AEG SR4356 BT: English
English: AEG SR4356 BT
36
English
• If the device is not used for a long period of time, remove
Special safety information
the batteries to avoid the spilling of battery acid.
• Then close the battery lid.
This device works with a class 1 laser.
NOTE:
When a mains cable is connected the batteries are auto-
matically switched off.
Overview of the Components
CAUTION:
• Different battery types or new and used batteries must
1 Telescopic antenna
not be used together.
2 CD compartment
• Batteries are not to be disposed of together with
3 OPEN/CLOSE button
domestic wastes. Dispose of the used batteries at the
4 TUNING control
relevant collection bin or at your dealer’s.
5 /PAIR button
6 button
WARNING:
7 PROG/P-MODE button
The batteries shall not be exposed to excessive heat such
8 / buttons
as sunshine, fire or the like. Danger of explosion!
9 Display
10 PAIR/STANDBY control lamp (bluetooth/operating status)
Transport Safety Device, CD Compartment
11 - FOLD./10+ buttons
12 BAND button
• Open the CD tray (2) by pressing the OPEN/CLOSE but-
13 FUNC. button
ton (3).
14
/STANDBY button
• Before operating the machine for the rst time, remove
15 VOLUME control
the transport safety device from the CD player if it is still
16 USB port
in place.
17 AUX-IN input
Volume
Reverse (not shown)
You can adjust the desired volume with the VOLUME control
AC Mains connection
(15).
Underside (not shown)
Turning device on/ off
Battery compartment
• Press the
/STANDBY button (14) to turn the device on.
• To turn off the device, press the
/STANDBY button
again. The control lamp PAIR/STANDBY (10) lights up
Start-up of the device/introduction
red.
• Select a suitable location for the device, such as a dry,
NOTE:
flat, non-slip surface on which it is easy to operate the
After about 15 minute without a signal, the device will
machine.
automatically switch to standby.
• Ensure that the device is sufciently ventilated!
• Remove the protective lm from the display if it is still
present.
Listening to the Radio
Power Supply
1. Select the radio mode with the FUNC button (13).
2. Completely extend the telescopic antenna. Change its
• Connect the power cable supplied (see battery compart-
position to improve the reception. An antenna is inte-
ment if necessary) to a properly installed safety power
grated to receive AM stations. By turning and adjusting it,
socket and the mains connector AC on the back of the
the device can be aligned to the station. Programs in this
machine.
frequency band are only broadcast in mono.
• Ensure that the voltage is the same as that indicated on
3. Select the desired frequency band with the BAND button
the model identification plate.
(12).
Inserting the Batteries (not supplied)
FM = Frequency modulation, AM = Medium wave
• Open the lid of the battery compartment on the bottom.
4. Tune the desired station with the TUNING control (4). For
• Insert 6 batteries of type UM2/R14 1.5 V. Please ensure
FM stations, the notification “STEREO” will appear on
that the polarity is correct (see the floor of the battery
the display if the station is received in stereo.
compartment)!
Оглавление
- Inhalt
- Übersicht der Bedienelemente
- Deutsch
- Deutsch
- Deutsch
- Deutsch
- Deutsch
- Deutsch
- Deutsch
- Nederlands
- Nederlands
- Nederlands
- Nederlands
- Nederlands
- Nederlands
- Français
- Français
- Français
- Français
- Français
- Français
- Español
- Español
- Español
- Español
- Español
- Español
- Italiano
- Italiano
- Italiano
- Italiano
- Italiano
- Italiano
- English
- English
- English
- English
- English
- English
- Język polski
- Język polski
- Język polski
- Język polski
- Język polski
- Język polski
- Język polski
- Magyarul
- Magyarul
- Magyarul
- Magyarul
- Magyarul
- Magyarul
- Українська
- Українська
- Українська
- Українська
- Українська
- Українська
- Русский
- Русский
- Русский
- Русский
- Русский
- Русский