AEG PW 5644 FA 520706 Белый, серебристый: English

English

37

This device has been tested according to all relevant current

Saving Personal Data

CE guidelines, such as electromagnetic compatibility and low

NOTE:

voltage directives, and has been constructed in accordance

• The scale has default values that you can change, as

with the latest safety regulations.

described below.

• Carry out the following steps in sequence and within a

Information about the Analysis Scale

few seconds. Otherwise, the device will automatically

cancel input mode.

WARNING:

• Press the button SET. The memory space (P0) will flash on

Do not use the scales if you use a pacemaker or another

the display. Confirm the setting by pressing SET or select

medical implant with electronic components. The function

another memory space by pressing the UP / DOWN but-

of the implant may be impaired by the measurement.

ton. Then press SET to go to the next setting.

• The symbol for “male” or “female” will ash. Conrm the

The main principle of this device is based on the measure-

setting by pressing SET or use the UP / DOWN button to

ment of the electric impedance within the human body. In

choose the symbol for your gender. Then press SET to go

order to determine the actual body data, the device leads a

to the next setting.

weak, unnoticeable electric signal through your body.

• The height setting will ash. Select your height by press-

The signal is generally safe! However, please read our special

ing UP or DOWN button. Holding down one of the

safety instructions!

buttons will accelerate the process. Confirm your entry by

The method of measurement is referred to as “bioelectric

pressing SET.

impedance analysis” (BIA), a factor which is based on the re-

• The setting AGE will ash. Select your age by pressing UP

lationship between body weight and associated body water

or DOWN button. Holding down one of the buttons will

percentages as well as on other biological data (age, gender,

accelerate the process. Confirm your entry by pressing

body weight).

SET.

• The short display “- - - -” will terminate the entry mode

for this memory location. Then you will see the memory

Use

location, the symbol of the gender and the weight

“0.0 kg” (0.0 lb / 0: 0 st:lb) in the display.

NOTE:

You now have the following options:

• You will nd the buttons for the operation on the top

edge of the scale.

• You can change the units for weight and type. Press the

• The scales are factory set with the units “kg” and “cm”.

UP button

, until the desired unit of weight is displayed.

The unit for the height automatically changes.

To change the settings to “lb” or “st:lb”as well as “ft:in”,

• Press the SET button to see the selected settings again.

proceed as follows:

• Allocate further memory spaces. There are 10 spaces

• Switch the scales on by applying gentle pressure on the

available in total. Press SET and change the space by

glass surface with your foot or toe.

pressing the UP or DOWN button. Proceed further as

• Press the UP button

, until the required unit of weight

described above.

is displayed. The unit for the height also automatically

• If you want to make changes, press SET (the memory

changes.

location will blink). Select the stored position using the UP

or DOWN button. Proceed further as described above.

Weighing Function

• You can immediately start measuring.

• Place the scale on a hard, at surface (avoid carpets). An

Measurement and Analysis

uneven floor contributes to inaccurate measurements.

• Stand on the scales with both feet. The device switches

Record your personal data in the memory.

on automatically.

NOTE:

• Distribute your weight equally and wait for the scale to

• The analysis scale will only work correctly when you are

determine your weight.

standing on the contact surfaces barefoot and with

• The digits on the display will ash before your exact

slightly moistened foot soles, if possible. Completely

weight will be shown.

dry foot soles can lead to unsatisfactory results as they

• In order to extend the battery life, the device will auto-

have a conductivity that is too low.

matically turn off 15 seconds after you have stepped off

• If necessary wipe the contact surfaces to improve

the scale.

results.

• If there is no weight determination while “0.0” is shown,

the scale will shut off automatically after 15 seconds.