Pioneer MVH-X460UI: Installation

1

2

3 5

4

76 8

1 USB port

2 Power cord input

3 Rear output or subwoofer output

4 Front output

5 AUX input jack (3.5 mm stereo jack)

6 Wired remote input

Hard-wired remote control adapter can be

connected (sold separately).

7 Fuse (10 A)

8 Antenna input

Power cord

3

4

5

6

1

2

3

4

7

5

6

8

a

9

b

d

2 Depending on the kind of vehicle, the func-

Notes

! Consult your dealer if installation requires

tion of 3 and 5 may be different. In this

! Change the initial menu of this unit. Refer to

drilling of holes or other modifications to the

case, be sure to connect 4 to 5 and 6 to

SP-P/O MODE (rear output and preout set-

vehicle.

3.

ting) on page 11.

! Do not install this unit where:

3 Yellow

The subwoofer output of this unit is monau-

— it may interfere with operation of the vehicle.

Back-up (or accessory)

ral.

— it may cause injury to a passenger as a result

4 Yellow

! When using a subwoofer of 70 W (2 W), be

of a sudden stop.

Connect to the constant 12 V supply termi-

sure to connect the subwoofer to the violet

! The semiconductor laser will be damaged if

nal.

and violet/black leads of this unit. Do not

it overheats. Install this unit away from hot

5 Red

connect anything to the green and green/

places such as near the heater outlet.

Accessory (or back-up)

black leads.

! Optimum performance is obtained when the

6 Red

unit is installed at an angle of less than 60°.

Connect to terminal controlled by ignition

Power amp (sold separately)

switch (12 V DC).

Perform these connections when using the op-

60°

7 Connect leads of the same color to each

tional amplifier.

other.

8 Black (chassis ground)

1

3

9 Blue/white

2

! When installing, to ensure proper heat dis-

The pin position of the ISO connector will dif-





4

persal when using this unit, make sure you

fer depending on the type of vehicle. Connect

55

9 and b when Pin 5 is an antenna control





leave ample space behind the rear panel and

3

wrap any loose cables so they are not block-

type. In another type of vehicle, never con-

2

ing the vents.

nect 9 and b.

1

a Blue/white





6

77

Connect to system control terminal of the





power amp (max. 300 mA 12 V DC).

b Blue/white

1 System remote control

Connect to auto-antenna relay control termi-

Connect to Blue/white cable.

nal (max. 300 mA 12 V DC).

2 Power amp (sold separately)

c Speaker leads

3 Connect with RCA cables (sold separately)

White: Front left +

4 To Front output

White/black: Front left *

5 Front speaker

Gray: Front right +

6 To Rear output or subwoofer output

Gray/black: Front right *

7 Rear speaker or subwoofer

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Installation

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

Important

d ISO connector

! Check all connections and systems before

In some vehicles, the ISO connector may be

final installation.

1 To Power cord input

divided into two. In this case, be sure to con-

! Do not use unauthorized parts as this may

nect to both connectors.

cause malfunctions.

Section

03

Installation

Installation

Leave ample

space

5 cm

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

12

En