AEG KRC 4361 BT: English

English

35

• Fortheinstallationthecupboardmustfullthefollowing

Power supply

conditions:

Please ensure that the mains voltage corresponds to the

Thickness of the cupboard floor

information on the type plate. Plug the power plug into a

between 16 mm and 20 mm.

properly installed socket.

• Thewallmountingofthecupboardmustbestableand

Inserting the power reserve battery

anchored firmly in the wall with at least 2 screws.

(Battery not included in scope of delivery)

• Important! Do not install the device above a cooker!

During a power outage, or when the power plug is pulled

• Wheninstallingthedeviceitmustbeensuredthatthere

from the socket, the clock time and the alarm times will be

is a power socket within reach.

lost. To prevent this, insert a power reserve battery as follows.

• Themainssocketmustbewithineasyreach,sothatthe

plug can be quickly removed in an emergency.

1. Open the battery compartment on the bottom. Turn the

• Important! Do not connect the device to the mains

battery compartment lid in the direction “OPEN”.

power supply until after installation!

2. Insert a button cell battery of the type CR 2025 3 V. Ensure

• Thedevicecannotbeinstalledundercupboardsunder

the correct polarity (see battery compartment lid)!

which there is a lighting strip.

3. Close the battery compartment again.

• Formounting,youmayneedthefollowingsupplies:A

WARNING:

drill with 6 mm drill bit, pilot drill or nail, Allen key, tape

Thebatteriesshallnotbeexposedtoexcessiveheatsuch

measure, adhesive tape, scissors, safety goggles.

as sunshine, fire or the like. Danger of explosion!

Supplied mounting accessories

CAUTION:

4 Screws

• Batteriesmayleakoutandlosebatteryacid.Ifthe

4 Spacers

device is not used for a longer period of time, remove

1 Drilling template

the battery.

• Batteriesdonotbelonginthehouseholdwaste.

CAUTION:

Dispose of spent batteries at the designated collection

• Pleaseadheretothedimensionsstatedintheinstalla-

points or at the dealer.

tion instructions.

• Youshoulduseonlytheinstallationaccessoriessup-

plied.

Switching the Device on/off (10)

• Turnonthedevicebypressingthe

/FUNC button.

Installation

• Toturnoffthedevice,keepthe /FUNC button pressed

for about 3 seconds.

1. Tape the template firmly down to the shelf with adhesive

tape. With the help of a gimlet or nail pierce the crosses

NOTE:

at the attachment points and use it to mark the holes.

After about 30 minutes without signal, or if the signal is too

2. Remove the template and drill the holes into the wall

low, the device will switch to Standby automatically.

cupboard.

3. Insert the spacer into the holes provided on the device.

Selecting the operating mode (10)

NOTE:

When the device is turned off, you can switch between

Sufficient ventilation is only guaranteed with a spacer.

radio and Bluetooth mode by pressing the

/FUNC. button

4. Countersink the screws into the holes in the cupboard.

repeatedly.

5. Using the 4 screws and the spacers, attach the kitchen

radio to the bottom of the cupboard.

Setting of the Clock (24 h)

6. Tighten the screws hand-tight with an Allen wrench.

1. Hold down the TIME SET/COOK TIMER button (14) for

approx.3seconds.Thenotication“24H”willappearin

CAUTION:

the display.

Use an Allen wrench and not an electric screwdriver.

2. Select the time format with the SKIP+/SKIP- buttons (7/8).

NOTE:

Start-up of the device / Introduction

“PM” will show in the display in the afternoon with the

12-hour indication.

• Makesurethatthedeviceisadequatelyventilated!

• Ifapplicable,removetheprotectivelmfromthedisplay.

3. Press the TIME SET/COOK TIMER button to confirm.

The hour setting will blink in the display.

4. Adjust the setting with the SKIP+/SKIP- buttons (7/8).