AEG SB2E1100RV 4935447375: English English
English English: AEG SB2E1100RV 4935447375
SPECIFIED CONDITIONS OF USE
WARNING! Read all safety warnings and all instruc-
The electronic percussion drill/screwdriver can be universally used
tions. Failure to follow the warnings and instructions may result in
for drilling, percussion drilling, screwdriving and cutting screw
electric shock, re and/or serious injury.
threads.
Save all warnings and instructions for future reference.
Do not use this product in any other way as stated for normal use.
DRILL SAFETY WARNINGS
ECDECLARATION OF CONFORMITY
Wear ear protectors when impact drilling. Exposure to noise
We declare under our sole responsibility that the product described
can cause hearing loss.
under “Technical Data” fullls all the relevant provisions of the
Use auxiliary handle(s), if supplied with the tool. Loss of
directives 2011/65/EU (RoHS), 2004/108/EC, 2006/42/EC and the
control can cause personal injury.
following harmonized standards have been used:
Hold power tool by insulated gripping surfaces, when
EN 60745-1:2009 + A11:2010
performing an operation where the cutting accessory may
EN 60745-2-1:2010
contact hidden wiring or its own cord. Cutting accessory con-
EN 60745-2-2:2010
tacting a “live” wire may make exposed metal parts of the power
EN 55014-1:2006 + A1:2009 + A2:2011
tool “live” and could give the operator an electric shock.
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
SCREWDRIVER SAFETY WARNINGS
EN 61000-3-3:2013
Hold power tool by insulated gripping surfaces, when
EN 50581:2012
GB
performing an operation where the fastener may contact
hidden wiring or its own cord. Fasteners contacting a “live”
wire may make exposed metal parts of the power tool “live” and
Winnenden, 2014-09-01
could give the operator an electric shock.
Additional Safety and Working Instructions:
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is re-
Alexander Krug / Managing Director
commended, such as dust mask, protective gloves, sturdy non-slip
Authorized to compile the technical le
footwear, helmet and ear defenders.
Keep mains lead clear from working range of the machine. Always
Techtronic Industries GmbH
lead the cable away behind you.
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Do not machine any materials that present a danger to health (e.g.
asbestos).
MAINS CONNECTION
When working in walls ceiling, or oor, take care to avoid electric
Appliances used at many dierent locations including wet room
cables and gas or waterpipes.
and open air must be connected via a residual current device (FI,
Clamp your workpiece with a clamping device. Unclamped workpi-
RCD, PRCD) of 30mA or less.
eces can cause severe injury and damage.
Connect only to single-phase AC system voltage as indicated on
Switch the device o immediately if the insertion tool stalls! Do
the rating plate. It is also possible to connect to sockets without an
not switch the device on again while the insertion tool is stalled,
earthing contact as the design conforms to safety class II.
as doing so could trigger a sudden recoil with a high reactive force.
Make sure the machine is switched o before plugging in.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
MAINTENANCE
The possible causes may be:
The ventilation slots of the machine must be kept clear at all times.
• it is tilted in the workpiece to be machined
If the machine is mainly used for percussion drilling, regularly
• it has pierced through the material to be machined
remove collected dust from the chuck. To remove the dust hold the
• the power tool is overloaded
machine with the chuck facing down vertically, and completely
Do not reach into the machine while it is running.
open and close the chuck. The collected dust will fall from the
The insertion tool may become hot during use.
chuck. It is recommended to regularly use cleaner for the clamping
WARNING! Danger of burns
jaws and the clamping jaw borings.
• when changing tools
If the supply cord of this appliance is damaged, it must only be
• when setting the device down
replaced by a repair shop appointed by the manufacturer, to avoid
Chips and splinters must not be removed while the machine is
hazardous situations.
running.
Use only AEG accessories and spare parts. Should components
Before doing any work on the machine, pull the plug out of the
need to be replaced which have not been described, please contact
socket.
one of our AEG service agents (see our list of guarantee/service
addresses).
English
English
14
Оглавление
- English English
- English English
- English English
- English Deutsch
- Deutsch English
- English Deutsch
- Français English
- English Français
- Français English
- English Italiano
- Italiano English
- English Italiano
- Español English
- English Español
- Español English
- English Português
- Português English
- English Português
- Nederlands English
- English Nederlands
- Nederlands English
- English Dansk
- English Norsk
- English Svenska
- Svenska English
- English Svenska
- English Suomi
- English Ελληνικά
- Ελληνικά English
- English Ελληνικά
- English Türkçe
- English Česky
- Slovensky English
- English Slovensky
- Slovensky English
- English Polski
- Magyar English
- English Magyar
- Magyar English
- English Slovensko
- Slovensko English
- English Slovensko
- Hrvatski English
- English Hrvatski
- Hrvatski English
- English Latviski
- Latviski English
- English Latviski
- Lietuviškai English
- English Lietuviškai
- Lietuviškai English
- English Eesti
- Pусский English
- English Pусский
- Pусский English
- English български
- български English
- English български
- Romănia English
- English Romănia
- Romănia English
- English Македонски
- Македонски English
- English Македонски
- English 中文