Karcher Monobrosse ultra-haute-vitesse BDP 50-2000 RS Bp Pack: Transport Storage Maintenance and care

     

- 

5 

Danger

Danger of accident. The immobilizing brake 

must always be checked first on an even 

surface before starting the machine.



Press emergency-stop button.

If the appliance can be moved by hand, the 

parking brake is not engaged.



Pull up the reset lever of the parking 

break.

If the appliance can still be moved by hand, 

the parking break is defective. Shut down 

the appliance and call Customer Service.



Danger

Danger of accident. If the appliance cannot 

brake adequately while going downhill, 

press the emergency stop button.

Carry out the initial trials in an open surface 

so that you familiarise yourself with the ap-

pliance. 



Danger

Danger of tipping if gradient is too high.



The gradient in the direction of travel 

should not exceed 10%.

Danger of tipping when driving round 

bends at high speed.

Danger of slipping on wet floors.



Drive slowly when cornering.

Danger of tipping on unstable ground.



Only use the machine on sound surfaces.

Danger of tipping with excessive sideways 

tilt.



The gradient perpendicular to the direc-

tion of travel should not exceed 10%.



Step on the standing platform.



Do not press the accelerator pedal.



Release emergency-stop button by 

turning.



Set main switch to “1”.



Set the speed range on the programme 

selection switch.



Set the drive direction using the drive 

direction button at the operator console.



Press the accelerator carefully to drive. 

In case of overloading, the drive motor au-

tomatically switches off after a certain peri-

od. 



Allow the appliance to cool down at 

least for 5 minutes.



Step on the standing platform.



Do not press the accelerator pedal.



Release emergency-stop button by 

turning.



Set main switch to “1”.

몇

Warning!

Risk of damage to the floor covering. Do 

not operate the appliance on the spot.



Turn the programme selector switch to 

the desired function. 



Set the forward drive direction using the 

drive direction button at the operator 

console.



Press accelerator pedal and drive to the 

surface to be cleaned.



Park the machine on an even surface.



Turn key to "0" and remove it. 



Danger

Risk of injury! When loading or unloading 

the machine, it may only be operated on 

gradients of max. 10%. Drive slowly.

Caution

Risk of injury and damage! Observe the 

weight of the appliance when you transport 

it.



When transporting in vehicles, secure 

the appliance according to the guide-

lines from slipping and tipping over.

Fastening points

Caution

Risk of injury and damage! Note the weight 

of the appliance in case of storage.

This appliance must only be stored in inte-

rior rooms.



Danger

Risk of injury! Before carrying out any tasks 

on the machine, set the main key to "0" and 

remove it. Pull out the battery plug.

Disconnect the power cord of the charger.

Note

Suction turbine (option) overruns after 

shutdown. Carry out maintenance tasks 

only after the suction turbine has come to a 

halt.



Check tyre status.



Check the condition of the pad.



Check whether pads are sitting correctly. 



Check the pad driver plate for proper 

seating.



Check if the locking lever is released for 

replacing the pad driver plate. 



Check if a filter bag (option) is installed.



Check the inserts of the suction hose 

for leaks. 



Check accelerator pedal, brake and 

steering wheel for correct functioning.



Check acid level in wet batteries; refill 

distilled water, if required.



Close the battery cover and the upper 

part of the appliance.



Check filling level of the filter bag (op-

tion), replace if necessary.



Clean the outside of the appliance with 

a damp cloth which has been soaked in 

mild detergent.



Check device externally for damage. 



Charge the batteries.



Clean upper side of the batteries. 



Check acid density in wet batteries. 



Check battery cable for correct positioning. 



Check dust cover on the polishing head 

for wear and damage; replace, if re-

quired (see "Maintenance tasks"). 



Clean battery room and battery casing. 



Check immobilising brake. *



Clean the joints on the polishing head 

suspension.



Check carbon brushes and commuta-

tors of all motors for wear and tear. *



Check tension of steering chain. *



Check the tension of the drive chains on 

the drive. *

* To be done by Customer Service.

To ensure a reliable operation of the appli-

ance maintenance contracts can be con-

cluded with the competent Kärcher sales 

office.

1 Dust cover



Turn the programme selection switch to 

Drive.



Turn main key to "0" and remove it.



Look for the parting point of the dust 

cover and pull one end downwards out 

of the holders.



Pull the remaining dust cover off hori-

zontally.



Push the new dust cover up in the indi-

vidual holders and snap in place.



Shorten the dust cover by means of 

scissors or a side cutter.

Check immobilizing brake

Brakes

Driving

Overload

Polishing

Shutting down

Transport Storage Maintenance and care

Maintenance schedule

Prior to operation:

After operation:

Every 50 operating hours

Every 100 operating hours

Every 200 operating hours

Maintenance Works

Maintenance contract

Replacing dust cover

16 EN