AEG MC 4465 BT: English

54

English

Deactivating or activating the alarm function

Timer function

(in standby mode)

General

Briefly press the LIGHT/TIMER button. The display will show:

• Alarm with FM radio: Make sure to set the station to be

OFF= deactivated or ON= activated.

used for the alarm.

• Alarm with CD, USB or CARD modes: Make sure to insert

Delayed switch-off

a CD or to connect the desired storage medium. If no CD

is inserted or no storage medium is connected, the alarm

Do you like to fall asleep with music?

will automatically sound with the radio station listened to

1. Turn on the device with the desired operating mode.

last.

2. Press the SLEEP button (11 on the remote control). The

• Once the pre-set alarm time has been reached, the

display will show “SLP” and “90” indicating the minutes.

device will activate the selected mode. “

“ will flash

“

” will be flashing.

on the display. The volume will gradually increase to the

3. Reduce the time in increments of 10 minutes by pressing

selected volume setting.

the SLEEP button.

4. After you have set the desired time, the “ ” indicator

Setting the timer

lights up.

Use this function for the device to switch off and on at a

• Selecting “SLP OFF” will deactivate the funciton.

specific time. Proceed as follows:

1. Use the I/

button (22) to switch the device to standby.

Cleaning and Maintenance

2. Press and hold the LIGHT/TIMER button (16) for approx.

3 seconds. “ ” appears in the display and “ON TIMER”

WARNING:

appears as scrolling text. After that, the hours of the set

Do not immerse the device in water.

alarm time start flashing.

3. Use the /TUNE+ and /TUNE– buttons (9/17) to adjust

• Always remove the mains plug before cleaning the

the settings accordingly.

machine.

4. Press the LIGHT/TIMER button to confirm. The minutes

• Any marks on the surface can be wiped off with a slightly

start flashing.

damp cloth without any additives.

5. Use the /TUNE+ and /TUNE– buttons to adjust the

settings accordingly.

Troubleshooting

6. Press the LIGHT/TIMER button to confirm.

7. Then use the VOLUME rotary control to adjust the vol-

Symptoms Course Solution

ume to be used when switching the device on.

CD can not be

CD is not inserted

Ensure that the disc is

8. Press the LIGHT/TIMER button to confirm. Then use the

played back.

or inserted incor

-

inserted with the label

FUNCTION button to select the alarm mode: FM, CD,

rectly.

facing upwards.

USB or CARD.

CD jumps dur

-

Check the disc for

Check the disc for

9. Press the LIGHT/TIMER button to confirm. “OFF TIMER”

ing playback.

fingerprints, dirt or

fingerprints, dirt or

appears as scrolling text. Then the hours of the current

scratches.

scratches.

time, after which the device will switch off, start flashing.

Device cannot

Device crashes and

Disconnect the power

10. Use the /TUNE+ and /TUNE– buttons to adjust the

be operated.

“hangs”.

supply for 5 sec. Then

settings accordingly.

switch the device on

11. Press the LIGHT/TIMER button to confirm. The minutes

again.

start flashing.

No audio

The device is not

Ensure that there is a

12. Use the /TUNE+ and /TUNE– buttons to adjust the

signal during

registered with the

connection. Register

settings accordingly.

bluetooth con

-

audio source.

the device with the

13. Press the LIGHT/TIMER button to complete the settings.

nection.

audio source again, if

The timer is set. “ ” and the current time appear in the

necessary.

display.

Volume too low. Increase the volume

Turning off the alarm

on the device.

In order to deactivate the alarm until the next day prior to

Increase the volume

reaching the preset “OFF TIMER” time, press the I/

button.

on the audio source.