Vitek VT-1253: ENGLISH
ENGLISH: Vitek VT-1253
ENGLISH
move the protective cartoon covering (if
perature indicated on the tag before iron-
any) from the iron sole (12).
ing.
• Make sure that the electrical supply voltage
• If the tag does not list the recommended
corresponds to the iron’s operating volt-
ironing temperature, but you know the type
age.
of fabric, then use the following table to de-
termine the proper temperature.
Note:
- When using the unit for the first time,
Signs Fabric type/temperature
the heating element of the unit burns
Synthetics, nylon, acryl, polyester
•
(low temperature)
that is why some smoke or foreign odor
•• Silk/wool (medium temperature)
can appear. It is normal.
••• Cotton/flax (high temperature)
CHOICE OF WATER
• This table is only for smooth materials.
To fill the water tank use regular tap water. If
Fabrics of other types (crimped, raised
water is hard then it is recommended to mix it
etc.) are best ironed at low temperature.
with distilled water at a ratio of 1:1, if water is
• First sort items by ironing temperature:
very hard, mix it with distilled water at a ratio
wool with wool, cotton with cotton etc.
of 1:2 or use only distilled water.
• The iron heats up faster than is cools down.
For this reason it is recommended to begin
Note:
ironing at low temperature (for instance
- Do not fill the water tank (11) with
synthetic fabrics).
scented liquids, vinegar, starch solu-
• After that, move to higher temperature
tions, descaling reagents, chemical
ironing. Cotton and linens should be ironed
substances etc.
last.
• If an item is made from a mix of fabrics, then
FILLING THE WATER TANK (pic. 1, 2)
the iron should be set for the fabric with the
Make sure that the iron is disconnected from
lowest ironing (for instance if an item is
electrical power before filling it with water.
made from 60% polyester and 40% cotton,
Set the steam release regulator (3) to the Off
it should be ironed at the temperature used
position.
for ironing polyester “•”).
• Open the water tank lid (2).
• If you cannot define the fabric the item is
• Fill it with water using the water bowl (14).
made from, find a place on it that is hid-
Close the lid (2).
den while wearing and, on practice select
the ironing temperature (always start at the
Note:
lowest and gradually raise it until you get
- Do not fill it with water above the MAX.
the desired result.)
mark.
• Corduroy and other fabrics that start glossy
- If you need to refill the water tank dur-
quickly should be ironed strictly in one di-
ing ironing, turn off the iron and unplug
rection (along the lines) with slight pres-
the power cord from the outlet.
sure.
- After you finish ironing, open the water
• To avoid appearance of glossy spots on the
tank lid (2) and drain the remaining wa-
synthetic and silk fabrics, iron them back-
ter (pic.8).
side.
IRONING TEMPERATURE
SETTING THE IRONING TEMPERATURE
Before operating test the heated iron on the
• Place the iron on the base (8).
old cloth to be sure that the iron sole (12) and
• Insert the power plug into the outlet.
the water tank (11) are clean.
• Set the temperature regulator (10) to the re-
• Always check the recommended iron tem-
quired ironing temperature: “•”, “••”, “•••”
5
1253.indd 51253.indd 5 27.05.2010 10:58:5127.05.2010 10:58:51
Оглавление
Топ 10 инструкций
100.00
Gefest 6100-0399.85
Gefest 6100-04 000199.85
Alcatel Pixi 499.75
Casio EX-H20G Silver99.72
Tp-Link TL-WA5210G99.72
Gefest 310299.67
Casio CTK-400099.64
Gefest 6100-0299.63
Casio EX-Z1050 Silver