AEG VL 5530 S: English

24

English

Any other use of this device is considered to be contrary

Position

to the intended use and may result in damage to materi-

The ideal position is a non-slip,  at surface.

als or even personal injury.

The  rm ETV - Elektro-Technische Vertriebsgesellschaft

Putting into Service

mbH does not accept any liability for damage caused as

a result of the use of this device contrary to its intended

Electrical Connection

use.

1. Before inserting the plug into the socket. Make sure

that the mains voltage to be used matches that of

Unpacking the Device

the device. You can  nd this information on the

nameplate.

• Remove the device from its packaging.

2. Connect the device to a duly installed 230V/50Hz

• Remove all of the packaging material such as foils,

protective contact socket. The control lamp POWER

 lling material, cable holders and cardboard packag-

now illuminates.

ing.

• Check the scope of delivery.

Remote Control

 NOTE:

• The cordless remote control has a range of up to 6

There may still be dust or production residues on the

meters.

surface of the device. We recommend that you quickly

• When using the remote control, please ensure that

wipe o the housing with a damp cloth.

there are no obstacles placed between it and the sen-

sor on the device.

• If this range becomes smaller the batteries need

Assembly instructions

replacing.

The device must be completely assembled before use!

Inserting Batteries into the Remote Control

While reading the text it is advisable to refer to the

(Batteries not supplied)

„Overview of the Components“.

• Open the lid of the battery compartment on the rear

1. Place the parts of the base together in the shape of a

of the remote control.

cross.

• Insert 2 MICRO batteries of type R03 „AAA“ 1.5 V.

2. Screw the mounting plate (15) tightly to the base.

• Please ensure the correct polarity. Information is

Four crosshead screws are included in the scope of

shown on the remote control itself.

delivery.

• Close the battery compartment.

3. Push the covering cap (14) on to the lowest position

of the upright tube (13).

 NOTE:

4. Loosen the connection screw (11) and insert the gear

• The buttons marked with an * are located on the

casing (10) and the motor casing (9) on the stand

device and on the remote control.

tube. Then tighten the screw well.

• If you are not going to use the remote control for

5. Position the rear protection grid (7) in place in accor-

a prolonged period, please remove the batteries in

dance with the recesses.

order to prevent them from leaking.

 NOTE:

CAUTION:

Please ensure that the carrying handle is facing

• Used batteries should not be disposed of in the do-

upwards.

mestic waste. Please return all batteries to a special

6. Turn the attachment ring (6) for the rear protection

collection point. Your local authority will provide

grid (7) slightly in a clockwise direction.

you with information on this.

7. Attach the propeller. Note the position of the guide

• Di erent types of battery or new and used batte-

pin on the motor shaft.

ries must not be used together.

8. Tighten the attachment screw (4) for the propeller in

an anticlockwise direction.

9. Insert the front protective grille (1).

Use

 NOTE:

Basic Settings

Ensure that the holes for the attachment screw in

Set the blower inclination angle before starting the

the front and rear protective grille are aligned one

device. You can adjust the inclination angle by tipping

above the other.

the blower casing with both hands.

10. Tighten the protective grille with the attachment

screw supplied.

CAUTION:

11. Close the attachment hooks.

The inclination angle amounts to approx. 15°.

05-VL 5530 S AEG.indd 2405-VL 5530 S AEG.indd 24 05.11.2008 9:19:49 Uhr05.11.2008 9:19:49 Uhr