Pioneer PD-50-S: Connecting up
Connecting up: Pioneer PD-50-S
Connecting up 02
English
Chapter 2:
Connecting up
• When connecting optical fiber cables, align the
Caution
connectors correctly and insert fully. If the
• Before making or changing the connections,
orientation of the cable connector is incorrect and
switch off the power and disconnect the power cord
excessive force is applied in the attempt to fasten
from the AC outlet.
the connector, the connector may be deformed,
• Connect the power cord after all the connections
preventing the shutter from closing when the cable
between devices have been completed.
is removed.
Digital audio output connections
DeutschFrançais
If desired, the digital audio output from this unit can be
Analog audio output connections
connected to an AV amplifier or digital recording device
By connecting this unit’s analog audio output to the
(CD recorder, MD, etc.).
analog audio input of an amplifier, you can use the
• This unit’s DIGITAL OUT terminals do not output
amplifier to enjoy analog audio produced from this unit.
sound from SACD and DSD discs, nor from iPod/
iPhone/iPad devices.
Italiano Español Русский
DIGITAL IN
Nederlands
RL
ANALOG
AUDIO INPUT
Digital audio connections
Important
Care in the handling of optical fiber cables
• Do not allow optical fiber cables to be bent at sharp
angles. When storing optical fiber cables, roll in
coils of at least 15 cm diameter.
5
En
PD-50’s rear panel
Audio cable (included)
Amplifier
DIGITAL IN
COAXIAL
DIGITAL IN
OPTICAL
DIGITAL IN
AV amplifier or
digital recording
device
AV amplifier or
digital recording
device
Coaxial digital
audio cable
Optical fiber cable
(commercially
(commercially
available)
available)
PD-50’s rear panel
Note
Using centralized control with other
• For digital audio output, CDs played on this unit
must produce linear PCM signals with a sampling
Pioneer components
rate up to 44.1 kHz and quantitative bits up to 16
This unit and other Pioneer components equipped with
bits (some discs may not be playable depending on
CONTROL IN/OUT jacks can be controlled with a single
the connected component and environment). For
remote control by aiming the remote toward the signal
information about other files, see page 14.
receptor on the AV amplifier or other component. This
also allows remote control of components not equipped
Digital audio input connections
with a remote sensor, or installed in places where the
This unit can be used as a D/A converter by connecting
component’s remote sensor cannot be accessed.
the digital audio output of a digital audio component to
the digital audio input of this unit.
See the section “Using this unit as a D/A converter”
(page 12) for details about the audio output of signals
input to this unit’s DIGITAL IN terminals.
Note
• For connections use a commercially available
monaural miniplug cord (without resistor).
• When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
Note
not allow proper system control.
• This unit supports linear PCM signals with
• When a control cord is connected to the PD-50’s
sampling rates and quantitative bits up to 192 kHz/
CONTROL IN jack, the PD-50 cannot be controlled
24 bits (operation may not be possible in all cases,
by pointing the remote control at the unit's remote
depending on components connected and
sensor (the sensor is automatically disabled).
operating environment).
DIGITAL IN
DIGITAL IN
COAXIAL
DIGITAL IN
OPTICAL
Digital audio 1
Digital audio 2
Coaxial digital
audio cable
(commercially
available)
Optical fiber cable
(commercially
available)
PD-50’s rear panel
Other Pioneer component
equipped with CONTROL
IN/OUT jacks
Remote control for
AV amplifier, etc.
Point the remote
control toward the
signal receiver on
the AV amplifier, etc.
To other Pioneer
component equipped
with CONTROL IN jack
PD-50
PD-50_PWSYXZT8.book 5 ページ 2012年7月6日 金曜日 午前11時12分
Connecting up02
Plugging in
Important
• If it is necessary to detach the power cord, first be
sure to press the
/I
STANDBY/ON button on the
front panel of the unit so the PD-50 is turned OFF.
• Confirm that the [-OFF-] indicator is not lighted in
the main unit’s front panel display before
disconnecting the power cord. If the power cord is
disconnected while the [-OFF-] indicator is still
lighted, the unit’s settings may revert to factory
defaults.
• When going on a trip or otherwise not using the
unit for an extended period, always disconnect the
power cord from its outlet.
Caution
• Do not use any power cord other than the one
supplied with this unit.
• Do not use the supplied power cord for any purpose
other than that described below.
After you’ve finished making all connections, plug the
unit into an AC outlet.
1 Plug the supplied power cord into the
AC IN
socket on the rear of the unit.
2 Plug the other end into AC outlet.
6
En
PD-50’s rear panel
To AC outlet
Power cord
(included)
PD-50_PWSYXZT8.book 6 ページ 2012年7月6日 金曜日 午前11時12分
Оглавление
- PD-50-K/-S
- Before you start
- Connecting up
- Controls and displays
- Playback
- Using advanced functions
- Additional information
- Avant de commencer
- Connexions
- Commandes et écrans
- Lecture
- Les fonctions avancées
- Informations complémentaires
- Bevor Sie beginnen
- Anschließen
- Bedienelemente und Anzeigen
- Wiedergabe
- Erweiterte Funktionen
- Zusätzliche Informationen
- Prima di iniziare
- Collegamento
- Controlli e display
- Riproduzione
- Utilizzo delle funzioni avanzate
- Informazioni aggiuntive
- Voordat u begint
- Aansluitingen
- Bedieningsorganen en display-
- Afspelen
- Geavanceerde functies gebruiken
- Extra informatie
- Antes de comenzar
- Conexiones
- Controles y visualizadores
- Reproducción
- Utilizar funciones avanzadas
- Información adicional
- Подготовка к использованию
- Подключение
- Органы управления и индикации
- Воспроизведение
- Использование дополнительных
- Дополнительная информация