been used:

Wear ear protectors!

EN 60745-1:2009 + A11:2010

EN 60745-2-22:2011 + A11:2013

EN 55014-1:2006 + A 1:2009 + A2:2011

EN 55014-2:1997 + A1:2001 + A2:2008

Use an FFP2 particulate respirator as the

EN 61000-3-2:2006 + A1:2009 + A2:2009

minimum amount of protection.

EN 61000-3-3:2008

EN 50581:2012

Wear gloves!

Winnenden, 2014-08-11

Accessory - Not included in standard

Alexander Krug

equipment, available as an accessory.

Managing Director

Authorized to compile the technical fi le.

Techtronic Industries GmbH

Do not dispose of electric tools together with

Max-Eyth-Straße 10

household waste material.

71364 Winnenden

Electric tools and electronic equipment that

Germany

have reached the end of their life must be

collected separately and returned to an

ADVICE FOR OPERATION

environmentally compatible recycling facility.

The speed of rotation is adjusted electronically when the

Check with your local authority or retailer for

load increases.

recycling advice and collection point.

In case of a longer overload period the speed is decreased

Class II tool, tool in which protection against

electronically. The machine continues to run slowly to cool

electric shock does not rely on basic

down the motor coil. After switching off and on the machine

insulation only, but in which additional safety

can be used at rated load.

precautions, such as double insulation or

Under the effect of extreme electromagnetic interferences

reinforced insulation, are provided.

from the outside, temporary variations in the speed of

There being no provision for protective

rotation could arise in particular cases.

earthing or reliance upon installation

conditions.

Sharpen blunt diamond cutting blades (can be recognised

by sparks fl ying while cutting) by making several cuts into

European Conformity Mark

calcareous sandstone or a special sharpening stone.

The cutting discs get very hot when in use. Do not touch

them before they have cooled down.

Regulatory Compliance Mark (RCM). Product

meets applicable regulatory requirements.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all

times.

EurAsian Conformity Mark.

Use only AEG accessories and spare parts. Should

components need to be exchanged which have not been

described, please contact one of our AEG service agents

(see our list of guarantee/service addresses).

20 21

ENGLISH