AEG bss 4815: English

English

36

13  TREBLE+/TREBLE- buttons (adjust trebles)

  BASS+/BASS buttons (adjust basses) 

14   button (On/Operational readiness)

Wall mounting

A  Threaded bolt (2x)

B  Mounting plate (2x)

C  Countersunk screw (4x)

D  Dowel (4x)

First Use of the Device/Introduction

•  Select a proper place for the device. A dry, level and slip

proof surface is suitable.

•  Make sure the device is vented sufficiently!

•  Remove the protective film from the device, if present.

Wall mounting (Sound bar)

You can also mount the device to the wall.

 CAUTION: 

Make sure beforehand whether there are cables in the wall 

which could be damaged!

 NOTE: Check the reach of the cable!

To mount the device, make sure that an easily accessible 

plug outlet is available within reach of the power cable.

The distance between the mountings for wall mounting is 

618 mm.

•  Hold the mounting plate (B) to the wall so that the above-

listed distance is kept horizontally and from the center of 

the mounting plates.

•  Mark the four positions of the mounting holes with a pen-

cil.

•  Drill the mounting holes (diameter 6 mm).

•  Stick the dowels (D) into the boreholes and fasten the

mounting plates to the wall with the countersunk screws 

(C).

•  Twist the threaded bolts (A) into the back side of the

sound bar so far that there is enough space between the 

wall and the connection cable.

 CAUTION: IMPORTANT!

For an optimal wall mounting we recommend the use 

of connection cables with an angled connection. You 

can obtain corresponding cables from the specialist 

shop.

•  Hang the device into the mounting plates (B) with the

screws (A). Check for stable support.

Establish a power supply and wireless subwoofer connec-

tion.

The wireless connection of the subwoofer is created automa-

tically.

•  Set up the subwoofer in a radius of 5 meters to the sound

bar.

•  Make sure the grid voltage corresponds to the figures on

the rating plate.

•  Plug the power plug of both devices into a properly

installed protective wall socket.

•  Now turn on the subwoofer by switching the power switch

on the back side of the device to the “ON” position. 

The connection is established as soon as you turn on the 

sound bar  with the       button (14). 

 NOTE: 

The lithium cell in the battery compartment of the remote 

control was possibly secured with a foil for the transport. 

This prolongs the lifetime of the battery. Please remove this 

foil before the first use to make the remote control ready 

for operation.

•  Open the battery compartment on the underside of the

remote.

•  Replace the cell with a battery of the same type (CR

2025). Check that the polarity is correct (see battery com-

partment).

•  Close the battery compartment.

If the remote is not in use for a lengthy period of time, please 

remove the battery to prevent the battery acid from “leaking”.

 WARNING: 

•  Do not expose the batteries to intense heat, such as

sunlight, fire or similar. 

Danger of explosion!

•  Keep batteries out of the reach of children. They are

not toys.

•  Do not force batteries open.

•  Avoid contact with metallic objects. (Rings, nails, screws

etc.) 

Danger of short circuits!

•  Short circuits may overheat or even ignite batteries.

This may lead to combustion.

•  When transporting the batteries, cover the terminals for

your safety with an adhesive strip.

•  If a battery leaks, do not rub the fluid into the eyes or

the skin. If acid comes into contact with the eyes, rinse 

with purified water and seek medical advice if symp-

toms persist.

 NOTE: 

•  Once the connection is established, the control light

of the subwoofer will light up. If no connection was 

established, the LED will flash. If no connection is made 

within about 5 Minutes the LED goes out.

•  Disconnect from mains power supply during longer

periods of non-use.

Insert/Replace Battery in Remote Control

•     Turn on the sound bar by switching the power switch

(5) on the backside of the device to the “ON” position.