Pioneer FH-X360UB: Installation

Power cord

3

4

2

5

6

1

3

4

7

5

6

8

a

9

b

e

9 Blue/white

Power amp (sold separately)

! When installing, to ensure proper heat dis-

The pin position of the ISO connector will dif-

persal when using this unit, make sure you

Perform these connections when using the op-

fer depending on the type of vehicle. Connect

leave ample space behind the rear panel and

tional amplifier.

9 and b when Pin 5 is an antenna control

wrap any loose cables so they are not block-

type. In another type of vehicle, never con-

1

3

ing the vents.

nect 9 and b.

2

a Blue/white





4

Connect to system control terminal of the

55





power amp (max. 300 mA 12 V DC).

b Blue/white

1 System remote control

Connect to auto-antenna relay control termi-

Connect to Blue/white cable.

nal (max. 300 mA 12 V DC).

2 Power amp (sold separately)

c Yellow/black

3 Connect with RCA cables (sold separately)

If you use an equipment with Mute function,

4 To Rear output or subwoofer output

wire this lead to the Audio Mute lead on that

5 Rear speaker or subwoofer

equipment. If not, keep the Audio Mute lead

free of any connections.

c

d Speaker leads

Installation

White: Front left +

White/black: Front left *

Important

Gray: Front right +

! Check all connections and systems before

1 To power cord input

Gray/black: Front right *

final installation.

2 Depending on the kind of vehicle, the func-

Green: Rear left + or subwoofer +

! Do not use unauthorized parts as this may

tion of 3 and 5 may be different. In this

Green/black: Rear left * or subwoofer *

cause malfunctions.

case, be sure to connect 4 to 5 and 6 to

Violet: Rear right + or subwoofer +

! Consult your dealer if installation requires

3.

Violet/black: Rear right * or subwoofer *

drilling of holes or other modifications to the

3 Yellow

e ISO connector

vehicle.

Back-up (or accessory)

In some vehicles, the ISO connector may be

! Do not install this unit where:

4 Yellow

divided into two. In this case, be sure to con-

— it may interfere with operation of the vehicle.

Connect to the constant 12 V supply termi-

nect to both connectors.

— it may cause injury to a passenger as a result

nal.

of a sudden stop.

Notes

5 Red

! The semiconductor laser will be damaged if

Accessory (or back-up)

! Change the initial menu of this unit. Refer to

it overheats. Install this unit away from hot

6 Red

SP-P/O MODE (rear output and preout set-

places such as near the heater outlet.

Connect to terminal controlled by ignition

ting) on page 7.

! Optimum performance is obtained when the

switch (12 V DC).

The subwoofer output of this unit is monau-

unit is installed at an angle of less than 60°.

7 Connect leads of the same color to each

ral.

other.

! When using a subwoofer of 70 W (2 W), be

60°

8 Black (chassis ground)

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

Leave ample

space

5 cm

5 cm

! Use commercially available parts when in-

stalling.

How to install

This unit can be installed properly using either

of the methods in the below list.

! Installation with the holder

! Installation using the screw holes on the side

of the unit

Before installing this unit

1 Remove the trim ring.

Section

Installation

Installation

03

English

1 Trim ring

En

9