Pioneer MVH-X460UI: Using this unit Installation

Section

Using this unit

Installation

02

03

2 Press SRC/OFF to select AUX as the

— Never wire the negative speaker cable directly

SP-P/O MODE (rear output and preout setting)

Connections

source.

to ground.

English

The rear speaker leads output and the RCA output

Important

— Never band together negative cables of multi-

Note

of this unit can be used to connect a full-range

! When installing this unit in a vehicle without

ple speakers.

AUX cannot be selected unless the auxiliary set-

speaker or subwoofer. Select a suitable option for

an ACC (accessory) position on the ignition

! When this unit is on, control signals are sent

ting is turned on. For more details, refer to AUX

your connection.

switch, failure to connect the red cable to the

through the blue/white cable. Connect this

(auxiliary input) on page 9.

1 Press M.C. to display the setting mode.

terminal that detects operation of the ignition

cable to the system remote control of an ex-

2 Turn M.C. to select the desired setting.

key may result in battery drain.

ternal power amp or the vehicle’s auto-anten-

! REAR/SUB.W – Select when there is a full-

Switching the display

na relay control terminal (max. 300 mA

range speaker connected to the rear speak-

F

F

O

N

12 V DC). If the vehicle is equipped with a

er leads output and there is a subwoofer

Selecting the desired text information

O

T

S

T

R

A

glass antenna, connect it to the antenna

connected to the RCA output.

1 Press DISP to cycle between the following:

booster power supply terminal.

! SUB.W/SUB.W – Select when there is a

! Source name

! Never connect the blue/white cable to the

ACC position No ACC position

subwoofer connected directly to the rear

! Source name and clock

power terminal of an external power amp.

speaker leads output without any auxiliary

! Use of this unit in conditions other than the

Also, never connect it to the power terminal

amp and there is a subwoofer connected

following could result in fire or malfunction.

of the auto antenna. Doing so may result in

to the RCA output.

If an unwanted display appears

— Vehicles with a 12-volt battery and negative

battery drain or a malfunction.

! REAR/REAR – Select when there is a full-

grounding.

Turn off the unwanted display using the proce-

! The black cable is ground. Ground cables for

range speaker connected to the rear speak-

— Speakers with 50 W (output value) and 4 W to

dures listed below.

this unit and other equipment (especially,

er leads output and the RCA output.

8 W (impedance value).

high-current products such as power amps)

If there is a full-range speaker connected to

1 Press M.C. to display the main menu.

! To prevent a short-circuit, overheating or mal-

must be wired separately. If they are not, an

the rear speaker leads output and the RCA

function, be sure to follow the directions

accidental detachment may result in a fire or

output is not used, you may select either

2 Turn M.C. to change the menu option

below.

malfunction.

REAR/SUB.W or REAR/REAR.

and press to select SYSTEM.

— Disconnect the negative terminal of the bat-

tery before installation.

This unit

3 Turn M.C. to display DEMO OFF and press

— Secure the wiring with cable clamps or adhe-

System menu

to select.

sive tape. Wrap adhesive tape around wiring

CAUTION

that comes into contact with metal parts to

1 Press and hold SRC/OFF until the unit

Use a USB cable when connecting a USB stor-

4 Turn M.C. to switch to YES.

protect the wiring.

turns off.

age device. Connecting a USB storage device di-

— Place all cables away from moving parts,

rectly may be dangerous because it may stick

5 Press M.C. to select.

2 Press and hold SRC/OFF until the main

such as the shift lever and seat rails.

out.

menu appears in the display.

— Place all cables away from hot places, such

as near the heater outlet.

! To use the USB port to connect a device, pre-

3 Turn M.C. to change the menu option

— Do not connect the yellow cable to the battery

pare and use a USB cable sold separately.

and press to select SYSTEM.

by passing it through the hole to the engine

! To use the AUX input jack to connect a de-

compartment.

vice, prepare and use the AUX cable sold

4 Turn M.C. to select the system menu

— Cover any disconnected cable connectors

separately.

function.

with insulating tape.

For details, refer to System menu on page 9.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

Using an AUX source

other devices. The current capacity of the

1 Use the AUX cable to connect an auxiliary

cable is limited.

device to this unit.

— Use a fuse of the rating prescribed.

En

11