AEG MRC 4121: English

69

English

Inserting the Battery (Backup)

(Battery is not included with the device)

In case of a power cut or if the device is unplugged, with backup battery inserted, the set-

tings will be kept.

1. Open the battery compartment at the bottom. Remove for this the screw of the bat-

tery compartment lid with a Phillips screwdriver.

2. Insert one battery of the type CR2032, 3 V. Mind the correct polarity (

must be at the

top)!

3. Close the battery case. Secure the battery compartment lid again with the screw.

4. Ifthedeviceisnotusedforanextendedperiodoftime,removetheBatteryfromthe

device to avoid any leaking of battery acid.

CAUTION:

Batteries are not to be disposed of together with domestic wastes. Dispose of the used

batteries at the relevant collection bin or at your dealer’s.

WARNING:

Donotexposethebatteriestohightemperaturesordirectsunlight.Neverthrowbatter-

ies into the fire. There is a danger of explosion!

Power supply

• Insertthegridplugintoaproperlyinstalledthreeprongsocket.

• Makesurethegridvoltagecorrespondstotheguresontheratingplate.

• Ifyouhavenotinsertedabackupbattery,thestoredclocktimewillbelostassoonas

the power supply is interrupted.

Switching the Unit On/Off

Press the

button (9) to switch the unit on or off.

Volume

Adjust the volume with the

/ DISPLAY button (8) and / SENSOR BEEP (10).

Display Brightness

Use the SNOOZE/SLEEP / DIMMER button (4) to adjust the display brightness.

Turn off display light

If you are disturbed by even the lowest brightness setting of the light, you can turn it off.

70

English

• Instandby,keeptheMEM.SET/NAP/MEM+button(1)pressedforapprox.3seconds.

Apointnextto (16)lightsup.Thedisplaylightturnsoffafterapprox.15seconds.

NOTE:

Press any button to switch on the brightness again for 15 seconds.

• Switch on the display light: To switch on the display light again permanently, press

anybuttonbriey.ThenkeepMEM.SET/NAP/MEM+button(1)pressedforapprox.

3seconds.Thepointnextto

(16) disappears.

Toggling the display

The following can be shown alternatingly on the display:

Time

Year Date Temperature

1. In order to activate this function, use the

button (9) to switch the device to standby.

2. Keep the / DISPLAY button (8) pressed, until “ ” appears briefly on the display.

Switch off toggling: To switch off Auto Toggle, keep the

/ DISPLAY button pressed

again in standby. “ ” appears briefly on the display.

NOTE:

Only the time is shown via the rotatable projector (20).

Temperature display

There are two options for displaying the current room temperature:

• BrieypresstheCLK.ADJ/TEMPbutton(5).

• PassyourhandovertheInfraredsensorsatadistanceof10cm(21).

Toggle temperature display between °C (Celsius) and °F (Fahrenheit)

Press the / DST/C-F button (7) whilst the temperature is displayed.

Display after using the infrared sensors

The following indicators are shown on the display if you pass your hand repeatedly over

the infrared sensors in standby.

Temperature

Alarm time AL1 Alarm time AL2 Time

The following indicators are shown on the display if you pass your hand repeatedly over

the infrared sensors when the device is in operation.

Radio frequency

Temperature Alarm time AL1 Alarm time AL2 Time

71

English

NOTE:

Toexecutethefunction,thedistancebetweenyourhandandthesensorsshouldbe

max.10cm.

Turn the beep off/on when using the infrared sensors

A beep sounds when you pass your hand over the infrared sensors. If you want to turn off

the beep, proceed as follows:

1. Switch the device to standby using the

button (9).

2. Keep the /SENSOR BEEP button (10) pressed until “ ” is shown briefly on the

display.

Turn the beep on again: To switch the beep on again, keep the

/SENSOR BEEP button

pressed again. “ ” briefly appears on the display.

Restore Factory Defaults

Any malfunctions during operation can be rectified by pressing the Reset button.

• Pushthe(13)buttonwiththehelpofawireorasimilaritemtoresettheelectronics.

Setting the Clock

1. Use the button (9) to switch the device to standby.

2. Hold the CLK.ADJ / TEMP button (5) depressed until the year indication on the display

flashes.

• Nowyoucansettheyear,themonth,theday,thetimedisplayformat(12Hr/24Hr),

the hours, and the minutes with the buttons / DST/C-F (7) and / Y-M-D (6).

• Ineachcase,conrmtheinputwiththeCLK.ADJ/TEMPbutton.Thecurrent

indication to be set flashes on the display.

NOTE:

• Theinputisstoredautomaticallywithinapproximately30secondswhennobuttonis

pressed.

• Ifthetimeisdisplayedin12hourformat,thepointnexttoPMlightsup(18):

PM=Afternoon

• Settingoftheweekdayisdoneautomatically.Fortechnicalreasons,theweekday

cannot be shown on the display.