Pioneer DEH-1700UB: Connections/Installation
Connections/Installation: Pioneer DEH-1700UB
Connections/Installation
–Never cut the insulation of the power
Connections
cable of this unit in order to share the
power with other devices. The current
Important
capacity of the cable is limited.
• When installing this unit in a vehicle
–Use a fuse of the rating prescribed.
without an ACC (accessory) position on
–Never wire the negative speaker cable
the ignition switch, failure to connect the
directly to ground.
red cable to the terminal that detects
–Never band together negative cables of
operation of the ignition key may result
multiple speakers.
in battery drain.
• When this unit is on, control signals are
sent through the blue/white cable.
Connect this cable to the system remote
control of an external power amp or the
vehicle’s auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
• Use of this unit in conditions other than
vehicle is equipped with a glass antenna,
the following could result in fire or
connect it to the antenna booster power
malfunction.
supply terminal.
–Vehicles with a 12-volt battery and
• Never connect the blue/white cable to
negative grounding.
the power terminal of an external power
–Speakers with 50 W (output value) and
amp. Also, never connect it to the power
4 Ω to 8 Ω (impedance value).
terminal of the auto antenna. Doing so
• To prevent a short-circuit, overheating or
may result in battery drain or a
malfunction, be sure to follow the
malfunction.
directions below.
• The black cable is ground. Ground cables
–Disconnect the negative terminal of the
for this unit and other equipment
battery before installation.
(especially, high-current products such as
–Secure the wiring with cable clamps or
power amps) must be wired separately. If
adhesive tape. Wrap adhesive tape
they are not, an accidental detachment
around wiring that comes into contact
may result in a fire or malfunction.
with metal parts to protect the wiring.
– Place all cables away from moving parts,
This unit
such as the shift lever and seat rails.
–Place all cables away from hot places,
such as near the heater outlet.
–Do not connect the yellow cable to the
battery by passing it through the hole
to the engine compartment.
–Cover any disconnected cable
Power cord input
connectors with insulating tape.
Rear output or subwoofer output
–Do not shorten any cables.
Antenna input
Fuse (10 A)
10En
ACC position No ACC position
Wired remote input (Not available for
Blue/white
DEH-1700UBA)
The pin position of the ISO connector
Hard-wired remote control adapter can
will differ depending on the type of
be connected (sold separately).
vehicle. Connect and when Pin 5
is an antenna control type. In another
Power cord
type of vehicle, never connect and
.
Blue/white
Connect to the system control terminal
of the power amp (max. 300 mA 12 V
DC).
Blue/white
Connect to the auto-antenna relay
control terminal (max. 300 mA 12 V DC).
Yellow/black (Not available for DEH-
1700UBA)
If you use equipment with a Mute
function, wire this lead to the Audio
Mute lead on that equipment. If not,
keep the Audio Mute lead free of any
connections.
Speaker leads
White: Front left
White/black: Front left
Gray: Front right
To power cord input
Gray/black: Front right
Depending on the kind of vehicle, the
Green: Rear left or subwoofer
function of and may be different.
Green/black: Rear left or subwoofer
In this case, be sure to connect to
and to .
Violet: Rear right or subwoofer
Yel low
Violet/black: Rear right or subwoofer
Back-up (or accessory)
Yel low
ISO connector
Connect to the constant 12 V supply
In some vehicles, the ISO connector
terminal.
may be divided into two. In this case, be
Red
sure to connect to both connectors.
Accessory (or back-up)
NOTES
Red
• Change the initial menu of this unit. Refer
Connect to terminal controlled by the
to [SP-P/O MODE] (page 5). The
ignition switch (12 V DC).
subwoofer output of this unit is
Connect leads of the same color to each
monaural.
other.
Black (chassis ground)
• When using a subwoofer of 70 W (2 Ω), be
• When installing, to ensure proper heat
sure to connect the subwoofer to the
dispersal when using this unit, make sure
violet and violet/black leads of this unit.
you leave ample space behind the rear
Do not connect anything to the green
panel and wrap any loose cables so they
and green/black leads.
are not blocking the vents.
Power amp (sold separately)
English
Perform these connections when using the
optional amplifier.
System remote control
DIN front/rear mount
Connect to blue/white cable.
This unit can be properly installed using
Power amp (sold separately)
either front-mount or rear-mount
Connect with RCA cables (sold
installation.
separately)
Use commercially available parts when
To rear output or subwoofer output
installing.
Rear speaker or subwoofer
DIN Front-mount
1 Insert the mounting sleeve into the
Installation
dashboard.
For installation in shallow spaces, use
Important
the supplied mounting sleeve. If there is
• Check all connections and systems before
enough space, use the mounting sleeve
final installation.
that came with the vehicle.
• Do not use unauthorized parts as this
2 Secure the mounting sleeve by using a
may cause malfunctions.
screwdriver to bend the metal tabs
• Consult your dealer if installation requires
(90°) into place.
drilling of holes or other modifications to
the vehicle.
• Do not install this unit where:
–it may interfere with operation of the
vehicle.
–it may cause injury to a passenger as a
result of a sudden stop.
• The semiconductor laser will be damaged
if it overheats. Install this unit away from
Dashboard
hot places such as near the heater outlet.
Mounting sleeve
• Optimum performance is
• Make sure that the unit is installed
obtained when the unit is
securely in place. An unstable
installed at an angle of less
installation may cause skipping or
than 60°.
other malfunctions.
11En
Leave ample
5 cm
space
5 cm
DIN Rear-mount
1 Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
2 Tighten two screws on each side.
Tapping screw (5 mm × 8 mm)
Mounting bracket
Dashboard or console
Removing the unit
1 Remove the trim ring.
Trim ring
Notched tab
• Releasing the front panel allows easier
access to the trim ring.
• When reattaching the trim ring, point
the side with the notched tab down.
2 Insert the supplied extraction keys
into both sides of the unit until they
click into place.
3 Pull the unit out of the dashboard.
Оглавление
- Table of Contents
- Before You Start
- Getting Started
- Radio
- CD/USB/AUX
- Settings
- Connections/Installation
- Additional Information
- Table des matières
- Avant de commencer
- Mise en route
- Radio
- CD/USB/AUX
- Réglages
- Raccordements/Installation
- Informations complémentaires
- Sommario
- Prima di iniziare
- Operazioni preliminari
- Radio
- CD/USB/AUX
- Impostazioni
- Connessioni/Installazione
- Informazioni aggiuntive
- Índice
- Antes de empezar
- Procedimientos iniciales
- Radio
- CD/USB/AUX
- Ajustes
- Conexiones/instalación
- Información complementaria
- Inhaltsverzeichnis
- Bevor Sie beginnen
- Erste Schritte
- Radio
- CD/USB/AUX
- Einstellungen
- Anschlüsse/Einbau
- Zusätzliche Informationen
- Inhoud
- Vóór u begint
- Aan de slag
- Radio
- CD/USB/AUX
- Instellingen
- Verbindingen/installatie
- Aanvullende informatie
- Содержание
- Перед началом эксплуатации
- Начало работы
- Радио
- Компакт-диск/USB/AUX
- Настройки
- Подключения/Установка
- Дополнительная информация