AEG bqs 5515: English
English: AEG bqs 5515
31
English
Operating your device
•
Pour 1.5 l of cold water into the grill base until
reaching the “MAX” level.
•
Preheat the operable device for about 10
minutes prior use.
•
Set the temperature control according to the
intended use:
Low or middle settings for keeping warm or
cooking, highest setting for fast cooking or
barbecuing. The indicator light (9) indicates the
operation of the heating.
Electric installation
•
Put the barbecue onto the grill plate. Turn the
barbecue from time to time.
•
Be sure the voltage of the device (rating plate)
is in accordance with the mains voltage.
Caution:
•
Connect the mains plug to a properly installed
If the water level falls below the “MIN” marking
shockproof socket (230V~ 50Hz) only.
after long time of barbecuing, please rst un-
plug the device and then add more water, until
Connected load
reaching the “MAX” level.
The device is intended for a maximum power
Do not pour cold water over the hot heating
intake of 2000 W. This connected load recom-
element. It might get damaged.
mends a separate input lead secured with a
16 amp protected switch.
Switch off:
Turn the temperature control anti-clockwise as
Caution Overload:
far as it will go and unplug the device.
►
When using extension cords, these should
have a cable cross-section of at least 1.5 mm².
►
Do not use gang plugs, because the device
Troubleshooting
is too powerful.
The thermostat is equipped with a safety switch
The device must be supplied by a residual-cur-
(A). It prevents the operation of the heating ele-
rent-operated protective device (RCD) with a
ment outside of the grill base.
release current of maximum 30mA.
If the heating cannot be switched on, please
Please consult a qualied electrician.
check the mains connection and the correct tting
of the thermostat in the grill base.
Prior rst-time operation
Cleaning
•
Slightly grease the anti-stick grill plate and put
it onto the heating coil.
Warning:
•
Operate the device without barbecue for 15
►
Always unplug the device and allow the
minutes whilst grill base is lled with water.
device to cool down before cleaning.
•
Turn the temperature control (8) to the highest
►
Do not under any circumstances immerse
position.
the heating element into water for cleaning.
•
The protective foils on the heating element and
Danger of electric shock or re!
grill plate will be removed.
Caution:
Note:
►
Do not use a wire brush or other scratching
Slight formation of smoke is thereby normal.
objects.
Ensure sufcient ventilation.
►
Do not use acrid or abrasive cleaning
agents.
•
Clean the grill plate during a rinsing bath after
it has cooled down.
Remove the grill plate and the heating element,
Your device is now ready for use.
and take the reector plate from the grill base.
Pour the water of the grill base away.
Оглавление
- Bedienungsanleitung/Garantie
- Inhalt
- Übersicht der Bedienelemente
- Deutsch
- Deutsch
- Deutsch
- Deutsch
- Deutsch
- Nederlands
- Nederlands
- Nederlands
- Nederlands
- Français
- Français
- Français
- Français
- Español
- Español
- Español
- Español
- Português
- Português
- Português
- Português
- Italiano
- Italiano
- Italiano
- Italiano
- English
- English
- English
- English
- Język polski
- Język polski
- Język polski
- Język polski
- Język polski
- Česky
- Česky
- Česky
- Česky
- Magyarul
- Magyarul
- Magyarul
- Magyarul
- УКРАЇНСЬКА
- УКРАЇНСЬКА
- УКРАЇНСЬКА
- УКРАЇНСЬКА
- Русский
- Русский
- Русский
- Русский