Karcher B 150 R Bp: Operation

     

- 

5



Bring the safety switch into the "1" posi-

tion.



Set programme selector switch to trans-

port run.



Set the travel direction switch to "for-

ward".



Actuate the accelerator pedal.



Drive the appliance off the pallet.



Bring the safety switch into the "0" posi-

tion.

The procedure for changing the cleaning 

head is described in the chapter "Mainte-

nance Tasks".

Note:

On some models, the cleaning head is al-

ready installed.

The installation of the brushes is described 

in the chapter "Maintenance Tasks".



Insert the vacuum bar into the vacuum 

bar suspension in such a manner that 

the profiled sheet is positioned above 

the suspension.



Tighten the wing nuts.



Insert the suction hose.



DANGER

Risk of injuries. Never use the unit without 

protective roof in areas where the opera-

tors can be hit by dropping objects. 

Note:

To take all functions out of operation imme-

diately, bring the safety switch into the "0" 

position.



Operate the lever for the seat adjust-

ment and move the seat to the desired 

position.



Release the seat adjustment lever and 

lock the seat in place.



Take the seating position.  



Plug in the Intelligent Key.



Bring the safety switch into the "1" posi-

tion.



Turn the programme switch to the de-

sired function.



DANGER

Risk of accident. Prior to every operation, 

the parking brake must be checked for 

proper function on a level ground.



Turn on the appliance.



Set the travel direction switch to "for-

ward".



Set programme selector switch to trans-

port run.



Gently depress drive pedal.



The brake must unlock audibly. The ma-

chine must roll easily on a plane surface. 

When the pedal is released, the brake 

locks audibly. Switch off the machine and 

call the aftersales service if the above-

mentioned events do not occur.



DANGER

Danger of accident. If the machine does not 

brake, then proceed as follows:



If the appliance does not stop when the 

accelerator is released on a ramp with 

more than 2% inclination, the safety 

switch may only be brought in the "0" 

position if the proper mechanical func-

tion of the parking brake has been 

checked prior to every operation of the 

appliance for safety reasons.



Switch off the machine only after it 

comes to a complete halt (on an even 

surface) and call up the aftersales ser-

vice!



Further, follow all warning instructions 

for braking.



DANGER

Danger of tipping if gradient is too high.



The gradient in the direction of travel 

should not exceed 10%.

Danger of tipping when driving round 

bends at high speed.

Danger of slipping on wet floors.



Drive slowly when cornering.

Danger of tipping on unstable ground.



Only use the machine on sound surfac-

es.

Danger of tipping with excessive sideways 

tilt.



The gradient perpendicular to the direc-

tion of travel should not exceed 10%.



Take the seating position.  



Plug in the Intelligent Key.



Bring the safety switch into the "1" posi-

tion.



Set programme selector switch to trans-

port run.



Set the drive direction using the drive 

direction button at the operator console. 



Determine the driving speed by press-

ing the drive pedal. 



Stop the machine: Release the drive 

pedal.

Note:

The direction of travel can also be changed 

while driving. This way even very dull spots 

can be polished by driving back and forth 

several times.

In case of overloading, the drive motor au-

tomatically switches off after a certain peri-

od. A fault message is displayed on the 

console. The concerned unit gets switched 

off if the controls get overheated.



Allow machine to cool down at least for 

15 minutes. 



Turn the programme switch to "OFF", 

wait for a short period of time and turn it 

back to the desired programme.

ATTENTION

Risk of damage. Only use the recommend-

ed detergents. With respect to different de-

tergents the operator bears the increased 

risk regarding the operational safety and 

danger of accident.

Only use detergents that are free from sol-

vents, hydrochloric acid and hydrofluoric 

acid.

Follow the safety instructions for using de-

tergents.

Note:

Do not use highly foaming detergents.



Open the cover of the fresh water reser-

voir.



Fill fresh water (max. 60 °C) until 15 mm 

below the upper edge of the tank.



Pour in detergent.

Note:

If detergent is added to the detergent tank 

first before the water, this can result in a for-

mation of a lot of foam.



Close the cover of the fresh water res-

ervoir.

Note:

fresh water tank completely prior to the ini-

tial commissioning

Install cleaning head

Installing the Brushes

Installing the Vacuum Bar

Operation

Adjusting driver's seat

Turning on the Appliance

Check parking brake

Driving

Driving

Overload

Filling in detergents

Detergent

Application

Detergent

Routine cleaning of all wa-

ter resistant floors

RM 746

RM 780

Routine cleaning of glossy 

surfaces (e.g. granite)

RM 755 es

Routine cleaning and ba-

sic cleaning of industrial 

floors

RM 69 ASF

Routine cleaning and ba-

sic cleaning of fine stone-

ware tiles

RM 753

Routine cleaning of tiles in 

sanitary areas

RM 751

Cleaning and disinfection 

in sanitary areas

RM 732

Removal of coating from 

all alkali-resistant floors 

(e.g. PVC)

RM 752

Removal of coating from li-

noleum floors

RM 754

Fresh water

20 EN