AEG SB2E850R: English English

SPECIFIED CONDITIONS OF USE

WARNING! Read all safety warnings and all instruc-

tions. Failure to follow the warnings and instructions may result in

The electronic percussion drill/screwdriver can be universally used

electric shock, re and/or serious injury.

for drilling, percussion drilling, screwdriving and cutting screw

Save all warnings and instructions for future reference.

threads.

DRILL SAFETY WARNINGS

ECDECLARATION OF CONFORMITY

Wear ear protectors when impact drilling. Exposure to noise

We declare under our sole responsibility that the product described

can cause hearing loss.

under “Technical Data” fullls all the relevant provisions of the

directives:

Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

2011/65/EU (RoHS)

2014/30/EU

Hold power tool by insulated gripping surfaces, when

2006/42/EC

performing an operation where the cutting accessory may

and the following harmonized standards have been used.

contact hidden wiring or its own cord. Cutting accessory con-

tacting a “live” wire may make exposed metal parts of the power

EN 60745-1:2009 + A11:2010

tool “live” and could give the operator an electric shock.

EN 60745-2-1:2010

EN 60745-2-2:2010

SCREWDRIVER SAFETY WARNINGS

EN 55014-1:2006 + A1:2009 + A2:2011

EN 55014-2:1997 + A1:2001 + A2:2008

Hold power tool by insulated gripping surfaces, when

EN 61000-3-2:2014

GB

performing an operation where the fastener may contact

EN 61000-3-3:2013

hidden wiring or its own cord. Fasteners contacting a “live”

EN 50581:2012

wire may make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

Additional Safety and Working Instructions

Winnenden, 2016-03-25

Use protective equipment. Always wear safety glasses when

working with the machine. The use of protective clothing is re-

commended, such as dust mask, protective gloves, sturdy non-slip

footwear, helmet and ear defenders.

Keep mains lead clear from working range of the machine. Always

Alexander Krug / Managing Director

lead the cable away behind you.

Authorized to compile the technical le

Do not machine any materials that present a danger to health (e.g.

asbestos).

Techtronic Industries GmbH

When working in walls ceiling, or oor, take care to avoid electric

Max-Eyth-Straße 10, 71364 Winnenden, Germany

cables and gas or waterpipes.

Clamp your workpiece with a clamping device. Unclamped workpi-

MAINS CONNECTION

eces can cause severe injury and damage.

Appliances used at many dierent locations including wet room

Switch the device o immediately if the insertion tool stalls! Do

and open air must be connected via a residual current device (FI,

not switch the device on again while the insertion tool is stalled,

RCD, PRCD) of 30mA or less.

as doing so could trigger a sudden recoil with a high reactive force.

Connect only to single-phase AC system voltage as indicated on

Determine why the insertion tool stalled and rectify this, paying

the rating plate. It is also possible to connect to sockets without an

heed to the safety instructions.

earthing contact as the design conforms to safety class II.

Possible causes can be:

Only plug-in when machine is switched o.

• it is tilted in the workpiece to be machined

• breakage of the material to be used

MAINTENANCE

• the power tool is overloaded

The ventilation slots of the machine must be kept clear at all times.

Do not reach into the machine while it is running.

If the machine is mainly used for percussion drilling, regularly

The insertion tool may become hot during use.

remove collected dust from the chuck. To remove the dust hold the

WARNING! Danger of burns

machine with the chuck facing down vertically, and completely

• when changing tools

open and close the chuck. The collected dust will fall from the

• when setting the device down

chuck. It is recommended to regularly use cleaner for the clamping

Chips and splinters must not be removed while the machine is

jaws and the clamping jaw borings.

running.

If the supply cord of this appliance is damaged, it must only be

Always disconnect the plug from the socket before carrying out any

replaced by a repair shop appointed by the manufacturer, to avoid

work on the machine.

hazardous situations.

Use only AEG accessories and spare parts. Should components

need to be replaced which have not been described, please contact

one of our AEG service agents (see our list of guarantee/service

addresses).

English

English

14