Vitek VT-1235: ENGLISH
ENGLISH: Vitek VT-1235
ENGLISH
CHOICE OF WATER
Determination of Fabric type/tempera-
• To fill the water tank use regular tap wa-
ture
ter. If the water is hard then it is recom-
Synthetics, nylon, acryl, polyester
•
mended to mix it with distilled water at a
(low temperature)
ratio of 1:1, if the water is very hard, mix it
••
Silk/wool (medium temperature)
with distilled water at a ratio of 1:2 or use
•••
Cotton/linen (high temperature)
only distilled water.
• This table is only for smooth materials.
Note:
Fabrics of other types (crimped, raised
Do not fill the water tank (10) with
etc.) are best ironed at low temperature.
scented liquids, vinegar, starch solu-
• First sort items by ironing temperature:
tions, descaling reagents, chemical
wool with wool, cotton with cotton etc.
substances etc.
• The iron heats up faster than it cools
down. For this reason it is recommended
FILLING THE WATER TANK
to begin ironing at low temperature (for
Make sure that the iron is disconnected
instance synthetic fabrics). After that,
from electrical power before filling it with
move to higher temperature ironing.
water.
Cotton and linen should be ironed after
• Set the steam release regulator (3) to the
all the others.
position of steam vapor OFF.
• If an item is made from a mix of fabrics,
• Open the water tank lid (2).
then the iron should be set for the fabric
• Fill the water tank with water (10). Close
with the lowest ironing to (for instance if
the lid (2).
an item is made from 60% polyester and
40% cotton, it should be ironed at the
Note:
temperature used for ironing polyester
• Do not fill it with water above MAX. in-
“•”).
dication.
• If you cannot define the fabric the item is
• If you need to refill the water tank dur-
made from, find a place on it that is hid-
ing ironing, turn off the iron and un-
den while wearing and, on practice select
plug the power cord from the outlet.
the ironing temperature (always start at
• After you finish ironing, open the wa-
the lowest and gradually raise it until you
ter tank lid (2) and pour out the re-
get the desired result.)
maining water.
• Corduroy and other fabrics that start
glossy quickly should be ironed strictly in
IRONING TEMPERATURE
one direction (along the lines) with slight
Before ironing test the heated iron on the
pressure.
old cloth to be sure that the iron soleplate
• To avoid appearance of glossy spots on
(13) and the water tank (10) are clean.
the synthetic and silk fabrics, iron them
• Always check the recommended iron
back-side.
temperature indicated on the tag before
ironing.
SETTING THE IRONING TEMPERATURE
• If the tag does not list the recommended
• Place the iron on the base (8).
ironing temperature, but you know the
• Insert the power plug into the outlet.
type of fabric, then use the following
• Set the temperature regulator (11) to the
table to determine the proper tempera-
required ironing temperature: “•”, “••”,
ture.
“•••” or “max” (depending on the type
5
VT-1235.indd 5VT-1235.indd 5 22.07.2009 17:35:2522.07.2009 17:35:25
Оглавление
- ENGLISH
- ENGLISH
- ENGLISH
- ENGLISH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- DEUTSCH
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- РУССКИЙ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- ҚАЗАҚ
- POLSKI
- POLSKI
- POLSKI
- POLSKI
- ČESKÝ
- ČESKÝ
- ČESKÝ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- УКРАЇНЬСКИЙ
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- БЕЛАРУСКI
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК
- ЎЗБЕК