Vitek VT-1255: ENGLISH
ENGLISH: Vitek VT-1255
ENGLISH
have been given supervision or instruction
cloth to be sure that the iron sole (12) and the
concerning use of the appliance by a person
water tank (11) are clean.
responsible for their safety
• Always check the recommended iron tem-
• Children should be supervised to ensure that
perature indicated on the tag before ironing.
they do not play with the appliance
• If the tag does not list the recommended
ironing temperature, but you know the type
BEFORE USAGE
of fabric, then use the following table to de-
• Take out the iron from the package and re-
termine the proper temperature.
move the protective cartoon covering from
Signs Fabric type/temperature
the iron sole (12).
Synthetics, nylon, acryl, polyester
•
• Make sure that the electrical supply voltage
(low temperature)
corresponds to the iron’s operating voltage.
••
Silk/wool (medium temperature)
•••
Cotton/flax (high temperature)
Note:
The iron’s heating element is broken in
• This table is only for smooth materials.
during the first use; it is normal for a small
Fabrics of other types (crimped, raised etc.)
amount of smoke to be released.
are best ironed at low temperature.
• First sort items by ironing temperature: wool
CHOICE OF WATER
with wool, cotton with cotton etc.
To fill the water tank use regular tap water. If the
• The iron heats up faster than is cools down.
water is hard then it is recommended to mix it
For this reason it is recommended to begin
with distilled water at a ratio of 1:1, if the water
ironing at low temperature (for instance syn-
is very hard, mix it with distilled water at a ratio
thetic fabrics). After that, move to higher tem-
of 1:2 or use only distilled water.
perature ironing. Cotton and linens should be
ironed last.
Note:
• If an item is made from a mix of fabrics, then
Do not fill the water tank (11) with scented
the iron should be set for the fabric with
liquids, vinegar, starch solutions, descal-
the lowest ironing (for instance if an item is
ing reagents, chemical substances etc.
made from 60% polyester and 40% cotton, it
should be ironed at the temperature used for
FILLING THE WATER TANK (pic. 1, 2)
ironing polyester “•”).
Make sure that the iron is disconnected from
• If you cannot define the fabric the item is
electrical power before filling it with water.
made from, find a place on it that is hidden
Set the steam release regulator (3) to the Off
while wearing and, on practice select the
position.
ironing temperature (always start at the low-
• Open the water tank lid (2).
est and gradually raise it until you get the de-
• Fill it with water using the water bowl (14).
sired result.)
Close the lid (2).
• Corduroy and other fabrics that start glossy
quickly should be ironed strictly in one direc-
Note:
tion (along the lines) with slight pressure.
• Do not fill it with water above MAX. indi-
• To avoid appearance of glossy spots on the
cation.
synthetic and silk fabrics, iron them back-
• If you need to refill the water tank during
side.
ironing, turn off the iron and unplug the
power cord from the outlet.
SETTING THE IRONING TEMPERATURE
• After you finish ironing, open the water
• Place the iron on the base (8).
tank lid (2) and drain the remaining water
• Insert the power plug into the outlet.
(pic.8).
• Set the temperature regulator (10) to the re-
quired ironing temperature: “•”, “••”, “•••”
IRONING TEMPERATURE
(depending on the type of fabric), the (9) in-
Before operating test the heated iron on the old
dicator will light up (Pic.3).
5
1255.indd 51255.indd 5 03.03.2010 15:40:1503.03.2010 15:40:15