Pioneer MVH-150UBG: Installation

Black plate (9,1)

Power cord

3

4

2

5

6

1

3

4

7

5

6

8

a

9

b

d

9 Blue/white

Power amp (sold separately)

! When installing, to ensure proper heat dis-

The pin position of the ISO connector will dif-

Perform these connections when using the op-

persal when using this unit, make sure you

fer depending on the type of vehicle. Connect

leave ample space behind the rear panel and

tional amplifier.

9 and b when Pin 5 is an antenna control

wrap any loose cables so they are not block-

type. In another type of vehicle, never con-

1

3

ing the vents.

nect 9 and b.

2

a Blue/white





4

Connect to system control terminal of the

55

power amp (max. 300 mA 12 V DC).





b Blue/white

1 System remote control

Connect to auto-antenna relay control termi-

Connect to Blue/white cable.

nal (max. 300 mA 12 V DC).

2 Power amp (sold separately)

c Speaker leads

3 Connect with RCA cables (sold separately)

White: Front left +

4 To Rear output or subwoofer output

White/black: Front left *

5 Rear speaker or subwoofer

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Installation

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Important

Violet/black: Rear right * or subwoofer *

! Check all connections and systems before

1 To power cord input

d ISO connector

final installation.

2 Depending on the kind of vehicle, the func-

In some vehicles, the ISO connector may be

! Do not use unauthorized parts as this may

tion of 3 and 5 may be different. In this

divided into two. In this case, be sure to con-

cause malfunctions.

case, be sure to connect 4 to 5 and 6 to

nect to both connectors.

! Consult your dealer if installation requires

3.

drilling of holes or other modifications to the

Notes

3 Yellow

vehicle.

Back-up (or accessory)

! Change the initial menu of this unit. Refer to

! Do not install this unit where:

4 Yellow

SP-P/O MODE (rear output and preout set-

— it may interfere with operation of the vehicle.

Connect to the constant 12 V supply termi-

ting) on page 7.

— it may cause injury to a passenger as a result

nal.

The subwoofer output of this unit is monau-

of a sudden stop.

5 Red

ral.

! The semiconductor laser will be damaged if

Accessory (or back-up)

! When using a subwoofer of 70 W (2 W), be

it overheats. Install this unit away from hot

6 Red

sure to connect the subwoofer to the violet

places such as near the heater outlet.

Connect to terminal controlled by ignition

and violet/black leads of this unit. Do not

! Optimum performance is obtained when the

switch (12 V DC).

connect anything to the green and green/

unit is installed at an angle of less than 60°.

7 Connect leads of the same color to each

black leads.

other.

60°

8 Black (chassis ground)

Section

Installation

Installation

03

English

Leave ample

space

5 cm

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

En

9

<QRB3391-A>9