Pioneer DJM-700: TROUBLESHOOTING

01_DJM-700_En.book 25 ページ ２００７年７月１０日　火曜日　午後８時４１分

TROUBLESHOOTING

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check

the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in

use.

English

If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.

Symptom Possible Cause Remedy

No power • The power cord has not been connected. • Connect to power outlet.

No sound, or sound volume is

• Input selector is set incorrectly.

• Set input selector to playback component.

too low.

• Connection cables are connected incorrectly, or

• Connect correctly.

connections are loose.

• Jacks or plugs are dirty.

• Clean soiled jacks/plugs before connecting.

• The rear panel master output attenuator switch

• Adjust rear panel master attenuator switch

(

MASTER ATT

) is set to –6 dB, etc.

(

MASTER ATT

).

No digital output. • The digital output sampling frequency (fs) does

• Set rear panel sampling frequency selector to

not match the specifications of the connected

match the specifications of the connected

component.

component.

Sound is distorted. • Master output level is too high.

• Adjust master output level (

MASTER LEVEL

)

dial or the rear panel master output attenuator

(

MASTER ATT

) switch.

• Input level is too high.

• Adjust the

TRIM

dial so that the input level

approaches 0 dB on the channel level indicator.

Cross fader doesn’t work. •

CROSS FADER ASSIGN

switch setting ([

A

],

• Correctly set the

CROSS FADER ASSIGN

switch

[

THRU

], [

B

]) is incorrect.

for the desired channel.

Can’t perform fader start with

• The

FADER START

button is set to OFF.

• Set the

FADER START

button to ON.

CD player.

• Rear panel

CONTROL

jack is not connected to

• Use a control cable to connect the

CONTROL

CD player.

jacks of mixer and CD player.

• Only the rear panel

CONTROL

jack is connected

• Connect both the

CONTROL

jacks and analog

to the CD player.

input connectors.

Effects don’t work. • Effect channel selecter setting is incorrect.

• Correctly select the channel on which you wish

to apply effects.

• Effect parameter 2 adjust dial (

LEVEL/DEPTH

) is

• Adjust the effect parameter 2 adjust dial

set to [

MIN

].

(

LEVEL/DEPTH

).

External effector doesn’t work. • Effect selecter is not set to [

SND/RTN

].

• Set effect selector to [

SND/RTN

].

• Effector is not connected to rear panel

SEND/

• Connect effector to the rear panel

SEND/

RETURN

connector.

RETURN

connectors.

• Effect channel selector is set to incorrectly.

• Use the effect channel selector to select the

audio source to which you wish to apply the

effects.

Sound from external effector is

• Input level from external effector is set too high. • Lower the output level of the external effector.

distorted.

BPM can’t be measured.

• Input level is too high, or too low.

• Adjust the

TRIM

dial so that the input level

Measured BPM value is

approaches 0 dB in the channel level indicator.

incorrect.

• Adjust other channels as well so that the input

levels approach 0 dB in the channel level

indicator.

• BPM may not be correctly measurable with

• Strike the

TAP

button to set BPM manually.

some tracks.

The measured BPM value is

• Some differences may occur due to differences

• No remedy is necessary.

different from the value

in BPM detection methods.

published with the CD.

MIDI sequencer can’t be

• MIDI sequencer’s synch mode is not set to

• Set MIDI sequencer’s sync mode to “slave”.

synchronized.

“slave”.

• MIDI sequencer is not supported type.

• MIDI sequencers that do not support MIDI

timing clock cannot be synchronized.

Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then

on again.

25

En