AEG sr4352: English

32

English

NOTE:

NOTE:

After approx. 15 minutes without a signal, the device will

In the case of CDs in MP3 format the number of folders

automatically switch to standby. To use the device again,

is briefly displayed at first.

press the

/ button (8).

5. Press the

/ button (8) to restart playback. The CD

will play from the first title. The current track and the “CD

AUX IN jack

“ or “MP3 “ message are shown on the display.

1. Connect the 3.5 mm stereo RCA cable to an external

NOTE:

audio source. If required, use a suitable adapter (not

With CDs in MP3 format the current track and folder

included).

are shown alternately in the display.

2. Insert the other end of the cable into the AUX-IN jack

(Back Side) on the unit.

6. In order to remove a CD, please press the

STOP button

3. Set the function selector switch (19) to the “CD/MP3/

(16), open the CD compartment and lift the CD out care-

AUX” position.

fully.

4. Start the playback of your audio source. Listen to the

Always keep the CD deck closed.

sound playback via the speaker.

NOTE:

5. For the further procedure, please refer to the user manual

• If a disc is inserted the wrong way, or if no disc is

of the external audio source.

inserted, the message “– – –” will flash and “NOd” will

NOTE:

appear on the display.

If possible, adjust the volume of the external unit to a com-

• Playback of CDs produced by the user cannot be

fortable level.

guaranteed due to the large variety of software and CD

media available.

Listening to the Radio

Description of the CD buttons

1. Set the function selector switch (19) to the “RADIO” posi-

tion.

/ (8)

2. Select the desired frequency band with the band selector

You can briefly interrupt and resume playback using this

switch (4).

button. The symbol“

“ flashes on the display. Pressing again

VHF (Stereo) = FM.ST, Medium wave = AM (Mono)

continues playback.

2. Tune in the desired station with the station adjustment

NEXT/ BACK (9/15)

knob TUNING (6).

3. The FM ST. indicator lamp (13) will only be lit, when the

When playing an audio CD or a CD in MP3 format:

station is received in stereo quality. If reception is too

With NEXT you can jump to the next or previous track etc.

weak and there is noise on the station being received,

• If the button is kept pressed down, the machine starts to

this lamp will flicker.

search through the tracks.

4. For FM mode pull out the telescopic antenna (2) and turn

it to improve reception.

The

BACK button can be used as follows:

5. An aerial is integrated into the device for the reception of

Press once = This jumps back to the previous track.

AM stations. The machine can be aligned to the station

Press twice = This plays the song before etc. If the button

by turning it. In this frequency band programs are trans-

is kept pressed down, the machine starts to

mitted in “mono” only.

search through the tracks.

STOP (16)

Playing CDs/MP3

The CD stops.

This is how you play a CD

1. Turn the function selector switch (19) to the “CD/MP3/

PROG./P-MODE (12)

AUX”.

• In stop mode for programming any order of tracks (see

2. Open the CD tray (3) by pressing the PUSH OPEN button

the section on “Programmed Play”).

(7).

• When playing back music to select the replay mode (see

3. Insert an audio CD with the printed side facing upwards

next chapter).

on to the central cone so that the CD clicks into place

and then close the lid of the CD compartment.

When playing an audio CD:

4. After a few seconds the total number of songs/tracks is

Press once = (The symbol

flashes) the current track

shown in the display.

is repeated continuously.