AEG BSS 4814: English

English: AEG BSS 4814

English

37

Remote Control

• Stickthedowels(D)intotheboreholesandfasten

1 INPUT button (select source)

the mounting plates to the wall with the countersunk

2 RESET button

screws(C).

3

button (Mute)

• Twistthethreadedbolts(A)intothebacksideofthe

4 NORMAL / MUSIC / MOVIE buttons (equalizer)

sound bar so far that there is enough space between the

5

button(nextmusicpiece)

wall and the connection cable.

6 >>/<< buttons

CAUTION: IMPORTANT!

7 button (increase the volume)

For an optimal wall mounting we recommend the use

8 ST/MONO button (Stereo/Mono switch)

of connection cables with an angled connection. You

9

(play/pause) button

can obtain corresponding cables from the specialist

10 button (decrease the volume)

shop.

11 CH+/CH-/MEMORY buttons

12

button (previous music piece)

• Hangthedeviceintothemountingplates(B)withthe

13 TREBLE+/TREBLE- buttons (adjust trebles)

screws (A). Check for stable support.

BASS+/BASS- buttons (adjust basses)

14

button (On/Operational readiness)

Establishing the power supply and cable connection

• Makesurethegridvoltagecorrespondstothegureson

Wall mounting

the rating plate.

A Threadedbolt(2x)

• Connectthesoundbarandthesubwooferwiththecon-

B Mountingplate(2x)

nection cable. Plug the angled end into the socket on the

C Countersunkscrew(4x)

back of the sound bar and the other end of the cable into

D Dowel(4x)

the SPEAKER OUTPUT connection (6) of the subwoofer.

• Plugthemainsplug(7)intoaproperlyinstalledearthed

socket.

First Use of the Device/Introduction

• Turnonthesubwooferbyswitchingthepowerswitchon

the back side of the device to the “ON” position.

NOTE:

• Thedeviceisoperatedprimarilywiththeremotecon-

Insert/Replace Battery in Remote Control

trol. Thus the descriptions refer to the buttons on the

remote control. Some buttons are also on the device.

NOTE:

Buttons with the same name have the same function.

The lithium cell in the battery compartment of the remote

• Thebuttonsonthedevicearetouchbuttons.Touchthe

control was possibly secured with a foil for the transport.

buttons lightly with a finger to perform the function.

This prolongs the lifetime of the battery. Please remove this

foil before the first use to make the remote control ready

• Selectaproperplaceforthedevice.Adry,levelandslip

for operation.

proof surface is suitable.

• Makesurethedeviceisventedsufciently!

• Openthebatterycompartmentontheundersideofthe

• Removetheprotectivelmfromthedevice,ifpresent.

remote.

• Replacethecellwithabatteryofthesametype(CR2025).

Wall mounting (Sound bar)

Check that the polarity is correct (see battery compart-

You can also mount the device to the wall.

ment).

• Closethebatterycompartment.

CAUTION:

If the remote is not in use for a lengthy period of time, please

Make sure beforehand whether there are cables in the wall

remove the battery to prevent the battery acid from “leaking”.

which could be damaged!

WARNING:

NOTE: Check the reach of the cable!

• Donotexposethebatteriestointenseheat,suchas

To mount the device, make sure that an easily accessible

sunlight, fire or similar. Danger of explosion!

plug outlet is available within reach of the power cable.

• Keepbatteriesoutofthereachofchildren.Theyare

The distance between the mountings for wall mounting is

not toys.

660 mm.

• Donotforcebatteriesopen.

• Avoidcontactwithmetallicobjects.(Rings,nails,screws

• Holdthemountingplate(B)tothewallsothattheabove-

etc.) Danger of short circuits!

listed distance is kept horizontally and from the center of

• Shortcircuitsmayoverheatorevenignitebatteries.

the mounting plates.

This may lead to combustion.

• Markthefourpositionsofthemountingholeswithapen-

• Whentransportingthebatteries,covertheterminalsfor

cil.

your safety with an adhesive strip.

• Drillthemountingholes(diameter6mm).