AEG KRC 4355 CD: English

English

37

• Readtheoperatinginstructionsthoroughlybeforethe

2. You may now select the settings for the hours, minutes,

start-up!

and the display format (24H or 12H) one by one.

• Ifapplicable,removetheprotectivelmfromthedisplay.

NOTE:

“PM” will show for afternoons in the 12 hour display.

Inserting the power reserve batteries

(Batteries not included)

Volume adjusting

In case of a power failure or if the power plug of the device

The desired volume can be sent using the VOLUME regula-

is disconnected from the outlet, then the settings will be

tor (1). To adjust the volume with the remote control, press

retained if the power reserve batteries have been inserted.

the

/ buttons (33).

1. Open the battery compartment on the bottom.

2. Insert 2 AAA/R03 1.5 V type batteries. Pay attention to the

Listening to the radio

correct polarity (see bottom of battery compartment)!

3. Close the battery compartment again.

NOTE:

4. If the device is not used for a long period of time, then

remove the batteries from the device to prevent the

The preset stations will be lost if the power is interrupted.

battery acid from leaking.

Scanning stations

WARNING:

Thebatteriesshallnotbeexposedtoexcessiveheatsuch

• TuneintothedesiredstationwiththeTUNINGcontrol(11).

as sunshine, fire or the like. Danger of explosion!

The display will show the respective frequency.

• Ifthereisinterferenceonthereceivedstation,tryto

CAUTION:

improve the reception by rotating, winding or unwinding

• Differentbatterytypesornewandusedbatteriesmay

the wire antenna.

not be used together.

• Batteriesdonotbelonginthehouseholdwaste.

Presetting radio stations

Dispose of spent batteries at the designated collection

The device can preset up to 20 radio stations. To preset a

points or at the dealer.

station, follow the steps below:

1. Search for a station as described in “Scanning stations”.

Power supply

2. Press the MEM/PROG button (4/21). The storage space

• Inserttheplugintoaproperlyinstalled230V,50Hzpower

willstarttoashonthedisplay.

socket. Please ensure that the mains voltage corresponds

3. Use the M

(18/32) and M (19/31) buttons to choose

to the information on the type plate.

the preset location for the corresponding station.

• Ifyouhavenotinsertedanypowerreservebatteries,the

4. Press the MEM/PROG button again. The station will be

preset time and radio stations are lost as soon as the

preset. The frequency of the preset radio station will be

power supply has been interrupted.

displayed.

Switching the Device on/off (12/35)

Recalling preset radio stations

Switch the device to the standby mode with the STANDBY/

1. Choose the preset location with the M

(18/32) and M

AL.OFF (

) button (the time is displayed). If this button is

(19/31) buttons.

pressed once more, the device switches on again.

Automatic station scan

NOTE: In CD mode

When holding down the MEM/PROG button (4/21) for ap-

To keep the power consumption to a minimum, the device

prox.3seconds,thedevicewillstarttheautomaticstation

has an automatic switch-off. If the device is in stop mode,

scan searching the entire frequency range automatically for

forexampleaftertheplaybackofaCDhasbeenstopped,

stations. The stations found will be stored on the preset loca-

the device will automatically shut off after about 11 minutes.

tions 1- 20 in ascending order.

NOTE:

Setting of the Clock (in Standby Mode)

• Thescanwillonlystopafterall20presetlocationshave

• Youmustselectthesettingswiththe

REW/F.FWD

been filled.

buttons (6/7), or with the

/

/

/

buttons (33).

• Theordercannotbechangedonceset.

• AlwaysconrmyoursettingswiththeTIMESETbutton

(16/30).

1. KeeptheTIMESETpresseddownforapprox.3seconds.

Theseconddisplaywillstarttoash.