Karcher B 150 R Bp: Transport

     

- 

7

In this menu item the authorisations for yel-

low intelligent keys as well as the 

language of the display texts are selected.



Turn the info button until "key man-

agem." is shown on the display.



Press Info button.



Remove the grey Intelligent Key and in-

sert the yellow Intelligent Key to be pro-

grammed.



Select the desired menu item to be 

modified by turning the Info button.



Press Info button.



Adjust the menu item by turning the Info 

button.



Confirm the setting by pressing the 

menu item.



Select the next menu item to be modi-

fied by turning the Info button.



In order to save the authorisations, call 

the "Save?" menu by turning the info 

button and then press the info button.



"Continue key menu":

Yes: Programme further Intelligent Key.

No: Exit key menu.



Press Info button.

This function is required when changing the 

cleaning head.



Turn the info button until "brush head" is 

shown on the display.



Press Info button.



Turn the info button until the desired 

brush shape is highlighted.



Press Info button.



Move the hoist drive for replacement of 

the cleaning head by turning the info 

button:

up: Raise

down: Lower

OFF: Stop



Exit menu: Select "OFF" by turning the 

info button and press the info button.

When exiting the menu, the control per-

forms a restart.



Turn the info button until "stopping 

times" is shown on the display.



Press Info button.



Turn the info button until the desired as-

sembly is highlighted.



Press Info button.



Turn the info button until the desired 

stopping time is reached.



Press Info button.



Turn the info button until "Battery menu" 

is displayed.



Press Info button.



Turn the info button until the desired 

battery type is highlighted.



Press Info button.

Changes of the parameters of the individu-

al cleaning programmes that were made 

during the operation are reset to the basic 

setting after switching off the appliance.



Turn the info button until "Basic setting" 

is displayed.



Press Info button.



Turn the info button until the desired 

cleaning programme is displayed.



Press Info button.



Turn the info button until the desired pa-

rameter is displayed.



Press Info button - the set value blinks.



Set the desired value by turning the info 

button.



Press Info button.



Turn the info button until "Language" is 

displayed.



Press Info button.



Turn the info button until the desired 

language is highlighted.



Press Info button.

The factory settings of all parameters are 

restored.

Parameters that are adjusted with the grey 

Intelligent Key, are kept until another set-

ting is selected.



Turn the program selection switch to 

the desired cleaning program. 



Press the info button - the first adjusta-

ble parameter is displayed.



Press Info button - the set value blinks.



Set the desired value by turning the info 

button.



Confirm the changed setting by press-

ing the Info button or wait till the set val-

ue is automatically accepted after 10 

seconds. 



Select the next parameter by turning 

the Info button.



After all desired parameters have been 

modified, turn the info button until "Exit 

menu" is displayed.



Press the info button - you will exit the 

menu.



DANGER

Risk of injury! When loading or unloading 

the machine, it may only be operated on 

gradients of max. 10%. Drive slowly.

몇

CAUTION

Risk of injury and damage! Observe the 

weight of the appliance when you transport 

it.



When transporting in vehicles, secure 

the appliance according to the guide-

lines from slipping and tipping over.



Remove brushes from the brush head.

몇

CAUTION

Risk of injury and damage! Note the weight 

of the appliance in case of storage.



This appliance must only be stored in 

interior rooms.



Select the storage site for the appliance 

taking into consideration the permissi-

ble total weight of the appliance in order 

not to impact its stability.



DANGER

Risk of injury! Before working on the appli-

ance, remove the Intelligent Key and the 

mains plug of the charger.

Pull out the battery plug.



Drain and dispose of the dirt water and 

the residual fresh water.

몇

CAUTION

Risk of injury due to overrun of the suction 

turbine.

Suction turbine will continue to run for a 

while after switch-off. Carry out mainte-

nance tasks only after the suction turbine 

has come to a halt.

ATTENTION

Risk of damage. Do not sluice the appli-

ance with water and do not use aggressive 

detergents.



Drain off dirt water.



Clean protective turbine strainer.



Only with R cleaning head Remove bulk 

waste container and empty it.



Clean the outside of the appliance with 

a damp cloth which has been soaked in 

mild detergent.



Clean the vacuum lips and the wiping 

lips, check for wear and replace if re-

quired.



Check the brushes for wear, replace if 

required.



Charge battery.



During long operating pauses: Carry 

out refill charging for the battery. 



Check battery poles for oxidation, brush 

off if necessary. Ensure firm seating of 

the connection cable.



Clean the seals between dirt water res-

ervoir and cover and check for tight-

ness, replace if required.



Check the acid density of the cells if the 

batteries are not maintenance-free bat-

teries.



Clean the brush tunnel (only R cleaning 

head)



Remove the water distribution strip from 

the cleaning head and clean water ca-

nal (only R cleaning head).



Have the prescribed inspection carried 

out by the customer service.

Key management

Selecting the brush shape

Stopping times

Setting the battery type

Standard setting

Setting the language

Factory setting

Cleaning Programs

Transport

With mounted D cleaning head

Storage Maintenance and care

Maintenance schedule

After the work

Monthly

Yearly

22 EN

     - 

8

To ensure a reliable operation of the appli-

ance maintenance contracts can be con-

cluded with the competent Kärcher sales 

office.



Open the cover of the wastewater res-

ervoir.



Squeeze the locking hooks.



Pull off the float.



Turn the protective turbine strainer in a 

counter-clockwise direction.



Remove protective turbine strainer.



Rinse dirt off the protective turbine 

strainer with water.



Reattach protective turbine strainer.



Attach float.



Remove the vacuum bar.



Unscrew the star grips.



Remove the plastic parts.



Remove the vacuum lips.



Insert new vacuum lips.



Insert the plastic parts.



Screw in and tighten the star grips.



Lift the holder of the cleaning head (see 

Chapter "Grey intelligent key/.../clean-

ing head replacement".



Slide the cleaning head under the appli-

ance so that the hose points toward the 

rear. 

Only slide the cleaning head halfway 

under the appliance.



Remove the lid of the cleaning head.



Connect the power cord of the cleaning 

head to the appliance (same colours 

must meet).



Replace the lid and lock it.



Slide the cleaning head halfway under 

the appliance.



Connect the hose couplers on the 

cleaning head to the hose on the appli-

ance.



Insert the tab into the middle of the 

cleaning head, between the fork of the 

lever.



Align the holder of the cleaning head so 

that the drilled holes in the lever and the 

cleaning head match.



Insert the stop pin through the bushings 

and swivel the locking plate downward.



Insert the cylinder pin into the boring of 

the drawbar.



Slide the drawbar with the pin the guide 

channel on the cleaning head all the 

way to the bottom.



Insert the locking plate into the guide 

channel and lock it in.



Repeat process on the drawbar on the 

opposite side.



Insert the grey intelligent key.



Set brush type "Disc".



Lift the holder of the cleaning head (see 

Chapter "Grey intelligent key/.../clean-

ing head replacement".



Slide the cleaning head under the appli-

ance so that the hose points toward the 

rear. 

Only slide the cleaning head halfway 

under the appliance.



Unscrew the star handle and remove 

the lid.



Connect the power cord of the cleaning 

head to the appliance (same colours 

must meet).



Slide the lid in and screw tight.



Slide the cleaning head halfway under 

the appliance.

Maintenance Works

Maintenance contract

Cleaning the protective turbine strainer

Replacing the vacuum lips

Install D cleaning head

Install R cleaning head

23 EN